Regency U39-NG, U39-LP installation manual DURA-VENT Termination KIT, DURA-VENT Venting Components

Page 15

INSTALLATION

DURA-VENT

TERMINATION KIT

Planning Your Dura-Vent

Installation

There are two basic types of Dura-Vent Direct Vent System installations: horizontal termina- tion and vertical termination. Confirm the max- imum horizontal run and maximum vertical rise from the diagrams on pages 8-13.

When planning your installation, it will be nec- essary to select the proper length of vent pipe for your particular requirements. For horizontal installations, determine the minimum clearance from the rear of the unit to the wall. It is also important to note the wall thickness. (The wall thimble is suitable for 2 x 4 or 2 x 6 wall construction.) Select the amount of vertical rise desired for "vertical-to-horizontal" type instal- lations.

Warning: Always maintain required clear- ances (air spaces) to nearby combusti- bles to prevent a fire hazard. Do not fill air spaces with insulation.

The minimum clearance requirements between the outer wall of the vent pipe and nearby combustible surfaces is 1-1/4 inch. Be sure to check the vent termination clearance require- ments from decks, windows, soffits, gas reg- ulators, air supply inlets and public walkways as specified in the Exterior Vent Terminal Loca- tions on page 8 and in your local building codes.

Note: These are the minimum pieces required. Other parts may be re- quired for your particular instal- lation. See page 13 for a list of vent parts.

If installing termination on a siding covered wall, a vinyl siding standoff or furring strips can be used in order to ensure that the termination is not recessed into siding.

The vinyl siding standoff is required for walls with vinyl siding.

Minimum components for a Dura-Vent Horizontal

Installation:

A)Dura-Vent Horizontal Termination Kit

B)Wall Thimble (required for combus- tible walls)

Minimum components for a Dura-Vent Vertical Termination:

C)Dura-Vent Vertical Termination Kit See page 12 for pipe lengths.

The Simpson Dura-Vent Direct Vent System offers a complete line of component parts for installation of both horizontal and vertical instal- lation. Many items are offered in decorative black, as well as galvanized finish. The galva- nized pipe and fittings are used for concealed locations such as attics or where corrosion is a factor, such as above the roof line. Decora- tive brass trim kits are available for both wall thimbles and ceiling support boxes.

Part # Description

971Horiz. Termination Kit includes: 90o black elbow, wall thimble cover,

horiz. square termination cap, 24" black pipe, 11" -14" 5/8" adjustable black pipe

970Basic Horiz. Termination Kit includes: 90o black elbow, wall

thimble cover, horiz. square termination cap

978Vert. Termination Kit includes 0/12 - 6/12 pitch adjustable flashing, storm collar, low profile

term. cap

908B 6" Pipe Length-Black

907B 9" Pipe Length-Black

90612" Pipe Length Galv.

906B 12" Pipe Length-Black

90424" Pipe Length Galv.

904B 24" Pipe Length-Black

90336" Pipe Length Galv.

903B 36" Pipe Length-Black

90248" Pipe Length Galv.

902B 48" Pipe Length-Black

To determine the length of vent pipe required for vertical installations, measure the distance from the unit flue outlet to the ceiling, the ceiling thickness, the vertical rise in an attic or second storey, and allow for sufficient vertical height above the roof line.

For multi-storey applications, fire stops are required at each floor level. If an offset is needed, additional pipe, elbows and supports will be required.

DURA-VENT VENTING

COMPONENTS

You will require the following components with your new Regency Direct Vent Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer.

Dura-Vent Basic

Horizontal Kit # 970

1 90o Elbow

1 Wall Thimble Cover

1 Horiz. Sq. Term. Cap

Alternate Horizontal

Termination Caps

The Regency AstroCapTM is certified for installations using FPI venting systems as well as Simpson Dura-Vent® and Direct Vent GS.

RegencyTM, and Regency AstroCapTM are the proprietary trademarks of FPI Fireplace Products International Ltd.

Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

Regency U39 ULTIMATE Direct Vent Freestanding Gas Stove

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Ultimate U39 Regency Unit SpecificationsTable of Contents Copy of Safety Label for U39 Gas Stove Safety LabelInformation for Mobile InstallationSpecifications Save These InstructionsGeneral Safety Information Installation ChecklistClearances to Combustibles Locating Your Ultimate GAS Stove Louver InstallationInstallation Precautions Venting IntroductionExterior Vent Terminal 4DT-AJB Rigid Pipe Venting Components ListAlternate Horizontal Termination Caps Rigid Pipe Venting SystemsVent Restrictor Position Safety Precautions for the InstallerRigid Pipe Venting Arrangements Horizontal Terminations for All Venting SystemsVertical Venting with Two 2 90o Elbows Horizontal Venting with Two 2 90o ElbowsSions on pages 8 to DV Stove Horizontal Vent KITQty. Description OptionalBrick, concrete, or other types of sidings Dismantle all pipe sections including vent terminalDURA-VENT Venting Components Planning Your Dura-Vent InstallationMinimum components for a Dura-Vent Horizontal Installation DURA-VENT Termination KITSnorkel Terminations DURA-VENT Horizontal InstallationsBelow Grade Installation Cathedral Ceilings Offset ChartSupport Extensions Round Rdse or Square Sqse GeneralConverting a Factory Built Metal Chimney Converting a Masonry Chimney System Data GAS ConnectionHigh Elevation System Data U39 with 40,000 BTUConversion from Natural GAS to Propane Pilot assembly is now accessible for stepsGAS Pipe Pressure Testing Conversion to Lower BTU RatingValve Description U39 with 30,000 Btu/h Aeration AdjustmentLOG SET Installation U39 with 38,000 Btu/hPackaged separately Front Door InstallationWiring Optional Remote ControlOptional Wall Thermostat Operating Instructions Copy of the Lighting Plate instructions Adjusting Flame HeightNormal Operating Sounds GAS Appliances Automatic Convection FAN OperationGOLD-PLATED Doors MaintenanceMaintenance Instructions General Vent MaintenanceDoor Gasket LOG ReplacementLatch Adjustment Glass ReplacementReplacing U39 Fan FAN MaintenanceAlternate Fan Access To remove U39 fanRemoving Valve Parts List U39 Main AssemblyDescription U39 Burner & LOG Assembly U39 Door Assemblies Regency U39 Ultimate Direct Vent Freestanding Gas Stove Regency U39 Ultimate Direct Vent Freestanding Gas Stove Regency U39 Ultimate Direct Vent Freestanding Gas Stove Conditions WarrantyInstaller Please complete the following information

U39-NG, U39-LP specifications

The Regency U39-LP and U39-NG are modern gas fireplaces designed to enhance the aesthetic appeal and functionality of any space while delivering exceptional performance. These units are part of Regency's commitment to innovation and sustainability, providing homeowners with an efficient heating solution that seamlessly integrates into various home styles.

One of the standout features of the U39 series is its versatility in fuel options. The U39-LP operates on liquid propane, while the U39-NG utilizes natural gas. This flexibility allows homeowners to choose the best option suited for their existing infrastructure and personal preferences. Both models are designed to deliver efficient heating with an impressive BTU output, ensuring that rooms stay warm and comfortable during colder months.

The U39 series is equipped with cutting-edge technologies, including a state-of-the-art control system that allows users to easily adjust the flame height and heat output. This feature not only enhances user convenience but also promotes energy efficiency by allowing adjustments based on real-time heating needs. The inclusion of an optional remote control further simplifies the operation, enabling users to manage their fireplace from anywhere in the room.

Another remarkable aspect of the Regency U39-LP and U39-NG is the clean, contemporary design. The linear shape and large viewing area provide an unobstructed view of the flames, adding a stunning focal point to any living space. The customizable options for finishes and surround materials mean that homeowners can tailor the fireplace to perfectly match their décor, whether it be modern, traditional, or somewhere in between.

Safety is a top priority for Regency, and the U39 series includes multiple safety features to ensure peace of mind. An integrated safety shut-off system is designed to automatically turn off the unit in case of emergencies, while tempered glass doors protect against accidental burns.

In summary, the Regency U39-LP and U39-NG gas fireplaces embody a blend of functionality, beauty, and safety. With their high thermal efficiency, user-friendly technologies, and elegant design, these fireplaces are an ideal choice for anyone looking to elevate their home heating experience while enjoying the charm of a glowing fire. Whether it's for a cozy gathering with family or a quiet evening alone, the U39 series stands out as a stylish solution with exceptional performance.
Top Page Image Contents