PB Heat Gas Boiler manual Status Menu Description Code, Installer Menu Parameter Function

Page 31

ELECTRICAL

4.Error Codes: The LED Display will display error codes if the boiler is in a temporary fault condition. Table 8.1 shows Error Codes and descriptions. In some cases, if the temporary fault is not corrected within 60 seconds the controller will go into a Fault Code.

5.Fault Codes: A Fault Code indicates the controller is locked-out. Press the S4 "Reset" button to resume operation after repairing the problem. Table 8.2 shows Fault Codes for this control.

6.Status Menu: The status menu, as shown in Table 6.3, allows the installer to display the current boiler supply (outlet) temperature, return (inlet temperature), fan speed, flame signal (µA), boiler circulator status, boiler set point, total power on hours, boiler on hours, and the number of cycles.

a.To access this menu press and hold the S4 "Reset" key on the display module for 3 seconds.

b.The display will alternate between "d1" and the value of the supply temperature.

c.To scroll through the other status codes, simply press S4 "Reset", again.

d.To exit this menu, press the S3 "Program" key.

Table 6.3: Status Menu

Status

Description

Code

 

 

 

d1

Supply (Outlet) Temperature (F or C)

 

 

d2

Return (Inlet) Temperature (F or C)

 

 

d3

Fan Speed (rpm ÷ 10) [ex. 200 = 2000 rpm]

 

 

d4

Flame Signal (µA)

 

 

d5

Boiler Circulator Status (0 = Off, 1 = On)

 

 

d6

Boiler Set Point (F or C)

 

 

d7

Power On Time (Hrs ÷ 1000) [ex. 0.1 = 100 hrs]

 

 

d8

Boiler On Time (Hrs ÷ 1000)

 

 

d9

Boiler Cycles (n ÷ 1000)

 

 

7.Service Mode: The Pinnacle boiler can be operated in Service Mode to allow the installer to manually set the fan speed/input rate of the boiler.

a.To enter service mode, press and hold the S2/+ key and the S3 "Program" key simultaneously.

b.The display will alternately display "SER" and the fan speed in RPMs ÷ 10. As default, the fan speed will start at the ignition fan speed (this value is listed in Section 10, Dimensions and Ratings, for each boiler size).

c.The fan speed can be adjusted by using the S1/- key (to decrease speed) or S2/+ key (to increase speed) on the display module.

d.The fan speed will stay in this mode for 10 minutes or until the boiler reaches 7 degrees above the set point temperature.

e.To exit the Service Mode, press the S1/- or S2/+ keys simultaneously.

8.Installer Menu: The Pinnacle boiler can be programmed to be controlled by an external analog input controlling set point temperature or fan speed. In addition, it can be programmed for a 6 minute step modulation sequence.

a.To enter the installer menu, press and hold the S3 "Program" key and S4 "Reset" key simultaneously for 3 seconds. The display will show a blinking "000."

Table 6.4: Installer Menu

Parameter

 

Function

No.

 

 

 

 

 

 

1

0

= Internal Control

1

= External Input from 0-10 volt adapter

 

 

 

 

2

0

= External Temperature Input

1

= External Fan Speed Input

 

 

 

 

3

0

= Step Modulation Disabled

1

= Step Modulation Enabled

 

 

 

 

b.Use the S1/- and S2/+ keys to change the display to read 125. Press the S3 "Program" key to enter the installer menu. (The control will shut down the boiler if it is in operation.) The display will alternate between 1 and a value of either 0 or 1.

c.Table 6.4 shows the Parameter numbers and Functions. Press S3 "Program" to advance through the parameters and use the S1/- and S2/+keys to change the function values. Do not change to external input without external input device installed!

d.To exit the Installer Menu, press and hold the S4 “Reset” key for 3 seconds.

