Nilfisk-ALTO SR1800C B-D manuel dutilisation Safety Systems

Page 57

USER MANUAL

Engine

The engine, a Diesel Lombardini Focs 1204 (SR 1800C D) or motor Amre 48V (SR 1800C B) drives the hydraulic system pumps.

Front wheels

Pneumatic wheels

Superelastic wheels

They are independent, fastened to the frame by means of a hub with built-in brake drum. The brakes are hydraulic. The parking brake is mechanical.

Rear wheel

Pneumatic wheel

Superelastic wheel

The rear wheel is the driving and steering wheel. The steering is operated by a hydraulic cylinder connected to the power steering. A hydrostatic variable delivery pump with servoassisted control supplies a drive hydraulic motor for forward and reverse gear.

Dashboard

Fitted on the upper part of the frame and under the steering wheel, the dashboard houses the machine warning lights and instrumentation.

Hydraulic system

In the first circuit a variable delivery pump feeds the drive hydraulic motor (rear wheel). The forward and reverse drive are adjusted by a hydraulic assist operated by a pedal. In the second circuit a gear pump feeds the power steering and a distributor which controls: the hopper lifting cylinder, the side broom lifting and rotation cylinder, the skirt opening and closing cylinder; the power steering controls the steering cylinder.

In the third circuit the gear pump feeds a distributor which controls the main broom lifting/lowering and rotation cylinder and the fan hydraulic motor rotation.

All circuits are protected by suction filters and safety valves.

Electrical system

SR 1800C D: 12 V electrical system supplied by an alternator operated by the engine. The circuits are protected by lamellar fuses housed in a relevant fuse box.

SR 1800C B: power electrical system supplied by a 48 V battery. The accessory electrical system is supplied by a 12 V power supply. The circuits are protected by lamellar fuses housed in a relevant fuse box and by the power supply itself, that cuts the voltage supply in case of short circuit and then restarts it at circuit reset.

Stability

Machine stability depends on the conditions in which it is used.

If the machine is used within the conditions of use specified in the manual, it is stable. To this end the following tests were carried out under the same conditions on a prototype identical to the series model and no stability problems arose. The conditions were:

Flat ground with good surface conditions:

Transfer maximum speed: 14 km/h

Working speed: from 1 to 8 km/h

Bending radius (maximum speed of 14 km/h): 3 m

Bending radius (speed of 5 km/h): 0 m

On sloping ground with good surface conditions and maximum longitudinal slope of 20%:

Bending radius (maximum speed of 5 km/h): 3 m

Bending radius (speed of 1 km/h): 0 m Maximum crossfall while in transfer: 15% Maximum crossfall at 5 km/h: 20%

The tests were carried out with lowered and empty hopper. For different conditions of use, the machine operator should be able to assess the limits of the machine and should, in any case, follow the indications laid down in the manual.

Information on brooms

Side brooms (2, Fig. E)

Polypropylene side broom

Polypropylene and steel side broom

Steel side broom

Nylon side broom

Main brooms (12, Fig. E)

Natural fibre and polypropylene main broom

Polypropylene main broom

Polypropylene and steel main broom

Nylon main broom

Brooms with different bristles can be supplied on request.

SAFETY SYSTEMS

The machine is provided with an operator's seat sensor that stops the machine as soon as the operator leaves the seat.

