PB Heat Gas Boiler Piping Symbol Key, Boiler Inputs and Outputs Net I=B=R Output Model Btu/hr kW

Page 8

WATER PIPING AND CONTROLS

Figure 3.1: Piping Symbol Key

9.Pressure Relief Valve: The boiler pressure relief valve is factory installed into the right side boiler manifold (inside the jacket). Pipe the discharge of the relief valve to within 12" of the floor and close to a floor drain. Provide piping that is the same size or larger than the relief valve outlet.

CAUTION

Pipe the discharge of the relief valve as close as possible to the floor and away from high traffic areas. Pipe the discharge to a floor drain. Failure to do so may result in personal injury and/or property damage.

10.Circulator: The boiler circulator is to be sized to overcome the pressure drop of the system while providing the flow required by the boiler.

a.If the boiler is piped in a secondary loop of a primary/secondary heating system, the circulator will need only to overcome the resistance of the boiler and any fittings in that loop.

b.The circulator should be sized based on the net output of the boiler. The Table 3.2 shows the Boiler Output as reported to the Hydronics Institute division of GAMA. These values are based on a pickup factor of 1.15.

Table 3.2 – Boiler Inputs and Outputs

Boiler

Boiler Input

Net I=B=R Output

Model

(Btu/hr [kW])

(Btu/hr [kW])

 

 

 

PI-T50

50,000 (14.7)

40,000 (11.7)

 

 

 

PI-T80

80,000 (23.4)

64,000 (18.8)

 

 

 

PI-80

80,000 (23.4)

64,000 (18.8)

 

 

 

PI-140

140,000 (41.0)

112,000 (32.8)

 

 

 

PI-199

199,000 (58.3)

159,000 (46.6)

 

 

 

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Peerless Pinnacle Table of Contents Special Attention Boxes Using this ManualInstallation Sequence Preinstallation General Accessibility ClearancesCodes & Regulations Combustion and Ventilation AIRAccessibility Clearances Floor Standing Units Boiler SET-UP GeneralWall Hung Boilers Floor Mounted BoilersSystem Components Water Piping and ControlsOperating Parameters Piping Symbol Key Boiler Inputs and Outputs Net I=B=R Output Model Btu/hr kWFlow Rate and Pressure Drop Boiler Model Feet metersRecommended Circulators Boiler Grundfos CirculatorSystem Piping Freeze Protection Pinnacle Circulator Sizing GraphOne Boiler, Primary/Secondary with Two Zones Zone Circulator Water Piping and Controls Water Piping and Controls Water Piping and Controls Three Boilers, Primary/Secondary with Four Zones Zone Valves Special Applications Boiler in conjunction with a Chilled Water System GAS Supply Piping Installation GAS PipingFuel Line Sizing Feet PipeGAS Supply Piping Operation Gas Supply Piping Sediment TrapRecommended Vent CO² Settings Firing Gas Type Rate Main GAS Valve OperationApproved Materials for Exhaust Vent and Intake AIR Pipe Exhaust Vent / AIR Intake Pipe LocationExhaust Vent and Intake AIR Pipe Sizing Fitting Equivalent Length Table Fitting DescriptionExhaust Vent and AIR Intake Pipe Installation Vent Termination Kits Stock Description CodeVENTING, Inlet AIR and Condensate PI-T50 & PI-T80 Sidewall Venting with 2 Pipe 2 Vent Kit Venting with 3 Pipe Venting with 3 Pipe Concentric Vent Kit With 2 Pipe With 2 Pipe Concentric Vent KitBoiler Removal from Common Venting System Condensate Drain InstallationExhaust Tapping for Vent Sample Sequence of Operation WiringElectrical Boiler Control Board Wiring Schematic Safety Interlocks Control FunctionsInstaller Menu Parameter Function Status Menu Description CodeSTART-UP Procedures Completing the InstallationFor Your Safety Read Before Operating Lighting and Operating ProceduresCHECK-OUT Procedure Boiler Fault TroubleshootingBoiler Error P125 Control Board Fault Codes Fault Code Description Corrective ActionMaintenance General with Boiler in USEWeekly with Boiler in USE Annually Before Start of Heating SeasonGAS Leaks Reset thermostats Important Make Boiler Dimensions & Ratings Boiler DimensionsPI-80/PI-140/PI-199 Dimensions Lbs Sch 40 PVCRepair Parts Repair Parts P125 Control Board Quick Reference Appendix A. WHAT’S NEW with the P125 Control BoardAdvantages of the P125 Control Board P125 Control Board VS. WHA Control Board Comparison Figure A.2Comparative Control Board Sequence of OperationPeerless Pinnacle

Gas Boiler specifications

PB Heat Gas Boilers are renowned for their efficiency, reliability, and advanced technology, making them a popular choice for residential heating needs. With a range of models available, these boilers cater to various heating requirements while maintaining high performance and energy efficiency.

One of the standout features of PB Heat Gas Boilers is their exceptional efficiency ratings. Most models are designed to achieve AFUE (Annual Fuel Utilization Efficiency) ratings of over 90%, ensuring minimal energy waste and lower utility bills for homeowners. This high efficiency not only translates to cost savings but also contributes to a reduced carbon footprint, making PB Heat boilers a sustainable choice for environmentally conscious consumers.

PB Heat utilizes cutting-edge technologies to enhance the performance of their gas boilers. One such technology is the dual-stage gas valve, which allows for better modulation of gas flow, enabling the boiler to adapt to varying heating demands. This feature ensures consistent comfort while minimizing unnecessary energy consumption. Additionally, many PB Heat models come equipped with smart controls that can be easily integrated with home automation systems, giving homeowners the ability to monitor and adjust their heating remotely for maximum convenience and efficiency.

Durability and ease of maintenance are also key characteristics of PB Heat Gas Boilers. Constructed from high-quality materials, these boilers are designed to withstand the rigors of day-to-day operation. Features such as a corrosion-resistant heat exchanger contribute to the longevity of the unit, while easily accessible components simplify routine maintenance tasks, reducing downtime and service costs.

PB Heat Gas Boilers are available in various configurations, including wall-mounted and floor-standing models, catering to different space and installation requirements. This versatility allows homeowners to choose a solution that best fits their living environment while ensuring optimal heating performance.

In conclusion, PB Heat Gas Boilers represent a blend of advanced technology, energy efficiency, and robust construction. With their high efficiency ratings, smart control options, and durable design, these boilers provide reliable heating solutions for homes of all sizes. Choosing a PB Heat Gas Boiler means investing in a product that not only delivers comfort but also aligns with energy-saving and sustainability goals.
Top Page Image Contents