Desa VYGF33NRC, FPVF33PRA Checking Gas Connections, Models VYGF33PRB and VYGF33NRB

Page 11

Installation

Continued

10.If blower is installed, route blower electrical cord through access holes in either side of fireplace. Note: Bushing may be moved if necessary. Plug electrical cord into electrical outlet.

11.Carefully insert fireplace into cabinet mantel. Be careful not to scratch or damage hearth base, cabinet mantel or any laminate trim on hearth base (VYGF models only). Remove protective material from top of hearth base and from front of fireplace (if any). Note: You can secure fireplace to hearth or floor. Open lower louver. Locate screw holes in bottom of base. Tighten wood screws through these holes and into hearth or floor.

12.Check all gas connections for leaks. See

Checking Gas Connections, page 15.

Built-In Fireplace Installation Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. If installing a mantel above the fireplace, you must follow the clearances shown in Figure 20, page 13. Follow the instructions below to install the fireplace in this manner.

 

Actual

Framing

 

 

 

Height

32 3/8"

33"

Front Width

34 5/16"

35 1/2"

Depth

16 11/16"

17 3/4"

Models VYGF33PRB and VYGF33NRB

1. Frame in rough opening. Use dimensions shown in Figure 13 for the rough opening. If installing in a corner, use dimensions shown in Figure 14 for the rough opening. The height is 33" which is the same as the wall opening above.

2. If using blower, install and properly ground GA3555, three-prong 120 volt electrical out- let, in fireplace. Follow instructions included in kit (see Accessories, page 38).

3. Install gas piping to fireplace location. This in- stallation includes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Install- ing Gas Piping to Fireplace Location, page 13.

4. Carefully set fireplace in front of rough opening with back of fireplace inside wall opening.

5. Plug electrical cord into electrical outlet installed in step 2.

6.Carefully insert fireplace into rough opening.

7.Attach flexible gas line to gas supply. See Con- necting Fireplace to Gas Supply, page 14.

8.Attach fireplace to wall studs using nails or wood screws through holes in nailing flange (see Figure 15).

9.Check all gas connections for leaks. See

Checking Gas Connections, page 15.

10.Install perimeter trim after final finishing and/or painting of wall (see Figure 7, page 9).

17 3/4"

33"

35 1/2"

Figure 13 - Rough Opening for Installing

in Wall

393/8"

27 7/8"

35 1/2" 55 5/8"

Figure 14 - Rough Opening for Installing

in Corner

Nails or

Wood

Screws

Nailing

Flanges

Figure 15 - Attaching Fireplace to Wall

Studs

113109-01C

www.desatech.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Patent Pending VYGF33PRC, VYGF33NRC, FPVF33PRA millivoltFPVF33NRA Millivolt Remote-Ready Gas Fireplace SystemsSafety Information Table of ContentsSafety Information Product Identification Troubleshooting,Air For Combustion Ventilation Product FeaturesLocal Codes UnpackingConfined and Unconfined Space Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Unusually Tight ConstructionVentilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Electrical Hookup InstallationInstalling Hood Check GAS TypeRepeat steps 1 through 6 for other side Installation ClearancesPlacing Hearth Base Accessory Against Wall Conventional Fireplace InstallationModels VYGF33PRB and VYGF33NRB Checking Gas Connections,Models FPVF33PRA and FPVF33NRA Connecting Duplex OutletInstallation Items Needed Installing Gas Piping to Fireplace LocationMantel Clearances for Built-In Installation Propane/LP Connecting Fireplace to GAS SupplyAccessories, Natural Gas From Gas Meter 5 W.C.** toNatural Gas Checking GAS ConnectionsChecking Gas Connections Test Pressures Equal To or Less Than Psig 3.5 kPa Pressure Testing Fireplace Gas ConnectionsVygf Models Only Installing LogsFpvf Models Only Installing Remote Receiver UnitInstalling 9-Volt Battery in Hand-Held Remote Control Unit Installing 9-Volt BatteriesFor Your Safety Read Before Lighting Installing 9-Volt Battery in ReceiverLighting Instructions Operating FireplaceRemote Operation  MANUAL Lighting ProcedureTo Turn OFF GAS To Appliance Optional Hand-HeldOptional Blower Operation Thermostat Series Model HRC200Burner Primary AIR Holes Inspecting BurnerPilot Flame Pattern Burner Flame PatternLogs Cleaning MaintenanceBurner Injector Holder and Pilot Air Inlet Hole Ing and Maintenance, TroubleshootingObserved Problem Possible Cause Remedy See Cleaning and Mainte Diagram,Maintenance, On windows Tilation air Stalling Logs, Gas leak. See WarningSee Checking Gas Connec Technical Service Wiring DiagramSpecifications Replacement PartsModels VYGF33PRC and VYGF33NRC Shown Illustrated Parts BreakdownParts List Models FPVF33PRA and FPVF33NRA KEY Description Firebox Models VYGF33PRC and VYGF33NRC Parts List Firebox Models FPVF33PRA and FPVF33NRA 101357-01 Accessories Perimeter Trim Not Shown Accessory with FireplaceWall Cabinet Mantel and Base Limited Warranty VENT-FREE GAS Fireplace Warranty InformationKeep this Warranty
Top Page Image Contents