Orbit Manufacturing ORBIT-6 RP-206 manual System Time Locations

Page 16
Sounder
Cutoff
Entry Delay
Exit Delay
Master Code
Installer Code

Location: 09

Installer Code II

Default: 1206

Same as the Installer Code 1, but with a few limitations: It can't modify the "default code", observe and modify the first installer's codes, modify any MS phone number, nor observe & modify MS lock code.

Location: 10

Master Code

Default: 1234

PURPOSE: to establish the keypad code for the system’s “chief user”; the Master Code provides the following special privileges:

to enter, modify, and delete the remaining nine User Codes

to set the system's internal clock

to perform certain system functions and tests

Note: the Master Code cannot be seen by the installer through the zone LEDs on the keypad.

SYSTEM TIME: LOCATIONS 11-13

Location: 11 Exit Delay

Default: 030

PURPOSE: to establish the system’s Exit Delay (the interval, in seconds, between entering a User Code at the keypad and when the system actually arms).

Enter three digits between 001 and 255 seconds

Location: 12

Entry Delay

Default: 060

PURPOSE: to establish the system’s Entry Delay (in an armed system, the interval, in seconds, between the moment an entry door is opened and an alarm is triggered). Enter three digits between 001 and 255 seconds

Location: 13 Bell Cutoff Time

Default: 04

PURPOSE: to set the interval that the system’s external sounder(s) will operate before it shuts off automatically.

Enter the number of minutes between 01 and 90

INTRUSION ZONE TYPES AND ZONE SOUNDS: LOCATIONS 14-21

Locations 14 through 21 are identical and are corresponding to Zones 1 through 6 or 8 (in the 8-zone keypad), respectively. Each of these locations contains two digits.

the first digit: Contains the number used to represent the Type of Zone desired

the second digit: Contains the number used to represent the sound produced

when in alarm

Note: 1. When using 6 zone keypad the system disregards zones 7 - 8.

2.When using 8 zone keypad, zones 7 - 8 must be connected to an EOL resister when not in use.

16

Installer Manual

Image 16
Contents Installer Manual VER. B For service centers please see back cover Customer Information5IN206IM B Silencing an Alarm Reset Smoke DetectorsDisplay Troubles Display Memory Setting/Changing Maintenance On/Off BuzzerTable of Contents Main Features Introduction to the ORBIT-6Installation Before You BeginTechnical Data Main PanelRestoring Factory Defaults to the ORBIT-6 Installer ProgrammingKeypad Introduction to ProgrammingProgramming your Orbit-6 Orbit ProgrammerViewing the Contents of a Location Hexadecimal DigitsLocations Whose Contents Occupy More Than One Digit Audible Tones and Error BeepsHow to program installer parameters Programming TutorialInstaller Mode Access Press 0, 8, ARMCurrent Installer Code Installer CodeGeneral System Parameters Locations Location Default Enable DefLocation 01 MS Lock Def System Codes Locations System Time Locations Intrusion Zone Types and Zone Sounds LocationsInterior + Entry Delay Follower Key-switch Zone InstantKey-switch Zone Delayed Fire ZoneSpecial Zone Types Utility Outputs Locations Location 19 Zone 6 Tamper ZoneAlarm Follow Latched Alarm Follow PulseZone 1 Alarm Follow Latched Zone 1 Alarm Follow PulsedAUX Power Switch Fire Low Battery Follow LatchedLow Battery Follow Pulse Voice Module EnableDigital Communicator Controls Location Communication Parameters LocationsLocation Dialer Controls 2nd Digit Attempts Central Station Protocols LocationFormat Name Location CS Protocols 1 st Digit St Digit Format Understanding the Code FormatLocation CS Protocols 2 nd Digit Nd Digit Data Rate System Controls Location Upload/Download Rings LocationComments on System Controls Location 30 1st Digit Silent Panic Bell Squawk on Arming Minute Bypass Enabled Comments on System Controls Location 30 2nd DigitLocation System Controls 1st Digit St Digit Location System Controls 2 nd Digit Nd DigitReporting Codes for Alarm Events Location Periodic Test Time DefaultPeriodic Test Time Location Communicator Reporting Codes Locations 32 ThroughOther Reporting Codes Trouble Reports and RestoralsORBIT-6 Installer Programming Worksheet Location Description EntryZones Alarms/Disarm Zones Alarms/Disarm Program Digit CodeEvent Reporting Contact ID Code Program DigitSpecial AccessTroubles ORBIT-6 Wiring Diagram ORBIT-6 Wiring Diagram Zone Keypad Board Installer Manual Installer Manual Rokonet Limited Warranty

ORBIT-6 RP-206 specifications

Orbit Manufacturing's ORBIT-6 RP-206 is a state-of-the-art device designed to meet the evolving demands of modern manufacturing processes. Known for its reliability and versatility, the ORBIT-6 RP-206 integrates advanced technologies that enhance operational efficiency and productivity across various industrial applications.

One of the main features of the ORBIT-6 RP-206 is its robust construction, which ensures durability even in the most demanding environments. Built from high-grade materials, this equipment is designed to withstand wear and tear, thus reducing maintenance costs and downtime. The incorporation of a high-performance motor allows for improved power efficiency and faster processing speeds, enabling manufacturers to increase their output without sacrificing quality.

The ORBIT-6 RP-206 utilizes cutting-edge automation technologies. Equipped with a user-friendly interface, it allows for seamless integration into existing manufacturing systems. This system includes programmable features that enable users to customize operations according to their specific requirements. This flexibility makes it an ideal choice for small to medium-sized businesses as well as large-scale manufacturing facilities.

Moreover, one of the standout characteristics of the ORBIT-6 RP-206 is its advanced data analytics capabilities. By leveraging real-time data, manufacturers can continuously monitor performance metrics, allowing for proactive decision-making and process optimization. This feature not only enhances productivity but also contributes to quality control by identifying any deviations or anomalies during production.

Safety is another paramount concern for Orbit Manufacturing. The ORBIT-6 RP-206 incorporates various safety mechanisms, including automatic shut-off systems and emergency stops, ensuring a secure working environment for operators. Additionally, the machine is designed with easy access to key components for maintenance, further reinforcing its commitment to user safety and convenience.

In terms of environmental considerations, the ORBIT-6 RP-206 is engineered to minimize energy consumption and reduce waste. This eco-friendly approach resonates with the growing trend towards sustainable manufacturing practices, ensuring that businesses can meet their environmental goals while maintaining operational efficiency.

In conclusion, Orbit Manufacturing's ORBIT-6 RP-206 stands out as a technologically advanced solution for the modern manufacturing landscape. With its robust construction, automation capabilities, data analytics, safety features, and environmental consciousness, it is poised to deliver exceptional performance, making it an invaluable asset for any manufacturing operation.