Regency L900-NG Venting Introduction, Vent Restrictor Position, Latch Location, Hinge Door

Page 13

INSTALLATION

VENTING

INTRODUCTION

The L900 uses the "balanced fl ue" technology Co Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These flue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

VENT RESTRICTOR

POSITION

To set the vent restriction as indicated in the venting arrangements diagrams, refer to the instructions below;

1)Remove the glass door.

a.Release the 2 door latches on the left and right side at the top of the fi rebox.

Latch Location

Latch

Screws for plugging the holes.

(all holes must be plugged with a screw).

Screw holes for fi xing the restrictor plate.

Factory Set Vent Restrictor Setting

(no adjustment required)

INSTALLATION

Vent restriction is required for certain venting installations, see the diagrams in the "Venting Arrangements" section to determine if they are required for your installation.

The Vent Restrictor plate is located on the inside top of the fi rebox.

Vent Restrictor Plate

b.Swingthedooroutfromthetopandrelease the hinges on the left and right side of the door by lifting them up.

Hinge

Door

2)Remove the screws that hold the vent restric- tor plate in place.

3)Adjust the vent restrictor plate to the required vent restrictor position as per the diagrams shown.

4)Once the vent restrictor plate is in the required position, secure with screws.

Regency® L900 Direct Vent Gas Fireplace

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Libertytm L900 Gas Fireplace Information for MOBILE/MANUFACTURED Homes After First Sale Manufactured Mobile Home RequirementsTable of Contents Copy of Safety Decal Safety LabelListed Vented GAS Fireplace Heater Certified for / Certifiée pour Canada and U.S.AMA Code CO Detector RequirementsUnit Dimensions General Safety Information InstallationInstallation Checklist Important Message Save These InstructionsHearth Requirements Heat Release KITManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Mantel LEG Clearances Mantel ClearancesFraming & Finishing DiagramMaterial Prior to Installation Unit AssemblyVent Restrictor Position Venting IntroductionLatch Location Vent Restrictor Plate= Clearance to permanently closed window *min /30cm Exterior Vent Termination RequirementsHorizontal Termination Flex Venting ArrangementsFPI Kit # Length Contains Basic Horizontal & Vertical Terminations Rigid Pipe Venting Systems58DVA-16AB 8 Rigid Pipe Cross Reference ChartL676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Vent Restrictor SettingHorizontal Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o Elbows Allowable Vertical Terminations Unit Installation with Horizontal Termination This allows for small adjustments Unit Installation With Vertical TerminationDiagram Minimum VentAstrocap XL Unit InstallationL900-NG System Data GAS LineL900-LP System Data SIT 825 Valve DescriptionHinge Door Heat Shield Power Module BACK-UP Battery InstallationPower Module Heat Shield Latch LocationLP Conversion Kit Contains Qty Description Conversion KIT #546-969 from NG to LPPilot Shield Heat Using a flat head screw driverClip Heat Shield J9 Jumper Location Hinge Door Unplug the power sourceHeat Shield Bracket Heat ShieldBottom Brick Panel Modulating Coil WiresValve Tray Valve Tray Slightly RemovedClip Pilot ShieldCable Tie J9 JumperHandle with care. do not Force Into Position Brick Panel InstallationTop Brick Panel F t Side Brick Panel Back Brick PanelOuterbox of Firebox Right Side Brick Panel03-42 LOG SET Installation03-42 03-41 Burner Tube 03-4303-44 03-45 03-41 03-43Wiring Diagram Aeration AdjustmentOperating Instructions Lighting ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsOperation During Power Outage Shutdown ProcedureNormal Operating Sounds GAS Appliances Copy of Lighting Plate Instructions STOP! Read the safety information above on this labelMaintenance Heat Shield BACK-UP Battery ReplacementBracket Hinge Heat Door Bracket Heat Shield Power Module ReplacementBracket Hinge Heat Control Module ReplacementControl Module Battery Cover DC Sparker ReplacementHeat Shield Replace the DC sparker Unplug the power source Valve Tray ReplacementBottom Brick Panel WiresModulating Coil Valve Tray Slightly Removed Valve TrayMain Assembly Parts ListDescription Parts List Burner & LOG Assembly Regency L900 Direct Vent Gas Fireplace Regency L900 Direct Vent Gas Fireplace Regency L900 Direct Vent Gas Fireplace Warranty Limited Lifetime WarrantyInstaller Please complete the following information

L900-LP, L900-NG specifications

The Regency L900-NG and L900-LP are remarkable gas fireplaces that epitomize both elegance and efficiency, bringing a blend of modern technology and traditional aesthetics to any living space. Designed for versatility, these units are suitable for homes with natural gas (NG) or propane (LP) gas lines, thus catering to a wide range of customer preferences.

One of the standout features of the L900 series is its impressive heating capacity. With up to 30,000 BTUs, these fireplaces can efficiently warm large areas, making them an exceptional choice for both residential and commercial settings. Their exceptional airflow and heat distribution ensure that users enjoy a cozy ambience throughout the space.

The L900 models are integrated with cutting-edge technology that enhances user experience. The advanced electronic ignition ensures reliable start-ups, while the variable flame height adjustment provides flexibility, allowing users to customize the heat output according to their needs. The inclusion of an optional remote control system adds an extra layer of convenience, enabling homeowners to operate the fireplace from anywhere in the room.

Aesthetic appeal is also a major highlight of the Regency L900 series. The full-view glass front maximizes the viewing area, allowing users to enjoy the mesmerizing flames fully. The sleek, contemporary design can easily complement various interior styles, from modern to traditional settings. Moreover, with several customizable options, including media choices such as glass, pebbles, or logs, users can personalize their fireplace to suit their decor.

Safety is always a priority with Regency products. The L900 models come equipped with a safety shut-off valve that activates in case of any irregularities, providing peace of mind for users. Additionally, the fireplace’s direct venting system ensures that combustion gases are safely expelled outside, allowing for effective ventilation without compromising indoor air quality.

Durability is another significant characteristic of the Regency L900 series. Constructed from high-quality materials, these fireplaces promise longevity and resilience, ensuring they can withstand the test of time.

Overall, the Regency L900-NG and L900-LP gas fireplaces stand out for their combination of performance, efficiency, and style. With their advanced features, customizable options, and focus on safety, they provide an enticing heating solution for any home or business, merging warmth with a touch of elegance.
Top Page Image Contents