Integra DTR-5.3 IntelliVolume, Analog/PCM Source, PCM fs96kHz Source, Digital Format Source

Page 54

Input Setup

e. IntelliVolume

This setting allows you to adjust for the volume differences between your various input source components.

When switching input sources, you may find that the output level for different components or input sources connected to the DTR-6.3/5.3 is different even though the main volume setting is the same. Under normal circumstances, you would then have to change the volume setting each time you change the input source. This Intelli Volume setting allows you to preset a volume level for each input source separately so that when you do switch from one input source to another, the DTR-6.3/5.3 adjusts the volume accordingly and the volume stays the same. If the volume is quieter than that of other sources, increase it with the cursor button, and if it is louder than that of other sources, decrease it with the cursor button.

The Intelli Volume can be adjusted between –12 and +12 decibels.

f. Analog/PCM Source

This sets the listening mode for analog or PCM sources.

Analog sources consist of LP records, FM and AM broadcasts, cassette tapes, and the such. PCM (Pulse Code Modulation) is one form of digital audio signals and is recorded directly onto compact discs and DVDs without compression.

g. PCM fs96kHz Source

This sets the listening mode for Digital PCM sources recorded with a sampling rate of 96 kHz.

Note:

This setting will not appear if “----” is selected at the “Digital Input”

setting.

h. Digital Format Source

This sets the listening mode for Dolby Digital or DTS sources.

Note:

This setting will not appear if “----” is selected at the “Digital Input”

setting.

Relationship between input source and listening mode

i. Trigger A

This menu allows you to make the required settings to turn on the output from the 12V TRIGGER terminal to control another component or device with the DTR-6.3/5.3 for each input source.

On: Select to activate the device connected to the 12V TRIGGER A terminal when the input source is selected.

Off: Select when no device is connected to the 12V TRIGGER A terminal or you do not want the connected device to activate.

j. Trigger B

On: Select to activate the device connected to the 12V TRIGGER B terminal when the input source is selected.

Off: Select when no device is connected to the 12V TRIGGER B terminal or you do not want the connected device to activate.

Input source signal

Analog/PCM

PCM fs96kHz

 

Digital Format

 

(display)

(2ch)

 

Dolby Digital

DTS

2ch source

 

 

 

(Multichannel)

(Multichannel)

 

Type of software

Tape, CD, MD,

DVD

DVD

DVD

DVD

 

Record, Tuner,

(96k/24bit)

 

DTS-CD

Digital satellite

 

DVD (Stereo), LD,

 

 

 

 

 

Digital satellite

 

 

 

 

Listening Mode

(Stereo)

 

 

 

 

Direct

o

o

 

 

 

 

 

 

 

 

 

Pure Audio *1

o

o

 

 

 

Stereo

o

o

o

o

o

Dolby Pro Logic II

o

 

 

 

o *2

Dolby Digital

 

 

o

 

 

Dolby Digital EX

 

 

o

 

 

 

 

 

 

 

 

DTS Neo:6

o

 

 

 

 

 

 

 

 

 

 

DTS

 

 

 

o

 

DTS-ES Discrete

 

 

 

o

 

DTS-ES Matrix

 

 

 

o

 

Orchestra

o

 

 

 

 

 

 

 

 

 

 

Unplugged

o

 

 

 

 

 

 

 

 

 

 

Studio-Mix

o

 

 

 

 

 

 

 

 

 

 

TV Logic

o

 

 

 

 

All Ch Stereo

o

 

 

 

 

 

 

 

 

 

 

*1 DTR-6.3 only

*2 This mode is not available for DTS sources.

Note:

You may not be able to select all the listening modes shown here depending on your speaker configuration or the selected input source.

