Orbit Manufacturing ORBIT-6 RP-206 Utility Outputs Locations, Location 19 Zone 6 Tamper Zone

Page 19

Location: 18 Zone 5: (2nd Digit): Sound

Default: External Sounder (Pulses)

For fire zone the recommended (default) zone sound is “External sounder pulsed” However it is possible to change the zone sound and type to any of the ones provided in the previous list.

Location: 19 Zone 6: Tamper Zone

Zone 6 is reserved as a Tamper Zone. This zone can be programmed to any zone type (except Fire) including Tamper. If the zone was programmed as Tamper, in violation, a Tamper Code report will be sent and the Tamper LED on the keypad (marked as 6/Tmp) will light up.

UTILITY OUTPUTS: LOCATIONS 22-25

The ORBIT-6 supports one open collector Utility Output (derived between the UO/ECL and AUX terminals) which can be used for switching an external device on or off. Once the Utility Output is activated the device will be connected between AUX (+12V) and ground (0V). This connection is capable of switching light loads of no more than 70mA.

Note: When activated the utility output is switched to the Negative Polarity.

The “UO” can be also used to reset a “latched” Smoke Detector(s). In that case the 12V power to the smoke detector will be supplied via the UO (see Figures 1A and 1B). The UO should be defined as AUX switch.

If the Utility Output Expansion Module is being used, the same information in Location 22 is applicable for the programming of UO2 (Location 23), UO3 (Location 24), and/or UO4 (Location 25). It is not necessary to program all of the available “UOs”, unless they’re used. Note that when the Utility Output Expansion Module is employed, the original Utility Output on the Main Board (the UO/ECL terminal) is no longer available.

Important: In order to use the Utility Output Expansion you have to define the module in Location 30.

22

If more than one “UO” output is necessary, a Utility Output Expansion Module is available. Its four “UOs” (U01, UO2, UO3, and UO4) replace the ORBIT-6’s single “on-board ”UO”. The “UOs” on the Utility Output Expansion Module are relay-based, and allow a maximum current of 500 mAs. Refer to Figures 1A and 1B (pages 32 and 33), for wiring instructions and additional information. The figure at the right, shows how a Utility Output on the “UO Expander” can be used to switch a table lamp on and off.

Because of the “UO’s” modest 70 mA current capability, it will be necessary to use an “intermediate” relay-whose physical contacts can switch far greater currents (limited by their contact rating). The figure at the left shows how such a relay can trigger a strobe light. If used in this manner, the “UO”cannot be used to reset a “latched” Smoke Detector(s).

23)

16.

Installer Manual

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Installer Manual VER. B Customer Information For service centers please see back cover5IN206IM B Maintenance On/Off Buzzer Silencing an AlarmReset Smoke Detectors Display Troubles Display Memory Setting/ChangingTable of Contents Introduction to the ORBIT-6 Main FeaturesBefore You Begin InstallationMain Panel Technical DataIntroduction to Programming Restoring Factory Defaults to the ORBIT-6Installer Programming KeypadOrbit Programmer Programming your Orbit-6Hexadecimal Digits Viewing the Contents of a LocationProgramming Tutorial Locations Whose Contents Occupy More Than One DigitAudible Tones and Error Beeps How to program installer parametersInstaller Code InstallerMode Access Press 0, 8, ARM Current Installer CodeGeneral System Parameters Locations Location Default Enable DefLocation 01 MS Lock Def System Codes Locations Intrusion Zone Types and Zone Sounds Locations System Time LocationsFire Zone Interior + Entry Delay FollowerKey-switch Zone Instant Key-switch Zone DelayedSpecial Zone Types Location 19 Zone 6 Tamper Zone Utility Outputs LocationsZone 1 Alarm Follow Pulsed Alarm Follow LatchedAlarm Follow Pulse Zone 1 Alarm Follow LatchedVoice Module Enable AUX Power Switch FireLow Battery Follow Latched Low Battery Follow PulseCommunication Parameters Locations Digital Communicator Controls LocationLocation Dialer Controls 2nd Digit Attempts Central Station Protocols LocationFormat Name Location CS Protocols 1 st Digit St Digit Format Understanding the Code FormatLocation CS Protocols 2 nd Digit Nd Digit Data Rate System Controls Location Upload/Download Rings LocationComments on System Controls Location 30 1st Digit Location System Controls 2 nd Digit Nd Digit Silent Panic Bell Squawk on Arming Minute Bypass EnabledComments on System Controls Location 30 2nd Digit Location System Controls 1st Digit St DigitCommunicator Reporting Codes Locations 32 Through Reporting Codes for Alarm EventsLocation Periodic Test Time Default Periodic Test Time LocationTrouble Reports and Restorals Other Reporting CodesLocation Description Entry ORBIT-6 Installer Programming WorksheetCode Program Digit Zones Alarms/DisarmZones Alarms/Disarm Program Digit Code Event Reporting Contact IDSpecial AccessTroubles ORBIT-6 Wiring Diagram ORBIT-6 Wiring Diagram Zone Keypad Board Installer Manual Installer Manual Rokonet Limited Warranty

ORBIT-6 RP-206 specifications

Orbit Manufacturing's ORBIT-6 RP-206 is a state-of-the-art device designed to meet the evolving demands of modern manufacturing processes. Known for its reliability and versatility, the ORBIT-6 RP-206 integrates advanced technologies that enhance operational efficiency and productivity across various industrial applications.

One of the main features of the ORBIT-6 RP-206 is its robust construction, which ensures durability even in the most demanding environments. Built from high-grade materials, this equipment is designed to withstand wear and tear, thus reducing maintenance costs and downtime. The incorporation of a high-performance motor allows for improved power efficiency and faster processing speeds, enabling manufacturers to increase their output without sacrificing quality.

The ORBIT-6 RP-206 utilizes cutting-edge automation technologies. Equipped with a user-friendly interface, it allows for seamless integration into existing manufacturing systems. This system includes programmable features that enable users to customize operations according to their specific requirements. This flexibility makes it an ideal choice for small to medium-sized businesses as well as large-scale manufacturing facilities.

Moreover, one of the standout characteristics of the ORBIT-6 RP-206 is its advanced data analytics capabilities. By leveraging real-time data, manufacturers can continuously monitor performance metrics, allowing for proactive decision-making and process optimization. This feature not only enhances productivity but also contributes to quality control by identifying any deviations or anomalies during production.

Safety is another paramount concern for Orbit Manufacturing. The ORBIT-6 RP-206 incorporates various safety mechanisms, including automatic shut-off systems and emergency stops, ensuring a secure working environment for operators. Additionally, the machine is designed with easy access to key components for maintenance, further reinforcing its commitment to user safety and convenience.

In terms of environmental considerations, the ORBIT-6 RP-206 is engineered to minimize energy consumption and reduce waste. This eco-friendly approach resonates with the growing trend towards sustainable manufacturing practices, ensuring that businesses can meet their environmental goals while maintaining operational efficiency.

In conclusion, Orbit Manufacturing's ORBIT-6 RP-206 stands out as a technologically advanced solution for the modern manufacturing landscape. With its robust construction, automation capabilities, data analytics, safety features, and environmental consciousness, it is poised to deliver exceptional performance, making it an invaluable asset for any manufacturing operation.
Top Page Image Contents