Figure 6.4: Display Module

29

Image 31
Contents Peerless Pinnacle Table of Contents Installation Sequence Using this ManualSpecial Attention Boxes Combustion and Ventilation AIR PreinstallationGeneral Accessibility Clearances Codes & RegulationsAccessibility Clearances Floor Standing Units Floor Mounted Boilers Boiler SET-UPGeneral Wall Hung BoilersOperating Parameters Water Piping and ControlsSystem Components Boiler Inputs and Outputs Net I=B=R Output Model Btu/hr kW Piping Symbol KeyGrundfos Circulator Flow Rate and Pressure Drop Boiler ModelFeet meters Recommended Circulators BoilerPinnacle Circulator Sizing Graph System Piping Freeze ProtectionOne Boiler, Primary/Secondary with Two Zones Zone Circulator Water Piping and Controls Water Piping and Controls Water Piping and Controls Three Boilers, Primary/Secondary with Four Zones Zone Valves Special Applications Boiler in conjunction with a Chilled Water System Feet Pipe GAS Supply Piping InstallationGAS Piping Fuel Line SizingGas Supply Piping Sediment Trap GAS Supply Piping OperationMain GAS Valve Operation Recommended Vent CO² Settings Firing Gas Type RateExhaust Vent / AIR Intake Pipe Location Approved Materials for Exhaust Vent and Intake AIR PipeFitting Equivalent Length Table Fitting Description Exhaust Vent and Intake AIR Pipe SizingVent Termination Kits Stock Description Code Exhaust Vent and AIR Intake Pipe InstallationVENTING, Inlet AIR and Condensate PI-T50 & PI-T80 Sidewall Venting with 2 Pipe 2 Vent Kit With 2 Pipe With 2 Pipe Concentric Vent Kit Venting with 3 Pipe Venting with 3 Pipe Concentric Vent KitExhaust Tapping for Vent Sample Condensate Drain InstallationBoiler Removal from Common Venting System Electrical WiringSequence of Operation Boiler Control Board Wiring Schematic Control Functions Safety InterlocksStatus Menu Description Code Installer Menu Parameter FunctionCompleting the Installation START-UP ProceduresLighting and Operating Procedures For Your Safety Read Before OperatingCHECK-OUT Procedure Boiler Error TroubleshootingBoiler Fault Fault Code Description Corrective Action P125 Control Board Fault CodesAnnually Before Start of Heating Season MaintenanceGeneral with Boiler in USE Weekly with Boiler in USEGAS Leaks Reset thermostats Important Make Boiler Dimensions Boiler Dimensions & RatingsPI-80/PI-140/PI-199 Dimensions Sch 40 PVC LbsRepair Parts Repair Parts Advantages of the P125 Control Board Appendix A. WHAT’S NEW with the P125 Control BoardP125 Control Board Quick Reference Figure A.2Comparative Control Board Sequence of Operation P125 Control Board VS. WHA Control Board ComparisonPeerless Pinnacle

Gas Boiler specifications

PB Heat Gas Boilers are renowned for their efficiency, reliability, and advanced technology, making them a popular choice for residential heating needs. With a range of models available, these boilers cater to various heating requirements while maintaining high performance and energy efficiency.

One of the standout features of PB Heat Gas Boilers is their exceptional efficiency ratings. Most models are designed to achieve AFUE (Annual Fuel Utilization Efficiency) ratings of over 90%, ensuring minimal energy waste and lower utility bills for homeowners. This high efficiency not only translates to cost savings but also contributes to a reduced carbon footprint, making PB Heat boilers a sustainable choice for environmentally conscious consumers.

PB Heat utilizes cutting-edge technologies to enhance the performance of their gas boilers. One such technology is the dual-stage gas valve, which allows for better modulation of gas flow, enabling the boiler to adapt to varying heating demands. This feature ensures consistent comfort while minimizing unnecessary energy consumption. Additionally, many PB Heat models come equipped with smart controls that can be easily integrated with home automation systems, giving homeowners the ability to monitor and adjust their heating remotely for maximum convenience and efficiency.

Durability and ease of maintenance are also key characteristics of PB Heat Gas Boilers. Constructed from high-quality materials, these boilers are designed to withstand the rigors of day-to-day operation. Features such as a corrosion-resistant heat exchanger contribute to the longevity of the unit, while easily accessible components simplify routine maintenance tasks, reducing downtime and service costs.

PB Heat Gas Boilers are available in various configurations, including wall-mounted and floor-standing models, catering to different space and installation requirements. This versatility allows homeowners to choose a solution that best fits their living environment while ensuring optimal heating performance.

In conclusion, PB Heat Gas Boilers represent a blend of advanced technology, energy efficiency, and robust construction. With their high efficiency ratings, smart control options, and durable design, these boilers provide reliable heating solutions for homes of all sizes. Choosing a PB Heat Gas Boiler means investing in a product that not only delivers comfort but also aligns with energy-saving and sustainability goals.