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents DTR-6.3/5.3 Important Safeguards AvisPrecautions Contents Contents Features DTR-6.3 Amplifier FeaturesInstalling the remote controller batteries Supplied accessoriesBefore using this unit Using the remote controllerFront panel facilities DTR-6.3 DTR-5.3Front panel facilities Speakers A/B buttons DTR-5.3 only Tuning indicators Muting indicatorListening mode or digital input format indicators Sleep indicatorRemote controller Remote controller Connections Connections Connecting a turntable Phono Connecting your audio componentsConnecting a compact disc player CD Signal flowFlow of the video signals is as follows Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Connections DTR-6.3Connecting a DVD Player with 2-Channel L/R Audio Output Connecting a DVD player DVDConnecting a video cassette recorder Video VideoConnecting a television monitor or projector Monitor OUT Monitor OUTFront right speaker Connecting video camera, etc. Video 4 InputPower amplifier Front left speaker Center speakerWhen using the Zone 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 PRE OUT terminals When using the Zone 2 OUT terminalsConnections DTR-5.3 CD player CDConnections DTR-5.3 Video outputConnections DTR-5.3 Video 2/3 Video output Digital output Optical DTR-6.3/5.3 12V Trigger OUT A/B Power cord supplied To an AC wall outletConnections DTR-6.3/5.3 DTR-6.3 only 12V Trigger OUT ZONE2Power on/ready function Power off functionDirect change function From connecting block DTR-6.3 onlyOther component Minimum speaker configuration for surround sound playback Connecting speakersStandard speaker setup for surround sound Speaker placementConnecting a subwoofer Connecting speakersConnecting speakers Connecting to the Speakers B terminals DTR-5.3 onlyFront Center Right Speaker Left Subwoofer SurroundRight Back Left Speaker Connecting the power Turning on the power from the remote controllerTurning on the power Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageConfiguring the speakers Speaker ConfigurationDisplaying the Main Menu Configuring the speakers Adjustable Crossover 80/100/120 Hz for Bass ManagementMeters Select if you will enter the distances in meters Calibrating the speaker levelsFeet Select if you will enter the distances in feet Use the and cursor buttons to select LeftUsing the remote controller Press the Test button Press the Test button to complete the procedureButtons used for navigating through the menus FM Mode Tuning Tuner Listening to a stereo radio station FM modeTuning into a radio station Listening to Radio BroadcastsErasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsBasic operation DTR-6.3 Adjust the volume to an appropriate levelSelecting an Audio Component Press the desired input sourceSelecting speakers Speakers A, B DTR-5.3 only Selecting an Audio ComponentBasic operation DTR-5.3 Speakers A/BSelecting the type of audio input signal Temporarily changing the speaker output levelsTo change the display of the input source from Tape to MD Sleep Audio Adjust Using the sleep time remote controller onlyListening with headphones Enjoying DVD multichannel audio playbackSwitching the display Temporarily turning off the soundListening Modes Listening Modes Tip Selecting a listening modeRcvr Mode Listening mode buttons While playing back Dolby Digital 2-channel sourcesPress the Cine Fltr button on the remote controller Original filter CinemaFILTER loading for moviesInput Setup Return Menu Input source buttons Return SetupInput Selector buttons Digital Format Input SetupDigital Input MultichannelPCM fs96kHz Source IntelliVolumeAnalog/PCM Source Digital Format SourceTo display the OSD Setup menu OSD Setup and Other SettingsOSD Setup PreferenceSetting Values Initial value Audio AdjustSetup Procedure Press the Audio Adjust button Bass, TrebleAudio Adjust Settings possible for each listening mode LateEx. When the CD button is pressed Using the buttons on the DTR-6.3Adjusting the volume for the remote zone Adjusting the volume using the remote controllerRecording a source DTR-6.3 Rec Out Off Input source buttonsStart recording at the recording component as desired Recording a source DTR-5.3 Rcvr Mode VOL Muting Using remote controllerCalling up a preset radio station Controlling an Onkyo cassette tape deckUsing remote controller Press the CD Mode buttonControlling an Integra/Onkyo CD player Top Menu Audio SEL Angle Standby DVD Mode Setup Press the DVD Mode buttonControlling an Integra/Onkyo DVD player Press the MD Mode button Controlling an Integra/Onkyo MD recorderTo 9, 0, --/--- Numeric keys Entering a pre-programming code Learning a pre-programming codeWithin 30 seconds, enter the 3-digit code number Entering a pre-programming code Pre-programming codesVCR Mode VCR Mode Operating your programmed remote controllerDVD Mode DVD Player Mode TV Mode TV ModeSend/Learn Programming procedureIndicator Mode buttons Enter To 6 inches To 15 cmPage Send/Learn indicator Mode buttons Enter Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againUsing the macro function Programming the macroExecuting the macro Using the macro function Erasing all commands and macros that have been programmedErasing a macro from the Macro 1 or 2 button Macro mode programming memo MacroTroubleshooting guide Troubleshooting guide Video and AudioIf one of the messages shown below appears Specifications DTR-6.3 Amplifier SectionSpecifications DTR-5.3 Onkyo U.S.A. Corporation
Top Page Image Contents