Avalon Stoves DVL Insert EF II owner manual Fine Tuning the EMBER-FYRE Burner

Page 25

Finalizing the Installation

25

FINE TUNING THE EMBER-FYRE™ BURNER

Each installation is affected by altitude, vent configuration, and fuel quality. Because of this, the restrictor and air shutter may need to be fine tuned to each installation. Follow the hints below to fine- tune the burner for optimum performance and aesthetics.

Restrictor Adjustment:

Only those installations determined to be over-drafting require this adjustment. See the instructions on page 14 for details.

Air Shutter Hints:

For more glow, open the air shutter, however, this will make the flames more blue.

For yellow flames, close the air shutter, however, this may create less glow.

Correct

Lifting Flames

Ghosting Flames

Flickering Flames

 

Burner Ports

 

 

Burner

(holes)

 

 

The flames should burn right off the top of the burner ports (if they are too blue, adjust the air control).

Lifting flames indicate insufficient draft (restrictor is set too high).

Ghosting flames indicate

Flickering, short flames

insufficient air (restrictor set too

indicate excessive draft

high, air shutter shut down, or

(move air shutter to a higher

other venting error).

position).

Warning: If the vent configuration is installed incorrectly the vent may cause the flames inside the heater to lift or “ghost” – a dangerous situation. Inspect the flames after installation to insure proper performance. If the vent configuration is correct, yet the flames are lifting or ghosting, shut off gas to the heater and contact the dealer for information on remedying the problem.

8.Replace the glass.

9.Attach the face following the directions included with the face.

NOTE: If using the Classic Arched, Artisan, Metropolitan or Victorian Lace Face you must use the face mounting brackets included with the heater (SKU 225-20054). See page 11 for details.

10.Turn the flame adjust knob to its highest position - the flames should not contact the top of the firebox. Check the flame on low position. The flames should burn off of each burner hole. If the heater does not work correctly, contact your dealer for a remedy.

New Brackets

Old Brackets

11. Give this manual to the home owner and fully explain the operation of this heater.

© Travis Industries

4080123

100-01174_002

Image 25
Contents Travis Industries, Inc DVL Insert EFIntroduction Important Information 2IntroductionSave Your Bill of Sale 4080123Table of Contents If YOU Smell GAS Safety PrecautionsDo not place anything inside Heating Specifications Features Installation OptionsDimensions Natural Gas PropaneInstallation for qualified installers only Fireplace Requirements Top Convection DeflectorLeveling Bolts Hearth RequirementsFactory-Built Metal Wood-Burning Fireplace Requirements Mantel Clearances ClearancesFace Height Width Face SizingGas Line Location Gas Line RequirementsGas Inlet Pressure Altitude Considerations Vent RequirementsVent Restrictor Vent InstallationVent Location Vent Configurations Inlet & Exhaust Re-LineVent Connector Removal and Installation Vent Connector Removal Surround Panel Installation Installation Without Surround PanelsElectrical Connection Installation of the On/Off Switch and RheostatGlass Frame Removal and Installation Finalizing the InstallationGlass Install the logs Log Set InstallationInstalling the Rock Wool Install the twigs, ember chunk, kibbles, and rock woolAir Shutter Adjustment Steps for Finalizing the InstallationPilot Flame Inspection Fine Tuning the EMBER-FYRE Burner Before You Begin 26OperationLocation of Controls Starting The Pilot Flame Operation28Operation Adjusting the Flame HeightStarting the Heater for the First Time Turning the Heater On and OffOperation29 Adjusting the Blower SpeedNormal Operating Sounds Normal Operating OdorsYearly Service Procedure 30MaintenanceMaintaining Your Heaters Appearance Troubleshooting Table MaintenanceHow this Heater Works 32MaintenanceWhat Turns the Main Burners On and Off What Prevents Gas BuildupWiring Diagram Maintenance33Replacement Parts List Safety Label Safety LabelYears 1 & 2 Coverage Parts & Labor Limited 7 Year WarrantyYears 3 Through 5 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyLP Conversion Instructions Burner ReplacementFollow the directions below to replace the orifices Optional Equipment for qualified installers onlyTo adjust the pilot flame, turn this screw Note if totally Firebacks Optional Equipment for qualified installers only Accent Light Important Installation Note for Models Using the FirebacksAccent Light Operation Lower Surround Panel Index

DVL Insert EF II specifications

The Avalon Stoves DVL Insert EF II is an impressive addition to any home, combining functionality, efficiency, and aesthetic appeal. Designed to convert traditional wood-burning fireplaces into an efficient heating source, the DVL Insert EF II stands out due to its exceptional engineering and innovative features.

One of the main characteristics of the DVL Insert EF II is its high-efficiency rating. With an impressive efficiency of up to 85%, this insert maximizes heat output while minimizing wood consumption. This translates to fewer trips to the woodpile, allowing homeowners to enjoy extended warmth and comfort during the cold months.

Key technologies incorporated into the DVL Insert EF II include a sophisticated air wash system that keeps the glass clean, ensuring a clear view of the captivating flames. This feature not only enhances the aesthetic appeal of the insert but also reduces the maintenance required to keep the glass sparkling. Additionally, the DVL Insert EF II employs a secondary combustion system that ensures more complete burning of the wood, which increases both efficiency and heat output while reducing smoke emissions.

The DVL Insert EF II comes with a robust firebox, made from high-quality steel, which is designed to withstand high temperatures and offer durability over time. Its large viewing area is framed by a cast-iron door, giving it a timeless and elegant appearance that complements various styles of decor. The insert is available in multiple finishes, allowing homeowners to choose a look that fits their personal style and existing interior.

Another notable feature is the built-in blower system, which helps distribute heat more evenly throughout the room, enhancing comfort. This option can be particularly beneficial in larger spaces, as it allows for better temperature regulation and extends the reach of the warmth generated.

Installation flexibility is also a key characteristic of the DVL Insert EF II. It can be fitted into most standard fireplaces, making it a versatile choice for many homes. Its compact design ensures that it can fit effortlessly into the existing structure while still providing powerful heating capabilities.

In summary, the Avalon Stoves DVL Insert EF II is a highly efficient, aesthetically pleasing option for homeowners looking to upgrade their fireplace capabilities. With advanced technologies such as an air wash system, secondary combustion, and a built-in blower, this insert delivers both convenience and performance, making it an excellent addition to any living space.