Desa (V)CB36P(E), (V)CB36N(E) Checking for Proper Venting, Electrical Supply Connection

Venting Installation

			Continued
Lowest		Listed
Discharge
		Vent Cap
Opening			8 Ft. Min.
	Listed			x
	Gas
	Vent	12			Roof Pitch x/12
					Listed Clearance
H (Min)
Height			Roof Pitch			H (Min.)
From Roof			Flat to 6/12			1.0 ft (0.3 m)
			6/12 to 7/12			1.25 ft (0.38 m)
			Over 7/12 to 8/12			1.5 ft (0.46 m)
			Over 8/12 to 9/12			2.0 ft (0.61 m)
			Over 9/12 to 10/12			2.5 ft (0.76 m)
			Over 10/12 to 11/12			3.25 ft (0.99 m)
			Over 11/12 to 12/12			4.0 ft (1.22 m)
			Over 12/12 to 14/12			5.0 ft (1.52 m)
			Over 14/12 to 16/12			6.0 ft (1.83 m)
			Over 16/12 to 18/12			7.0 ft (2.13 m)
			Over 18/12 to 20/12			7.5 ft (2.27 m)
			Over 20/12 to 21/12			8.0 ft (2.44 m)

Figure 11 - B-Vent Termination

Checking for Proper Venting

After completing and checking the electrical, gas and vent connections, follow the lighting instruc- tions and allow the main burner to run for approxi- mately 5 minutes. Hold a match or butane lighter flame, near the opening between the glass and the fireplace face and play it along the entire length of the opening (Smoke may also be used). Proper venting will tend to draw flame or smoke into the appliance. Improper venting, escaping or spillage of burned gas, is indicated when the match flickers or goes out (see Figure 12). Smoke will also tend to disperse away from the appliance.

If the appliance is not venting properly, shut it off and notify your installer or a qualified service agency to inspect the venting system.

Electrical Supply Connection

CAUTION: Disconnect the electrical power to the supply circuit before attempting to con- nect or service this appliance.

A prewired junction box receptacle with strain relief is provided on the right side of the cabinet for hard wiring the unit to a 15 Amp, 120 VAC, 60 Hz grounded branch circuit. If the installation demands that the electrical supply be connected from the left side, the entire receptacle box can be relocated to the left side by following these instructions:

Note: If you do not need to relocate the junction box, to connect the electric supply follow steps 8 through 11 only:

1. Remove 2 screws and outer cover with strain relief bushing on right side of cabinet (see Figure 13).

2. Remove inner retaining screw on junction box mounting tab.

3. Slide junction box up until screw mounting tab is lined up to notch in outer cabinet.

4. Swing junction box out and slip retaining flange out through slot in outer cabinet.

5. Remove 2 screws and outer cover on left side of outer cabinet.

6. Reinsert junction box retaining flange through slot now on left side and swing screw mount- ing tab back through notch as before.

7. Slide junction box down till mounting tab holes line up and replace inner retaining screw.

8. With junction box cover removed, pull end of 3-wire Romex supply line through uni- versal strain relief bushing on cover. (see Figure 13).

J-Box	J-Box
Cover
	Cover
with Strain		J-Box Cover
Relilef		with Strain
		Relief

Romex Cable

J-Box with

Receptacle

Screw/Tab Retainer

Figure 12 - Checking for Spillage

Figure 13 - Relocating Junction Box Recep-

tacle and Electrical Supply Connection

10 www.desatech.com 117437-01B