Desa (V)CB36P(E), (V)CB36N(E) Packaging and Removal, Clearances, Framing and Finishing

Page 6

Pre-Installation

Preparation

Continued

•A hearth extension is not required with this appliance. If one is installed, it is for aesthetic purposes only and does not have to meet stan- dard requirements for hearth extensions.

•If you plan on installing a television or entertain- ment center recessed above your fireplace, it is recommended that you maintain a minimum 18" (45.7 cm) above the top of louver opening.

•When locating the termination cap, it is impor- tant to observe the minimum vent height and clearances required under code, see Venting Installation Instructions, page 8.

•Do not recess termination cap into a wall or siding.

•You may paint the termination cap with 450° F

(232° C) heat resistant paint to coordinate with the exterior finish.

PACKAGING AND REMOVAL

The (V)CB36 vented decorative gas fireplaces are packaged with the following items:

•one box containing a 4 piece log set located on the burner in the firebox.

•one bag containing the owner’s manual with installation instructions, operator’s guide, and warranty information.

•one bag of glowing ember material.

•one bag of vermiculite hearth treatments.

1.Remove shrink wrap securing 2 carton trays to unit.

2.Lift top carton tray off and remove four corner posts.

3.Discard bottom tray once unit is moved into position.

Carton

Tray

Corner

Post

Glass

Panel

Log

Carton

Figure 4 - Unpacking Fireplace

Note: To prevent damage to ceramic logs and glass panels you may want to remove them before positioning and framing the unit. To access firebox, see Louver Panels and Glass Door, page 16.

CLEARANCES

Minimum clearances to combustibles for fireplace:

Back, Sides, Floor and Top

0" (0 mm)

Perpendicular walls

10" (25.4 cm)

Ceiling to Louver & Front

36" (91.4 cm)

B-Vent Surfaces

1" (26 mm) (See

 

venting instructions

 

for specifics on vent

Mantel Clearances

clearances.)

(See Mantel Clear-

 

ances, page 7, for

 

specific clearances to

 

combustible mantels.)

Combustible material with a maximum thickness of 5/8" (16 mm) may be flush with top and sides of front face of fireplace.

FRAMING AND FINISHING

Figure 5 shows typical framing of this fireplace. Figure 6, page 7, shows framing for corner instal- lation. All minimum clearances must be met.

For overall unit dimensions, framing allowances and vent collar locations, see Unit Dimensions, Figure 7 on page 7.

For available accessories for this fireplace, see Accessories, page 34. If you are using a separate combustible mantel piece, refer to Figures 8 and 9, page 8, for proper height and clearances. You can install a noncombustible mantel at any height above the fireplace opening.

Note: Noncombustible mantels may discolor!

36"

(91.4 cm)

36 1/4"

 

(92.1 cm)

14 3/4"

 

(37.5 cm)

Figure 5 - Framing Clearances for Flush

Wall Installation



www.desatech.com

117437-01B

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Models VCB36NE and VCB36PETable of Contents Safety information Product Identification Local CodesProduct Features Pre-Installation PreparationLocation and space requirements Packaging and Removal ClearancesFraming and Finishing Mantel Clearances However, 0 clearance is alsoInstallation Precautions Venting InstallationVenting Installation Checking for Proper Venting Electrical Supply ConnectionInstalling Optional Wall Mount Switch GWMS2 Installing Optional ControlsHigh Altitude Installation Installing Remote ReceiverInstalling Optional Controls Installing and Activating the Remote ReceiverMillivolt Wiring Diagram Wiring DiagramsInstallation Items Needed Fireplace InstallationInstalling Gas Piping to Fireplace Location Check GAS TypeConnecting Fireplace to GAS Supply Checking GAS ConnectionsNatural From Pressure Testing Fireplace Gas Connections Louver Panels and Glass DoorTest Pressures Equal To or Less Than Psig 3.5 kPa Removing Louver Panels Removing/Replacing Glass Door Spring ClipsGlass Panel Frame Rail Installing Logs and Glowing Embers Applying Ember MaterialLighting Instructions Manual Ignition System For your safety Read before lightingOperating Fireplace To Turn OFF GAS To ApplianceManual Lighting Procedure Optional Wireless Remote OperationElectronic Ignition System Lighting Instructions Optional GWMS2 ON/OFF Wall Mounted Switch Optional Hand-HeldOn/Off Series Model HRC100 Inspecting Burners Pilot AssemblyAir Adjustment Setting Burner Flame PatternsCleaning Maintenance Glass DoorPilot and Burners Venting System SpecificationsLogs VCB36NETroubleshooting Observed Problem Possible Cause RemedyLong enough Observed Problem Possible Cause Remedy See Lighting InstructionsNo gas supply, or shutoff Troubleshooting Statement aboveIllustrated Parts Breakdown Parts List Illustrated Parts Breakdown Instructions Technical Services Replacement PartsService Hints AccessoriesRemote Control KIT WRC Series Wall Mounted ON/OFF SwitchGWMS2 Not Shown Warranty Information Keep this WarrantyLimited Warranty Vent Fireplace

(V)CB36P(E), (V)CB36N(E) specifications

The Desa (V)CB36N(E) and (V)CB36P(E) represent a significant advancement in heating technology, offering efficient and reliable heating solutions for diverse residential needs. Both models showcase an amalgamation of modern design, energy efficiency, and user-friendly features, making them ideal for contemporary living spaces.

One of the standout features of the Desa (V)CB36N(E) and (V)CB36P(E) is their exceptional heating capacity. Designed to deliver a consistent and comfortable temperature, these units can effectively heat areas of various sizes, ensuring that even larger living rooms or open spaces maintain a cozy ambiance. The (V)CB36N(E) is particularly noted for its natural gas compatibility, while the (V)CB36P(E) offers flexibility with propane options, catering to varying user preferences and available fuel sources.

Both models are equipped with advanced technologies that enhance their performance and efficiency. The use of high-efficiency burners significantly boosts their output while minimizing fuel consumption. This strategic design not only prolongs the lifespan of the units but also contributes to reduced greenhouse gas emissions, aligning with the growing demand for environmentally friendly heating solutions.

In terms of safety, Desa places a strong emphasis on user protection. Each unit is equipped with a robust safety shut-off system that activates when certain operational parameters are not met, ensuring peace of mind for users. Additionally, the inclusion of a protective mesh screen on both models helps prevent accidental burns, particularly important in households with children or pets.

Aesthetically, the Desa (V)CB36N(E) and (V)CB36P(E) blend seamlessly into any interior décor. With customizable design options and finishes, users can select models that best fit their home’s theme, whether it be contemporary, rustic, or traditional. This flexibility helps homeowners enhance their living spaces while also reaping the functional benefits of these heating units.

Furthermore, the intuitive controls allow for effortless operation, making temperature adjustments quick and convenient. With remote control capabilities available in some models, users can manage their heating systems from the comfort of their seating areas.

In conclusion, the Desa (V)CB36N(E) and (V)CB36P(E) offer a perfect combination of performance, safety, and style. With their innovative technologies and user-friendly features, these heating solutions stand out in the market as reliable choices for those seeking efficient home heating options.
Top Page Image Contents