Desa VSGF36NRB, VSGF36PTB, VSGF36NTB Hard-wiring Firebox, Installing Fireplace Hood and Screen

Page 18

Installation

Continued

Hard-wiring Firebox

NOTICE: A qualified electrician must connect electrical wiring to duplex outlet for built-in instal- lation. Follow all local codes. In absence of local codes fol- low The National Electric Code ANSI/NFPA 70.

The “Handy Box” with duplex outlet is provided in the firebox located in the lower right base area.

1.Remove screw holding duplex outlet cover to handy box. Remove duplex outlet.

2.Route electrical cable through strain relief and handy box (see Figure 23). Tighten screws on strain relief.

3.Connect electrical cable to duplex outlet. Match wire colors to those on duplex outlet. Be sure to connect the ground wire.

4.Place duplex outlet back into handy box and secure with screws. Replace outlet cover.

Duplex Box/

Handy Box

Screws

Strain Relief

Figure 23 - Hard-Wiring Firebox

INSTALLING FIREPLACE HOOD AND SCREEN

1.Loosen screws inside top edge of firebox. Slide notches in hood over screws and tighten screws (see Figure 24).

2.Install fireplace screen by slipping notches of fireplace screen over screws on front of fireplace (see Figure 25).

Screw

Hood

Figure 24 - Hood Placement

(Model May Vary From Illustration)

Screw

Screen

Figure 25 - Screen Placement

(Model May Vary From Illustration)

18

www.desatech.com

119305-01A

Image 18

Contents What to do if YOU Smell GAS VSGF36NTB, VSGF36PTB, VSGF36NRB and VSGF36PRBTable of Contents Safety InformationSafety Information Local Codes Product Features Product IdentificationUnpacking Product Specifications Locating FireboxPlanning Unusually Tight Construction Air For Combustion VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsInstallation Clearances Minimum Wall and Ceiling Clearances seeBuilt-In Firebox Installation Mantel Clearances for Built-In InstallationRough Opening Dimensions for Built-in Installation Front Width DepthInstalling Firebox Using Optional Accessory MantelsInstalling Gas Piping to Fireplace Location Installation Items Needed Natural GasPropane/LP Connecting Fireplace to Gas Supply Checking Gas Connections,KPa Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections Test Pressures Equal To or Less Than Psig 3.5 kPaInstalling Logs Middle Right Log Middle Left LogHard-wiring Firebox Installing Fireplace Hood and ScreenThermostat Models For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsThermostat Control Operation Manual Lighting ProcedureRemote Control Models To Turn OFF GASSet flame adjustment knob to any level between HI and LO Optional Hand-Held Blower OperationTo Turn OFF GAS To Appliance Remote OperationOn/Off Series Model HRC100 Thermostat Series Model hrc200Pilot Flame Pattern Key Pad Lock FeatureInspecting Burners Main burnerCleaning Maintenance Burner Injector Holder Pilot Air Inlet HoleTechnical Service Wiring Diagram Replacement PartsSpecifications Service HintsTroubleshooting Observed Problem Possible Cause RemedyMaintenance, See Cleaning and Mainte Shut off gas supply Do not try to light any appliance Accessories Illustrated Parts Breakdown Models VSGF36PTB, VSGF36NTBParts List Models VSGF36PRB, VSGF36NRB Parts List Models VSGF36PTB, VSGF36NTB, VSGF36PRB and VSGF36NRB KEY NO. Part no Description 119305-01A 119305-01A Warranty Information Keep this WarrantyLimited Warranty VENT-FREE GAS Fireplace System