Regency L900-NG, L900-LP installation manual Vertical Venting with Three 3 90o Elbows

Page 21

Vertical Venting with Three (3) 90o Elbows

One 90o elbow = Two 45o elbows.

Option

V

H + H1

V + V1

With these options, max.

A)

2' Min.

3' Max.

4' Min.

 

 

 

 

total pipe length is 30 feet

B)

3' Min.

4' Max.

6' Min.

with min. of 10 feet total

C)

4' Min.

5' Max.

8' Min.

vertical and max. 8 feet

D)

5' Min.

6' Max.

9' Min.

total horizontal.

E)

6' Min.

8' Max.

10' Min.

Please note min. 1 foot

 

 

 

 

VENT RESTRICTOR SETTING:

between 90o elbows is

Vent restrictor at 0" - factory set, no

required.

adjustment required.

 

 

INSTALLATION

INSTALLATION

Regency® L900 Direct Vent Gas Fireplace

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Libertytm L900 Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Decal Safety LabelListed Vented GAS Fireplace Heater Certified for / Certifiée pour Canada and U.S.AMA Code CO Detector RequirementsUnit Dimensions General Safety Information InstallationInstallation Checklist Important Message Save These InstructionsHearth Requirements Heat Release KITManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Mantel LEG Clearances Mantel ClearancesDiagram Framing & FinishingMaterial Prior to Installation Unit AssemblyVent Restrictor Position Venting IntroductionLatch Location Vent Restrictor Plate= Clearance to permanently closed window *min /30cm Exterior Vent Termination RequirementsVenting Arrangements Horizontal Termination FlexFPI Kit # Length Contains Basic Horizontal & Vertical Terminations Rigid Pipe Venting Systems58DVA-16AB 8 Rigid Pipe Cross Reference Chart L676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Vent Restrictor SettingHorizontal Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o Elbows Allowable Vertical Terminations Unit Installation with Horizontal Termination This allows for small adjustments Unit Installation With Vertical TerminationDiagram Minimum VentAstrocap XL Unit InstallationL900-NG System Data GAS LineL900-LP System Data SIT 825 Valve DescriptionHinge Door Heat Shield Power Module BACK-UP Battery InstallationPower Module Heat Shield Latch LocationLP Conversion Kit Contains Qty Description Conversion KIT #546-969 from NG to LPUsing a flat head screw driver Pilot Shield HeatClip Heat Shield J9 Jumper Location Hinge Door Unplug the power sourceHeat Shield Bracket Heat ShieldBottom Brick Panel Modulating Coil WiresValve Tray Valve Tray Slightly RemovedClip Pilot ShieldCable Tie J9 JumperHandle with care. do not Force Into Position Brick Panel InstallationTop Brick Panel F t Side Brick Panel Back Brick PanelOuterbox of Firebox Right Side Brick PanelLOG SET Installation 03-4203-42 03-41 Burner Tube 03-4303-44 03-45 03-41 03-43Wiring Diagram Aeration AdjustmentOperating Instructions Lighting ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsShutdown Procedure Operation During Power OutageNormal Operating Sounds GAS Appliances Copy of Lighting Plate Instructions STOP! Read the safety information above on this labelMaintenance BACK-UP Battery Replacement Heat ShieldBracket Hinge Heat Door Bracket Heat Shield Power Module ReplacementControl Module Replacement Bracket Hinge HeatControl Module DC Sparker Replacement Battery CoverHeat Shield Replace the DC sparker Unplug the power source Valve Tray ReplacementBottom Brick Panel WiresModulating Coil Valve Tray Slightly Removed Valve TrayParts List Main AssemblyDescription Parts List Burner & LOG Assembly Regency L900 Direct Vent Gas Fireplace Regency L900 Direct Vent Gas Fireplace Regency L900 Direct Vent Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information
Top Page Image Contents