Avalon Stoves DVL Insert EF II owner manual Vent Connector Removal and Installation

Page 16

16

Installation (for qualified installers only)

Vent Connector Removal and Installation

The vent connector is shipped attached to the insert, but may be removed to facilitate tight installations. See the directions below for installation.

1.Route the flex vent through the chimney from above (leave an extra 3' at the top). Make sure the flex is thoroughly stretched.

2.Remove the vent connector and attach it to the flex vent (see the instructions on the following page). NOTE: be careful of the anti-seize on the connector – it will stain clothing, etc.

3.Pull on the flex vent until the vent connector is at the same height as the insert. Temporarily attach the flex vent to the top of the chimney (leave extra slack).

4.Slide the insert into place, guiding the vent connector into the guides on top of the insert.

5.Attach the vent connector to the appliance (see the following page for details).

6.Remove any excess slack in the flex line and attach the vent termination.

1

2

2

3

6

5

4

© Travis Industries

4080123

100-01174_002

Image 16
Contents DVL Insert EF Travis Industries, Inc2Introduction Introduction Important InformationSave Your Bill of Sale 4080123Table of Contents Safety Precautions If YOU Smell GASDo not place anything inside Features Installation Options Heating SpecificationsDimensions Natural Gas PropaneInstallation for qualified installers only Top Convection Deflector Fireplace RequirementsLeveling Bolts Hearth RequirementsFactory-Built Metal Wood-Burning Fireplace Requirements Clearances Mantel ClearancesFace Sizing Face Height WidthGas Line Location Gas Line RequirementsGas Inlet Pressure Vent Requirements Altitude ConsiderationsVent Installation Vent RestrictorVent Configurations Inlet & Exhaust Re-Line Vent LocationVent Connector Removal and Installation Vent Connector Removal Installation Without Surround Panels Surround Panel InstallationInstallation of the On/Off Switch and Rheostat Electrical ConnectionFinalizing the Installation Glass Frame Removal and InstallationGlass Log Set Installation Install the logsInstall the twigs, ember chunk, kibbles, and rock wool Installing the Rock WoolAir Shutter Adjustment Steps for Finalizing the InstallationPilot Flame Inspection Fine Tuning the EMBER-FYRE Burner Before You Begin 26OperationLocation of Controls Operation Starting The Pilot FlameAdjusting the Flame Height 28OperationStarting the Heater for the First Time Turning the Heater On and OffAdjusting the Blower Speed Operation29Normal Operating Sounds Normal Operating OdorsYearly Service Procedure 30MaintenanceMaintaining Your Heaters Appearance Maintenance Troubleshooting Table32Maintenance How this Heater WorksWhat Turns the Main Burners On and Off What Prevents Gas BuildupWiring Diagram Maintenance33Replacement Parts List Safety Label Safety LabelLimited 7 Year Warranty Years 1 & 2 Coverage Parts & LaborYears 3 Through 5 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyBurner Replacement LP Conversion InstructionsOptional Equipment for qualified installers only Follow the directions below to replace the orificesTo adjust the pilot flame, turn this screw Note if totally Firebacks Optional Equipment for qualified installers only Important Installation Note for Models Using the Firebacks Accent LightAccent Light Operation Lower Surround Panel Index

DVL Insert EF II specifications

The Avalon Stoves DVL Insert EF II is an impressive addition to any home, combining functionality, efficiency, and aesthetic appeal. Designed to convert traditional wood-burning fireplaces into an efficient heating source, the DVL Insert EF II stands out due to its exceptional engineering and innovative features.

One of the main characteristics of the DVL Insert EF II is its high-efficiency rating. With an impressive efficiency of up to 85%, this insert maximizes heat output while minimizing wood consumption. This translates to fewer trips to the woodpile, allowing homeowners to enjoy extended warmth and comfort during the cold months.

Key technologies incorporated into the DVL Insert EF II include a sophisticated air wash system that keeps the glass clean, ensuring a clear view of the captivating flames. This feature not only enhances the aesthetic appeal of the insert but also reduces the maintenance required to keep the glass sparkling. Additionally, the DVL Insert EF II employs a secondary combustion system that ensures more complete burning of the wood, which increases both efficiency and heat output while reducing smoke emissions.

The DVL Insert EF II comes with a robust firebox, made from high-quality steel, which is designed to withstand high temperatures and offer durability over time. Its large viewing area is framed by a cast-iron door, giving it a timeless and elegant appearance that complements various styles of decor. The insert is available in multiple finishes, allowing homeowners to choose a look that fits their personal style and existing interior.

Another notable feature is the built-in blower system, which helps distribute heat more evenly throughout the room, enhancing comfort. This option can be particularly beneficial in larger spaces, as it allows for better temperature regulation and extends the reach of the warmth generated.

Installation flexibility is also a key characteristic of the DVL Insert EF II. It can be fitted into most standard fireplaces, making it a versatile choice for many homes. Its compact design ensures that it can fit effortlessly into the existing structure while still providing powerful heating capabilities.

In summary, the Avalon Stoves DVL Insert EF II is a highly efficient, aesthetically pleasing option for homeowners looking to upgrade their fireplace capabilities. With advanced technologies such as an air wash system, secondary combustion, and a built-in blower, this insert delivers both convenience and performance, making it an excellent addition to any living space.