Integra instruction manual Connections DTR-5.3, CD player CD

Connections (DTR-5.3)

Here is an explanation of typical ways to connect various components to the DTR-5.3. There are many ways that any one component can be connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be thought of as such. It is best to fully understand the nature of each connector and terminal as well as those of your components and their features to ascertain which method of connection is best.

: Signal flow

1. CD player (CD)

ANTENNA	FM 75		AM
				COMPONENT VI
				INPUT 2 INPUT 1
12 V				RS232
TRIGGER		IR OUT		LINE IN
OUT	56K		ZONE 2
		40K		DC IN
A			OUT	24V 1A
			A	L
			B
B				R

REMOTE
CONTROL	DIGITAL	DIGITAL	VIDEO 3	VIDEO 2	VIDEO 1		DVD
DIGITAL INPUT			IN	IN	OUT	IN	IN
	OUTPUT	INPUT

OPTICAL	OPTICAL COAXIAL	V
2	1

Digital audio output (optical)	CD
	IN
L (white)	L
	SUBWOOFER
	PRE OUT
	R
Analog audio output
R (red)

TAPE

OUT IN

S			2. Cassette tape deck, MD
			recorder, DAT deck, or CD
IN	IN	OUT IN FRONT	recorder (TAPE)
L		L
R		R	L (white)
VIDEO 3
	VIDEO 2	VIDEO 1
			Analog audio output

R(red)

L (white)

Analog audio input

R (red)

Connecting your audio components

Below is an example of how you can connect your audio components to the DTR-5.3. Refer to the diagram above for the following connection examples.

AUDIO IN/OUT

These are the analog audio inputs and outputs. There are six audio inputs and two audio outputs on the rear panel. The audio inputs and outputs require RCA-type connectors.

DIGITAL INPUT/OUTPUT

On the rear panel of the DTR-5.3, there are one coaxial digital input, two optical digital inputs, and one optical digital output. To the digital inputs, connect CD players, LD players, DVD players, or other digital source component. To the digital output, connect an MD recorder, CD recorder, DAT deck, or other similar component.

•Since an analog connection must be made when using REC OUT, make sure that the connection to the input source is not digital only, but analog as well.

•When using an optical input or output jack, always use an optical fiber cable.

1.Connecting a compact disc player (CD)

Using an RCA audio cable, connect the output jacks of the compact disc player to the CD audio jacks of the DTR-5.3. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the compact disc player has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the DTR-5.3 depending on the type of connector on the compact disc player.

With the initial settings of the DTR-5.3, the CD input source is set for digital input at the OPTICAL 1 jack (OPT 1).

If the digital connection is made to a different jack, this must be changed at “Input Setup” → “Digital Input” (see page 53).

2.Connecting a cassette tape deck, MD recorder, DAT deck, or CD recorder (TAPE)

Using RCA audio cables, connect the output jacks (PLAY) of the device to the TAPE IN audio jacks of the DTR-5.3 and connect the input jacks (REC) of the device to the TAPE OUT audio jacks of the DTR-5.3. Make sure that you properly connect the left channels to the L jacks and the right channels to the R jacks.

If the device has a digital output, connect it to either the DIGITAL INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of the DTR-5.3 depending on the type of connector on the device.

With the initial settings of the DTR-5.3, nothing is allocated as the digital input source for TAPE (----).

If you connect the digital audio output, be sure to make the appropriate changes at “Input Setup” → “Digital Input” (see page 53).

If the device has a digital input, connect it to the DIGITAL OUTPUT OPTICAL jack of the DTR-5.3 for digital recording of the signal from the digital input of the DTR-5.3.

Note:

The output from the DIGITAL OUTPUT jack of the DTR-5.3 is only the digital signal input to the DIGITAL INPUT jack.

23