Integra DTR-5.3 instruction manual Connecting antennas, Assembling the AM loop antenna

Page 35

Connecting antennas

To use the tuner of the DTR-6.3/5.3, it is necessary to prepare the supplied FM and AM antennas.

•Adjustment and placement of the FM and AM antennas for better reception must be done while listening to a station broadcast.

•If better reception cannot be obtained, then placement of an outside antenna is recommended.

Assembling the AM loop antenna

Assemble the loop antenna as shown in the illustration.

•Refer to “Connecting the AM loop antenna” below for details on how to connect the loop antenna.

Insert into the hole.

Connecting the AM antenna cable

1.Press down the lever at the antenna terminal.

2.Insert the wire into the terminal hole.

3.Release the lever.

1	2		3

Connecting the included antennas

Connecting the FM indoor antenna:

The FM indoor antenna is for indoor use only. During use, extend the antenna and adjust its orientation until the clearest signal is received. Fix it with push pins or similar items in the position that will cause the least amount of distortion.

If the reception is not very clear with the attached FM indoor antenna, the use of an outdoor antenna is recommended.

Connecting the AM loop antenna:

The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far away as possible from the DTR-6.3/5.3, televisions, speaker cables, and power cords.

If the reception is not very clear with the attached AM indoor antenna, the use of an outdoor antenna is recommended.

FM antenna

(Indoor)

AM loop antenna

ANTENNA	FM 75	AM			R	PHONO IN
ANTENNA					R		L
12 V							RS232
TRIGGER					ZONE 2
OUT	IR OUT		ZONE 2	DC IN	LINE OUT
	56K	40K	ZONE 2	DC IN
A		A	OUT	24V 1A		L
A		A

		B
B						R
	ZONE 2
DIGITAL INPUT		DIGITAL		VIDEO 3	VIDEO 2
		OUTPUT COAXIAL		IN	OUT	IN	OU
OPTICAL		OPTICAL
2	1
			COAXIAL
			DIGITAL
			INPUT
	IN	OUT	IN	IN	OUT	IN	OU

Strip away the insulation from the end of the cable, and fully insert the stripped end of the cable.

Hint:

Either of the split ends of the AM antenna can be connected to either terminal. Unlike speaker cabling, there is no polarity for AM broadcast signals.

35

Image 35

Contents DTR-6.3/5.3 Avis Important SafeguardsPrecautions Contents Contents DTR-6.3 Amplifier Features FeaturesUsing the remote controller Supplied accessoriesBefore using this unit Installing the remote controller batteriesDTR-6.3 DTR-5.3 Front panel facilitiesFront panel facilities Speakers A/B buttons DTR-5.3 only Sleep indicator Muting indicatorListening mode or digital input format indicators Tuning indicatorsRemote controller Remote controller Connections Connections Signal flow Connecting your audio componentsConnecting a compact disc player CD Connecting a turntable PhonoConnections DTR-6.3 Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Flow of the video signals is as followsConnecting a DVD player DVD Connecting a DVD Player with 2-Channel L/R Audio OutputVideo Connecting a video cassette recorder VideoMonitor OUT Connecting a television monitor or projector Monitor OUTFront left speaker Center speaker Connecting video camera, etc. Video 4 InputPower amplifier Front right speakerWhen using the Zone 2 OUT terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 PRE OUT terminals When using the Zone 2 Speakers terminalsCD player CD Connections DTR-5.3Video output Connections DTR-5.3Connections DTR-5.3 Video 2/3 Video output Digital output Optical DTR-6.3 only 12V Trigger OUT ZONE2 Power cord supplied To an AC wall outletConnections DTR-6.3/5.3 DTR-6.3/5.3 12V Trigger OUT A/BDirect change function Power on/ready functionPower off function Other component From connecting blockDTR-6.3 only Speaker placement Connecting speakersStandard speaker setup for surround sound Minimum speaker configuration for surround sound playbackConnecting to the Speakers B terminals DTR-5.3 only Connecting speakersConnecting speakers Connecting a subwooferRight Back Left Speaker Front Center Right Speaker LeftSubwoofer Surround Turning on the power Connecting the powerTurning on the power from the remote controller Assembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaDisplaying the Main Menu Configuring the speakersSpeaker Configuration Adjustable Crossover 80/100/120 Hz for Bass Management Configuring the speakersUse the and cursor buttons to select Left Calibrating the speaker levelsFeet Select if you will enter the distances in feet Meters Select if you will enter the distances in metersButtons used for navigating through the menus Using the remote controller Press the Test buttonPress the Test button to complete the procedure Listening to Radio Broadcasts Listening to a stereo radio station FM modeTuning into a radio station FM Mode Tuning TunerListening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationPress the desired input source Adjust the volume to an appropriate levelSelecting an Audio Component Basic operation DTR-6.3Speakers A/B Selecting an Audio ComponentBasic operation DTR-5.3 Selecting speakers Speakers A, B DTR-5.3 onlyTo change the display of the input source from Tape to MD Selecting the type of audio input signalTemporarily changing the speaker output levels Enjoying DVD multichannel audio playback Using the sleep time remote controller onlyListening with headphones Sleep Audio AdjustTemporarily turning off the sound Switching the displayListening Modes Listening Modes While playing back Dolby Digital 2-channel sources Selecting a listening modeRcvr Mode Listening mode buttons TipOriginal filter CinemaFILTER loading for movies Press the Cine Fltr button on the remote controllerInput Selector buttons Input SetupReturn Menu Input source buttons Return Setup Multichannel Input SetupDigital Input Digital FormatDigital Format Source IntelliVolumeAnalog/PCM Source PCM fs96kHz SourcePreference OSD Setup and Other SettingsOSD Setup To display the OSD Setup menuBass, Treble Audio AdjustSetup Procedure Press the Audio Adjust button Setting Values Initial valueAudio Adjust Late Settings possible for each listening modeAdjusting the volume using the remote controller Using the buttons on the DTR-6.3Adjusting the volume for the remote zone Ex. When the CD button is pressedStart recording at the recording component as desired Recording a source DTR-6.3Rec Out Off Input source buttons Recording a source DTR-5.3 Controlling an Onkyo cassette tape deck Using remote controllerCalling up a preset radio station Rcvr Mode VOL MutingControlling an Integra/Onkyo CD player Using remote controllerPress the CD Mode button Controlling an Integra/Onkyo DVD player Top Menu Audio SEL Angle Standby DVD Mode SetupPress the DVD Mode button To 9, 0, --/--- Numeric keys Press the MD Mode buttonControlling an Integra/Onkyo MD recorder Within 30 seconds, enter the 3-digit code number Entering a pre-programming codeLearning a pre-programming code Pre-programming codes Entering a pre-programming codeTV Mode TV Mode Operating your programmed remote controllerDVD Mode DVD Player Mode VCR Mode VCR ModeTo 6 inches To 15 cm Programming procedureIndicator Mode buttons Enter Send/LearnPage Press and release the same Mode button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Send/Learn indicator Mode buttons EnterExecuting the macro Using the macro functionProgramming the macro Erasing a macro from the Macro 1 or 2 button Using the macro functionErasing all commands and macros that have been programmed Macro Macro mode programming memoTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Amplifier Section Specifications DTR-6.3Specifications DTR-5.3 Onkyo U.S.A. Corporation