33014817(2)2006-06 A

7

Image 57
Contents 3301481722006-06 a Modell/Modèle/Model/ModelEN 60335-1, EN 1616 Allgemeine Anweisungen BetriebsanleitungAllgemeine Anweisungen EinleitungVorbedingung MaschinenidentifizierungTerminologien UND Ihre Bedeutung Verantwortlichkeit DES BedienersSicherheitsvorschriften Warnzeichen TRANSPORT, VERLAGERUNG, InstallationAblanden UND Verlagern Siehe Abb. CTechnische Eigenschaften Maschinenbeschreibung Sicherheitssysteme Technische Daten SR 1800C DSR 1800C B Umgebungswerte AnwendungGeräuschpegel Steuerungen UND InstrumenteGebrauchsanweisungen Maschinenabstellen Gebrauch DER MaschineStörungen UND Abhilfen Störungen UND AbhilfenBetriebsanleitung Übermäßige Erwärmung des Motors SR 1800C B Reinigung Reinigung UND WartungPlanmässige Wartung Allgemeine Reinigung der MaschineAlle WartungstabelleWartung StundenGleichstrom-Fahrmotor SR 1800C B Ausserordentliche Wartung Betriebsbatterie Ladung ÜberladungWartung ABBAU, Entsorgung AbbauEntsorgung Pläne Position DER SicherungenSchaltpläne Siehe Abb. AJ Schaltplan SR 1800C BHydraulikanlage Zubehör UND SonderausstattungSaugschlauch Dritter SeitenbesenManuel Dutilisation Avertissements Generaux IntroductionPrecautions Pour LA Securite DES Operateurs Terminologie ET SignificationResponsabilite DE Loperateur Signaux Dattention TRANSPORT, MANUTENTION, InstallationDechargement ET Manutention Voir Fig. CEmballages Caracteristiques TechniquesControles Generaux Utilisation PrevueSR 1800C B Voir Fig. F Description DE LA MachineChâssis Conteneur déchetsSystemes DE Securite Données générales Donnees Techniques PrincipalesMoteur diesel ValeursUtilisation Commandes ET InstrumentsValeurs Environnementales Niveau DE BruitInstructions Pour Lutilisation Arret DE LA Machine Utilisation DE LA MachineProblemes ET Remedes Problemes ET RemedesContrôler la pression de la pompe à Réchauffement excessif du moteur SR 1800C B Nettoyage Nettoyage ET EntretienEntretien Periodique Nettoyage général de la machineToutes Tableau DentretienToutes Entretien LesMoteur à courant continu de traction SR 1800C B Entretien Extraordinaire Batterie DE Service Charge SurchargeEntretien DEMANTELEMENT, Ecoulement DemantelementEcoulement Schemas Schemas ElectriquesPosition Fusibles Voir fig. AJ Schéma électrique SR 1800C BSysteme Hydraulique Accessoires ET OptionsTuyau Daspiration Troisieme BrosseHydraulic System Foreword General WarningsMachine Identification Purpose Safe-KeepingDefinitions Operators Safety PrecautionsOperators Responsibility Exposed personTRANSPORTATION, HANDLING, Installation Discharge and HandlingSee Fig. C Packing Technical DataGeneral Checks USEMachine Description Safety Systems General data Main Technical DataDiesel engine ValuesEnvironmental Conditions USENoise Level Controls and InstrumentsInstructions for USE Machine Stop Machine USEProblems and Remedies Problems and Remedies3301481722006-06 a Motor overheating SR 1800C B Cleaning Cleaning and MaintenancePeriodical Maintenance Machine general cleaningMaintenance 000 Maintenance TableEvery HoursDrive direct current motor SR 1800C B Extraordinary Maintenance Accessory Battery Overcharge MaintenanceDISMANTLING, Disposal DismantlingDisposal Diagrams Wiring DiagramsFuse Positions See Fig. AJ Wiring diagram SR 1800C BHydraulic System Accessories and OptionsSuction Hose Third BroomAlgemene Waarschuwingen GebruikershandleidingAlgemene Waarschuwingen InleidingVoorwoord Identificatie VAN DE MachineVerantwoordelijkheid VAN DE Bediener DefinitiesVeiligheidsmaatregelen Voor DE Bediener GevarenzonesWaarschuwingstekens VERVOER, HANTERING, InstallatieLossen EN Bediening Zie Afb. CTechnische Gegevens Beschrijving VAN DE Machine Veiligheidssystemen Algemene gegevens Waarden Belangrijkste Technische GegevensDieselmotor Waarden Motor WaardenMilieu GebruikGeluidsniveau Bedieningen EN InstrumentenZonder koplampen Zie Afb. J GebruiksinstructiesSR 1800C B Met koplampen Zie Afb. K Zonder koplampen Zie Afb. LGebruik VAN DE Machine MachinestopAfvalverzameling Problemen EN Oplossingen Problemen EN OplossingenGebruikershandleiding Oververhitting motor SR 1800C B Reiniging Reiniging EN OnderhoudPeriodiek Onderhoud Algemene reiniging van de machineOnderhoudstabel OnderhoudNa 50 uur Aandrijving gelijkstroommotor SR 1800C B Buitengewoon Onderhoud Extra Accu Opladen OverladenOnderhoud DEMONTEREN, Afdanken DemonterenAfdanken SCHEMA’S BEDRADINGSSCHEMA’SZekeringenposities Zie Afb. AJ Bedradingsschema SR 1800C BHydraulisch Systeem Accessoires EN OptiesAanzuigslang Derde Borstel13e 13a 13b13i 13j 13k 13f3301481722006-06 a 3301481722006-06 a 3301481722006-06 a 16 159 86 3301481722006-06 a 3301481722006-06 a 3301481722006-06 a 3301481722006-06 a Page 530 520 111 104 345 560 480 570 520 830 376 15 16 770

SR1800C B-D specifications

The Nilfisk-ALTO SR1800C B-D is a powerful, efficient, and versatile ride-on scrubber drier designed for cleaning large areas in industrial, commercial, and retail environments. Combining advanced technology and user-friendly features, this machine streamlines the cleaning process while ensuring high-quality results.

One of the standout features of the SR1800C B-D is its impressive cleaning capacity. With a working width of 800 mm, it can cover expansive areas in a shorter amount of time. The dual scrubbing brush system enhances cleaning efficiency, allowing for thorough dirt and grime removal in various surfaces, including tile, concrete, and linoleum. The machine’s robust build quality ensures durability and longevity even in the most demanding environments.

Another notable aspect of the SR1800C B-D is its innovative Ecoflex system. This technology allows users to adjust the detergent dosage and water flow according to the specific cleaning task at hand. By using just the right amount of resources, the Ecoflex system promotes sustainable cleaning practices, reduces water usage, and minimizes environmental impact without compromising cleaning performance.

The machine is equipped with a highly efficient vacuum system that enhances drying performance. This feature not only helps to expedite the cleaning process but also reduces slip hazards, making it a safer option for both staff and customers in high-traffic areas. The adjustable suction power ensures that various floor types can be cleaned effectively.

User comfort is also a priority in the design of the SR1800C B-D. Its ergonomic controls and adjustable seat make it easy to operate for extended periods, reducing operator fatigue. The clear visual display provides essential information, such as battery level and service alerts, ensuring that users can maintain the machine effectively.

In terms of maintenance, the Nilfisk-ALTO SR1800C B-D is designed for easy access to components, simplifying routine tasks such as brush changes and tank cleaning. This thoughtful design significantly reduces downtime, allowing for consistent and uninterrupted cleaning operations.

In conclusion, the Nilfisk-ALTO SR1800C B-D offers an exceptional combination of efficiency, versatility, and user-friendly features. With its advanced cleaning technologies and focus on sustainability, this scrubber drier is an ideal choice for organizations looking to maintain cleanliness and safety in their facilities while optimizing operational costs.