Heat & Glo LifeStyle 6000TRI-SP manual Installing the Optional Heat-Zone Kit, Gas Control Systems

Page 27

Step 5. Installing the Optional Heat-Zone Kit

NOTE: There must be NO INSULATION or other com- bustibles inside the framed firestop opening.

HEAT-ZONE

ATTACHES

HERE

Figure 32.

1.Remove the knockout from the fireplace and discard it (see Figure 32).

2.Center the duct collar around the exposed hole and at- tach it to the fireplace with 3 screws. NOTE: Do this BE- FORE final positioning of the fireplace.

3.Determine the location for the air register/fan housing assembly.

Reference the Heat-Zone kit instructions for the remaining installation steps.

Step 6. The Gas Control Systems

!WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

The types of gas control systems used with this model are Intermittent Pilot Ignition (IPI) and Standing Pilot Ignition (SP).

Intermittent Pilot Ignition (IPI) System

This system includes a 3V control valve, electronic module and intermittent pilot.

!WARNING: CONTINUOUS 110-120 VAC SER-

VICE MUST BE WIRED DIRECTLY TO THE FIRE- PLACE JUNCTION BOX.

FLAME SENSOR

ROD

Figure 33. Gas Control System (IPI)

Standing Pilot Ignition System

This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor.

WARNING: 110-120 VAC MUST NEVER BE ! CONNECTED TO A CONTROL VALVE IN A

MILLIVOLT SYSTEM.

Figure 34. Gas Control System (Standing Pilot)

Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05

27

Image 27

Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents 6000TRI-IPI, 6000TRI-SP Log set assembly6000TRI-SP, 6000TRI-IPI Service Parts List / Liste des pièces de rechange6000TRI-IPI Intermittent Pilot Ignition Valve Assembly6000TRI-SP Standing Pilot Ignition Valve AssemblyCertification Installation CodesHigh Altitude Installations Appliance CertificationPre-install Preparation Introducing the Heat & Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000TRI-IPI, 6000TRI-SP Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace Framing DimensionsDVP90ST Identifying Vent Components Installing the Vent SystemVent System Approvals Tems or Components MAY be UsedFlue Restrictor Instructions Vertical VentingMAX .4 M Straight Up Vertical Venting Chart Venting with One 90 Elbow Venting with ONE 1 90 ElbowVenting with Two 90 Elbows Venting with TWO 2 90 o ElbowsVenting with three 90 elbows Venting with Three 3 90 Elbows+ V 1 FT + H 1 FT Installing Vent Components To Install the Heat Shield Install Support BracketsContinue Adding Vent Components 12 Hole and Vent Pipe Attic Firestop Vent TerminationVent Termination Minimum Clearances Positioning, Leveling, Securing the Fireplace Proper PositioningLeveling and Securing of a Fireplace Intermittent Pilot Ignition IPI System Installing the Optional Heat-Zone KitVice Must be Wired Directly to the FIRE- Place Junction BOX Gas Control SystemsGas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Intermittent Pilot Ignition IPI Wiring Diagram Wiring the Fireplace Sealant Material Hearth Extensions FinishingInstalling Trim, Logs, and Ember Material Double-check for faulty components Air Shutter SettingBefore Lighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace After the InstallationFireplace Maintenance Lighting the Fireplace