Avalon Stoves DVL Insert EF II Installation Without Surround Panels, Surround Panel Installation

Page 18

18

Installation (for qualified installers only)

Installation Without Surround Panels

The insert may be installed without surround panels. Mount the on/off switch and rheostat to the control panel under the burner pan (see “Installation of the On/Off Switch and Rheostat” on page 19).

Surround Panel Installation

PANEL SIZE

WIDTH

HEIGHT

PART #

8" x 10" Rectangular

44-3/16"

33-3/8"

98500606

Arched (8” x 10”)

44-3/16"

33-3/8"

98500608

10” x 13” Rectangular

48-3/16"

36-3/8"

98500607

1Follow the directions below to install the side panels.

a

Pre-thread the holes on the surround

 

panels with the screws included in the

 

surround panel kit.

 

5/16" Nutdriver

b

Line up each side surround panel and insert two screws from the inside to secure in place.

Run the rheostat wires, on/off switch wires, and power cord through the access hole on the insert

2Follow the directions below to install the top panel.

 

 

 

The insulation included with the

 

 

Top Trim

panels may be discarded.

 

 

 

NOTE:

 

 

b

These 3/8"

Top

 

Panel

 

 

stand-offs are

 

 

 

 

 

not required

 

 

 

and may be

flattened.

 

"L" Bracket

 

Slot for on/off

 

switch and hole

a

for rheostat

 

Install the top panel so the

Right Side Trim

 

two tabs insert into the slots

 

on the side panels.

 

Construct the panel trim. Insert one leg of each "L" bracket into the top and side trim piece. Align the trim to form a precise corner, then tighten the two set screws with a small standard screwdriver. Slide the trim over the panels.

Tighten the set screws from the back side with a small standard screwdriver

Top Trim

"L" Bracket

Right Side

Trim

© Travis Industries

4080123

100-01174_002

Image 18
Contents DVL Insert EF Travis Industries, IncSave Your Bill of Sale 2IntroductionIntroduction Important Information 4080123Table of Contents Safety Precautions If YOU Smell GASDo not place anything inside Dimensions Features Installation OptionsHeating Specifications Natural Gas PropaneInstallation for qualified installers only Top Convection Deflector Fireplace RequirementsHearth Requirements Leveling BoltsFactory-Built Metal Wood-Burning Fireplace Requirements Clearances Mantel ClearancesFace Sizing Face Height WidthGas Line Requirements Gas Line LocationGas Inlet Pressure Vent Requirements Altitude ConsiderationsVent Installation Vent RestrictorVent Configurations Inlet & Exhaust Re-Line Vent LocationVent Connector Removal and Installation Vent Connector Removal Installation Without Surround Panels Surround Panel InstallationInstallation of the On/Off Switch and Rheostat Electrical ConnectionFinalizing the Installation Glass Frame Removal and InstallationGlass Log Set Installation Install the logsInstall the twigs, ember chunk, kibbles, and rock wool Installing the Rock WoolSteps for Finalizing the Installation Air Shutter AdjustmentPilot Flame Inspection Fine Tuning the EMBER-FYRE Burner 26Operation Before You BeginLocation of Controls Operation Starting The Pilot FlameStarting the Heater for the First Time Adjusting the Flame Height28Operation Turning the Heater On and OffNormal Operating Sounds Adjusting the Blower SpeedOperation29 Normal Operating Odors30Maintenance Yearly Service ProcedureMaintaining Your Heaters Appearance Maintenance Troubleshooting TableWhat Turns the Main Burners On and Off 32MaintenanceHow this Heater Works What Prevents Gas BuildupMaintenance33 Wiring DiagramReplacement Parts List Safety Label Safety LabelYears 3 Through 5 Coverage Parts & Labor Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyBurner Replacement LP Conversion InstructionsOptional Equipment for qualified installers only Follow the directions below to replace the orificesTo adjust the pilot flame, turn this screw Note if totally Firebacks Optional Equipment for qualified installers only Important Installation Note for Models Using the Firebacks Accent LightAccent Light Operation Lower Surround Panel Index

DVL Insert EF II specifications

The Avalon Stoves DVL Insert EF II is an impressive addition to any home, combining functionality, efficiency, and aesthetic appeal. Designed to convert traditional wood-burning fireplaces into an efficient heating source, the DVL Insert EF II stands out due to its exceptional engineering and innovative features.

One of the main characteristics of the DVL Insert EF II is its high-efficiency rating. With an impressive efficiency of up to 85%, this insert maximizes heat output while minimizing wood consumption. This translates to fewer trips to the woodpile, allowing homeowners to enjoy extended warmth and comfort during the cold months.

Key technologies incorporated into the DVL Insert EF II include a sophisticated air wash system that keeps the glass clean, ensuring a clear view of the captivating flames. This feature not only enhances the aesthetic appeal of the insert but also reduces the maintenance required to keep the glass sparkling. Additionally, the DVL Insert EF II employs a secondary combustion system that ensures more complete burning of the wood, which increases both efficiency and heat output while reducing smoke emissions.

The DVL Insert EF II comes with a robust firebox, made from high-quality steel, which is designed to withstand high temperatures and offer durability over time. Its large viewing area is framed by a cast-iron door, giving it a timeless and elegant appearance that complements various styles of decor. The insert is available in multiple finishes, allowing homeowners to choose a look that fits their personal style and existing interior.

Another notable feature is the built-in blower system, which helps distribute heat more evenly throughout the room, enhancing comfort. This option can be particularly beneficial in larger spaces, as it allows for better temperature regulation and extends the reach of the warmth generated.

Installation flexibility is also a key characteristic of the DVL Insert EF II. It can be fitted into most standard fireplaces, making it a versatile choice for many homes. Its compact design ensures that it can fit effortlessly into the existing structure while still providing powerful heating capabilities.

In summary, the Avalon Stoves DVL Insert EF II is a highly efficient, aesthetically pleasing option for homeowners looking to upgrade their fireplace capabilities. With advanced technologies such as an air wash system, secondary combustion, and a built-in blower, this insert delivers both convenience and performance, making it an excellent addition to any living space.