Orbit Manufacturing ORBIT-6 RP-206 manual Before You Begin, Installation

Page 7

INSTALLATION

Before You Begin

Be sure the actual work is performed by experienced personnel, licensed to carry out security system installations and capable of implementing all applicable requirements of the National Fire Protection Association (NFPA-70 and NFPA-74), as well as any federal, state, and local codes–along with any safety guidelines and regulations which might apply.

Mounting and Wiring the Control Panel (refer to figures 1A, 1B & 1C on pages

32, 33 & 34)

1.Mount the ORBIT-6’s metal cabinet at a protected dry location, near a source of unswitched AC Power, a good ground, and access to telephone service. Use the proper hardware (e.g. anchors, mollys, toggle bolts, etc.), as required, to insure a suitable mounting.

2.Thread all electrical wiring through a convenient hole in the metal cabinet. To prevent potential damage, be sure that live AC power is NOT present and that the Standby Battery is NOT connected. Refer to Figures 1A and 1B. Your wiring may include any and all of the following:

∙connections to Hardwired Zones

∙connections to devices requiring Uninterrupted Auxiliary Power (e.g. PIRs, Glass Break Detectors)

∙connections to Smoke Detectors requiring Resettable Power

∙connections to any External Sounders

3.If using Utility Output, connect the UO/ECL output, this terminal is designed to activate a low current device (e.g. a 12 VDC Relay, drawing no more than 70 mA).

If using UO expansion module, connect the UO/ECL terminal to the ECL terminal input in the expansion module. In this case the first UO on the expansion module will become UO1. (see figures A1)

4.Make connections from the RJ31X (or equivalent) telephone company interface.

5.Make connections to the system’s keypad(s) by the correspnding wire colors.

6.Make connections to AC Power (via a 16.5 VAC, 25 VA transformer). Do not plug in the transformer at this time.

7.Have a Standby Battery ready (typically 12 VDC, 4 AH), but do not connect it at this time.

8.All zone inputs are End Of Line supervised, use 2200 ohm resistors (supplied).

9.When using 8 LED keypad, zones 7 & 8 are end-of-line supervised. Use 2200 ohm resisters (supplied) when the zones are not in use. For further wiring instructions of the 8 LED keypad, refer to Figure 1C on page 34.

10.If using a Key-switch, use a momentary key-switch. The receiver (if used) must give a pulse output and not on/off.

11.To connect the panic button use the white wire as (+) and the black wire as (-).

Note: The maximum distance between the panic button and the keypad is 30 meters.

Installer Manual

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Installer Manual VER. B Customer Information For service centers please see back cover5IN206IM B Maintenance On/Off Buzzer Silencing an AlarmReset Smoke Detectors Display Troubles Display Memory Setting/ChangingTable of Contents Introduction to the ORBIT-6 Main FeaturesBefore You Begin InstallationMain Panel Technical DataIntroduction to Programming Restoring Factory Defaults to the ORBIT-6Installer Programming KeypadOrbit Programmer Programming your Orbit-6Hexadecimal Digits Viewing the Contents of a LocationProgramming Tutorial Locations Whose Contents Occupy More Than One DigitAudible Tones and Error Beeps How to program installer parametersInstaller Code InstallerMode Access Press 0, 8, ARM Current Installer CodeGeneral System Parameters Locations Location Default Enable DefLocation 01 MS Lock Def System Codes Locations Intrusion Zone Types and Zone Sounds Locations System Time LocationsFire Zone Interior + Entry Delay FollowerKey-switch Zone Instant Key-switch Zone DelayedSpecial Zone Types Location 19 Zone 6 Tamper Zone Utility Outputs LocationsZone 1 Alarm Follow Pulsed Alarm Follow LatchedAlarm Follow Pulse Zone 1 Alarm Follow LatchedVoice Module Enable AUX Power Switch FireLow Battery Follow Latched Low Battery Follow PulseCommunication Parameters Locations Digital Communicator Controls LocationLocation Dialer Controls 2nd Digit Attempts Central Station Protocols LocationFormat Name Location CS Protocols 1 st Digit St Digit Format Understanding the Code FormatLocation CS Protocols 2 nd Digit Nd Digit Data Rate System Controls Location Upload/Download Rings LocationComments on System Controls Location 30 1st Digit Location System Controls 2 nd Digit Nd Digit Silent Panic Bell Squawk on Arming Minute Bypass EnabledComments on System Controls Location 30 2nd Digit Location System Controls 1st Digit St DigitCommunicator Reporting Codes Locations 32 Through Reporting Codes for Alarm EventsLocation Periodic Test Time Default Periodic Test Time LocationTrouble Reports and Restorals Other Reporting CodesLocation Description Entry ORBIT-6 Installer Programming WorksheetCode Program Digit Zones Alarms/DisarmZones Alarms/Disarm Program Digit Code Event Reporting Contact IDSpecial AccessTroubles ORBIT-6 Wiring Diagram ORBIT-6 Wiring Diagram Zone Keypad Board Installer Manual Installer Manual Rokonet Limited Warranty

ORBIT-6 RP-206 specifications

Orbit Manufacturing's ORBIT-6 RP-206 is a state-of-the-art device designed to meet the evolving demands of modern manufacturing processes. Known for its reliability and versatility, the ORBIT-6 RP-206 integrates advanced technologies that enhance operational efficiency and productivity across various industrial applications.

One of the main features of the ORBIT-6 RP-206 is its robust construction, which ensures durability even in the most demanding environments. Built from high-grade materials, this equipment is designed to withstand wear and tear, thus reducing maintenance costs and downtime. The incorporation of a high-performance motor allows for improved power efficiency and faster processing speeds, enabling manufacturers to increase their output without sacrificing quality.

The ORBIT-6 RP-206 utilizes cutting-edge automation technologies. Equipped with a user-friendly interface, it allows for seamless integration into existing manufacturing systems. This system includes programmable features that enable users to customize operations according to their specific requirements. This flexibility makes it an ideal choice for small to medium-sized businesses as well as large-scale manufacturing facilities.

Moreover, one of the standout characteristics of the ORBIT-6 RP-206 is its advanced data analytics capabilities. By leveraging real-time data, manufacturers can continuously monitor performance metrics, allowing for proactive decision-making and process optimization. This feature not only enhances productivity but also contributes to quality control by identifying any deviations or anomalies during production.

Safety is another paramount concern for Orbit Manufacturing. The ORBIT-6 RP-206 incorporates various safety mechanisms, including automatic shut-off systems and emergency stops, ensuring a secure working environment for operators. Additionally, the machine is designed with easy access to key components for maintenance, further reinforcing its commitment to user safety and convenience.

In terms of environmental considerations, the ORBIT-6 RP-206 is engineered to minimize energy consumption and reduce waste. This eco-friendly approach resonates with the growing trend towards sustainable manufacturing practices, ensuring that businesses can meet their environmental goals while maintaining operational efficiency.

In conclusion, Orbit Manufacturing's ORBIT-6 RP-206 stands out as a technologically advanced solution for the modern manufacturing landscape. With its robust construction, automation capabilities, data analytics, safety features, and environmental consciousness, it is poised to deliver exceptional performance, making it an invaluable asset for any manufacturing operation.
Top Page Image Contents