Avalon Stoves DVL Insert EF II To adjust the pilot flame, turn this screw Note if totally

Page 38

38

Optional Equipment (for qualified installers only)

5Install the logs and embers.

6Replace glass and face.

7Remove the regulator from the front of the gas control valve. Replace with the propane regulator, using the new gasket and screws included with the regulator. NOTE:

Leak test this area after the heater is installed, gas is connected, and the main burner is lit.

a

Remove and discard the three screws using a slotted screwdriver of Torx T-20.

Slotted

Screwdriver

(or T-20 Torx)

c

Install the LP regulator. Use the screws included with the LP regulator. Tighten to approximately 25 Lbs. torque.

Slotted

Screwdriver

(or T-20 Torx)

b

Remove and discard the regulator, diaphram, spring and center post.

NOTE: Make sure the regulator gasket is correctly aligned before installation.

d

Place the LP label on the base near the gas control valve.

8Make the gas line connection, bleed the gas line (if applicable), start the heater and thoroughly leak-test all gas connections and the gas control valve. Check the pilot. Adjust if necessary.

WARNING:

When lighting or re-lighting the pilot, the glass must be removed (see page 20).

To adjust the pilot flame, turn this screw (NOTE: if totally

 

 

The pilot flame must contact the thermocouple and

unscrewed gas will come out of this port). Clockwise

 

 

thermopile (see the illustration below). Adjust the pilot up or

lowers the flame while counter-clockwise raises it.

Standard

down as necessary.

 

 

 

 

 

Screwdriver

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

© Travis Industries

4080123

100-01174_002

Image 38
Contents DVL Insert EF Travis Industries, IncSave Your Bill of Sale 2IntroductionIntroduction Important Information 4080123Table of Contents Safety Precautions If YOU Smell GASDo not place anything inside Dimensions Features Installation OptionsHeating Specifications Natural Gas PropaneInstallation for qualified installers only Top Convection Deflector Fireplace RequirementsFactory-Built Metal Wood-Burning Fireplace Requirements Hearth RequirementsLeveling Bolts Clearances Mantel ClearancesFace Sizing Face Height WidthGas Inlet Pressure Gas Line RequirementsGas Line Location Vent Requirements Altitude ConsiderationsVent Installation Vent RestrictorVent Configurations Inlet & Exhaust Re-Line Vent LocationVent Connector Removal and Installation Vent Connector Removal Installation Without Surround Panels Surround Panel InstallationInstallation of the On/Off Switch and Rheostat Electrical ConnectionFinalizing the Installation Glass Frame Removal and InstallationGlass Log Set Installation Install the logsInstall the twigs, ember chunk, kibbles, and rock wool Installing the Rock WoolPilot Flame Inspection Steps for Finalizing the InstallationAir Shutter Adjustment Fine Tuning the EMBER-FYRE Burner Location of Controls 26OperationBefore You Begin Operation Starting The Pilot FlameStarting the Heater for the First Time Adjusting the Flame Height28Operation Turning the Heater On and OffNormal Operating Sounds Adjusting the Blower SpeedOperation29 Normal Operating OdorsMaintaining Your Heaters Appearance 30MaintenanceYearly Service Procedure Maintenance Troubleshooting TableWhat Turns the Main Burners On and Off 32MaintenanceHow this Heater Works What Prevents Gas BuildupReplacement Parts List Maintenance33Wiring Diagram Safety Label Safety LabelYears 3 Through 5 Coverage Parts & Labor Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyBurner Replacement LP Conversion InstructionsOptional Equipment for qualified installers only Follow the directions below to replace the orificesTo adjust the pilot flame, turn this screw Note if totally Firebacks Optional Equipment for qualified installers only Important Installation Note for Models Using the Firebacks Accent LightAccent Light Operation Lower Surround Panel Index

DVL Insert EF II specifications

The Avalon Stoves DVL Insert EF II is an impressive addition to any home, combining functionality, efficiency, and aesthetic appeal. Designed to convert traditional wood-burning fireplaces into an efficient heating source, the DVL Insert EF II stands out due to its exceptional engineering and innovative features.

One of the main characteristics of the DVL Insert EF II is its high-efficiency rating. With an impressive efficiency of up to 85%, this insert maximizes heat output while minimizing wood consumption. This translates to fewer trips to the woodpile, allowing homeowners to enjoy extended warmth and comfort during the cold months.

Key technologies incorporated into the DVL Insert EF II include a sophisticated air wash system that keeps the glass clean, ensuring a clear view of the captivating flames. This feature not only enhances the aesthetic appeal of the insert but also reduces the maintenance required to keep the glass sparkling. Additionally, the DVL Insert EF II employs a secondary combustion system that ensures more complete burning of the wood, which increases both efficiency and heat output while reducing smoke emissions.

The DVL Insert EF II comes with a robust firebox, made from high-quality steel, which is designed to withstand high temperatures and offer durability over time. Its large viewing area is framed by a cast-iron door, giving it a timeless and elegant appearance that complements various styles of decor. The insert is available in multiple finishes, allowing homeowners to choose a look that fits their personal style and existing interior.

Another notable feature is the built-in blower system, which helps distribute heat more evenly throughout the room, enhancing comfort. This option can be particularly beneficial in larger spaces, as it allows for better temperature regulation and extends the reach of the warmth generated.

Installation flexibility is also a key characteristic of the DVL Insert EF II. It can be fitted into most standard fireplaces, making it a versatile choice for many homes. Its compact design ensures that it can fit effortlessly into the existing structure while still providing powerful heating capabilities.

In summary, the Avalon Stoves DVL Insert EF II is a highly efficient, aesthetically pleasing option for homeowners looking to upgrade their fireplace capabilities. With advanced technologies such as an air wash system, secondary combustion, and a built-in blower, this insert delivers both convenience and performance, making it an excellent addition to any living space.