Regency L900-NG, L900-LP installation manual Pilot Shield, Clip, Cable Tie, J9 Jumper

Page 33

INSTALLATION

25)Remove the pilot shield by removing the 2 screws.

Pilot

Shield

26)Remove the clip from the pilot head assembly using a flat head screw driver.

Clip

27)Remove the NG pilot orifice with the Allen Key and replace with LP pilot orifice.

28)Re-install the pilot head and pilot shield.

29)Using a Torx T20, remove and discard the 3 pressure regulator mounting screws. Remove the modulator coil and the gasket.

30)Ensure that the new rubber gasket (supplied with coil) is properly positioned and install the new modulating pressure regulator assem- bly to the valve using the screws supplied with the kit. Tighten screws securely.

31)Install the enclosed identification label to the valve body where it can be easily seen.

32)Attach the LP conversion decal near or on top of the serial no. decal.

33)Replace yellow "Natural Gas" label with red "Propane" label.

34)Re-install valve tray and all electrical connections to the valve and solenoid valve.

35)Cut the cable tie that holds the wires connected to the Control Module and pull out.

Note: An extra cable tie is included with the LP Kit for re-installation.

Cable Tie

Control Module

 

36)Remove the J9 jumper using needle nose pliers.

J9 Jumper

37)Re-install the control module.

38)Re-install the base brick panel.

39)Re-install the rear log support bracket.

40)Plug in the power source.

41)Re-install the left heat shield.

42)Install the interior brick panels.

43)Adjust the burner aeration settings to the LP settings and install the burners.

Front Burner

1/4"

Rear Burner

3/8"

44)Re-install the grate.

45)Turn on the gas supply and check for gas leaks.

46)Install the log set.

47)Re-install the glass door.

48)Check the inlet and outlet pressures.

49)Re-install the right heat shield.

50)Check operation of flame control using the remote control. Refer to FireWizard operation manual for details.

51)Check for proper flame appearance.

52)Install the exterior brick panels.

INSTALLATION

Installer Notice:

This instructions must be left with the appliance.

J9 Jumper Location

Regency® L900 Direct Vent Gas Fireplace

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Libertytm L900 Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Decal Safety LabelListed Vented GAS Fireplace Heater Certified for / Certifiée pour Canada and U.S.AMA Code CO Detector RequirementsUnit Dimensions General Safety Information InstallationInstallation Checklist Important Message Save These InstructionsHearth Requirements Heat Release KITManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Mantel LEG Clearances Mantel ClearancesDiagram Framing & FinishingMaterial Prior to Installation Unit AssemblyVent Restrictor Position Venting IntroductionLatch Location Vent Restrictor Plate= Clearance to permanently closed window *min /30cm Exterior Vent Termination RequirementsVenting Arrangements Horizontal Termination FlexFPI Kit # Length Contains Basic Horizontal & Vertical Terminations Rigid Pipe Venting Systems58DVA-16AB 8 Rigid Pipe Cross Reference ChartL676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Vent Restrictor SettingHorizontal Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o Elbows Allowable Vertical Terminations Unit Installation with Horizontal Termination This allows for small adjustments Unit Installation With Vertical TerminationDiagram Minimum VentAstrocap XL Unit InstallationL900-NG System Data GAS LineL900-LP System Data SIT 825 Valve DescriptionHinge Door Heat Shield Power Module BACK-UP Battery InstallationPower Module Heat Shield Latch LocationLP Conversion Kit Contains Qty Description Conversion KIT #546-969 from NG to LPUsing a flat head screw driver Pilot Shield HeatClip Heat Shield J9 Jumper Location Hinge Door Unplug the power sourceHeat Shield Bracket Heat ShieldBottom Brick Panel Modulating Coil WiresValve Tray Valve Tray Slightly RemovedClip Pilot ShieldCable Tie J9 JumperHandle with care. do not Force Into Position Brick Panel InstallationTop Brick Panel F t Side Brick Panel Back Brick PanelOuterbox of Firebox Right Side Brick PanelLOG SET Installation 03-4203-42 03-41 Burner Tube 03-4303-44 03-45 03-41 03-43Wiring Diagram Aeration AdjustmentOperating Instructions Lighting ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsShutdown Procedure Operation During Power OutageNormal Operating Sounds GAS Appliances Copy of Lighting Plate Instructions STOP! Read the safety information above on this labelMaintenance BACK-UP Battery Replacement Heat ShieldBracket Hinge Heat Door Bracket Heat Shield Power Module ReplacementControl Module Replacement Bracket Hinge HeatControl Module DC Sparker Replacement Battery CoverHeat Shield Replace the DC sparker Unplug the power source Valve Tray ReplacementBottom Brick Panel WiresModulating Coil Valve Tray Slightly Removed Valve TrayParts List Main AssemblyDescription Parts List Burner & LOG Assembly Regency L900 Direct Vent Gas Fireplace Regency L900 Direct Vent Gas Fireplace Regency L900 Direct Vent Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information

L900-LP, L900-NG specifications

The Regency L900-NG and L900-LP are remarkable gas fireplaces that epitomize both elegance and efficiency, bringing a blend of modern technology and traditional aesthetics to any living space. Designed for versatility, these units are suitable for homes with natural gas (NG) or propane (LP) gas lines, thus catering to a wide range of customer preferences.

One of the standout features of the L900 series is its impressive heating capacity. With up to 30,000 BTUs, these fireplaces can efficiently warm large areas, making them an exceptional choice for both residential and commercial settings. Their exceptional airflow and heat distribution ensure that users enjoy a cozy ambience throughout the space.

The L900 models are integrated with cutting-edge technology that enhances user experience. The advanced electronic ignition ensures reliable start-ups, while the variable flame height adjustment provides flexibility, allowing users to customize the heat output according to their needs. The inclusion of an optional remote control system adds an extra layer of convenience, enabling homeowners to operate the fireplace from anywhere in the room.

Aesthetic appeal is also a major highlight of the Regency L900 series. The full-view glass front maximizes the viewing area, allowing users to enjoy the mesmerizing flames fully. The sleek, contemporary design can easily complement various interior styles, from modern to traditional settings. Moreover, with several customizable options, including media choices such as glass, pebbles, or logs, users can personalize their fireplace to suit their decor.

Safety is always a priority with Regency products. The L900 models come equipped with a safety shut-off valve that activates in case of any irregularities, providing peace of mind for users. Additionally, the fireplace’s direct venting system ensures that combustion gases are safely expelled outside, allowing for effective ventilation without compromising indoor air quality.

Durability is another significant characteristic of the Regency L900 series. Constructed from high-quality materials, these fireplaces promise longevity and resilience, ensuring they can withstand the test of time.

Overall, the Regency L900-NG and L900-LP gas fireplaces stand out for their combination of performance, efficiency, and style. With their advanced features, customizable options, and focus on safety, they provide an enticing heating solution for any home or business, merging warmth with a touch of elegance.
Top Page Image Contents