Integra DTR-5.3 instruction manual Buttons used for navigating through the menus

Page 40

Configuring the speakers

(1)Remember the volume level of this noise and then press the cursor button. The DTR-6.3/5.3 will now emit the pink noise from the center speaker.

(2)Using the and cursor buttons, adjust the volume level of the noise from the center speaker so that it is at the same level as that that was emitted from the front left speaker.

(3)Press the cursor button again. The DTR-6.3/5.3 will now emit the pink noise from the front right speaker.

Use the and cursor buttons to adjust the volume of the noise from the front left speaker so that it is the same level as that that was emitted from the center speaker.

(4)Use the cursor button to select other speakers and adjust the volumes until all speakers are adjusted to the same level.

The pink noise level can be adjusted to anywhere between –12 and +12 decibels for all speakers in 1-decibel increments.

Press the Return button to return to the main menu.

Press the Menu button on the front panel or Setup button on the remote controller button to exit the Setup menu.

Using the remote controller

1. Press the Test button.

You will hear a pink noise will be emitted from the front left speaker.

(1) Remember the volume level of this noise and then press the CH SEL button. The DTR-6.3/5.3 will now emit the pink noise from the center speaker.

(2) Using the Level / buttons, adjust the volume level of the noise from the center speaker so that it is at the same level as that that was emitted from the front left speaker.

(3)Press the CH SEL button again. The DTR-6.3/5.3 will now emit the pink noise from the front right speaker.

Use the Level / buttons to adjust the volume of the noise from the front left speaker so that it is the same level as that that was emitted from the center speaker.

(4)Use the CH SEL button to select other speakers and adjust the volumes until all speakers are adjusted to the same level.

The pink noise level can be adjusted to anywhere between –12 and +12 decibels for all speakers in 1-decibel increments.

2. Press the Test button to complete the procedure.

Buttons used for navigating through the menus

You can change settings in the Setup Menu using the buttons on the front panel and on the remote controller.

The buttons on the remote controller correspond to those on the DTR-6.3/5.3 as shown below.

Buttons on remote controller

Buttons on DTR-6.3/5.3

Displaying the Main Menu and exiting the menu

Setup

Menu

Selecting a menu or menu item

 

(upper edge of

Up

ENTER button)

 

(lower edge of

Down

ENTER button)

 

Setting the value

 

(left edge of

Left

ENTER button)

 

(right edge of

Right

ENTER button)

 

Selecting the menu

 

ENTER

Enter

Returning to the previous screen

 

Return

Return

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents DTR-6.3/5.3 Important Safeguards AvisPrecautions Contents Contents Features DTR-6.3 Amplifier FeaturesSupplied accessories Before using this unitInstalling the remote controller batteries Using the remote controllerFront panel facilities DTR-6.3 DTR-5.3Front panel facilities Speakers A/B buttons DTR-5.3 only Muting indicator Listening mode or digital input format indicatorsTuning indicators Sleep indicatorRemote controller Remote controller Connections Connections Connecting your audio components Connecting a compact disc player CDConnecting a turntable Phono Signal flowConnecting your video components Connecting a DVD Player with 5.1-Channel OutputFlow of the video signals is as follows Connections DTR-6.3Connecting a DVD Player with 2-Channel L/R Audio Output Connecting a DVD player DVDConnecting a video cassette recorder Video VideoConnecting a television monitor or projector Monitor OUT Monitor OUTConnecting video camera, etc. Video 4 Input Power amplifierFront right speaker Front left speaker Center speakerConnecting the remote zone Zone 2 speakers When using the Zone 2 PRE OUT terminalsWhen using the Zone 2 Speakers terminals When using the Zone 2 OUT terminalsConnections DTR-5.3 CD player CDConnections DTR-5.3 Video outputConnections DTR-5.3 Video 2/3 Video output Digital output Optical Power cord supplied To an AC wall outlet Connections DTR-6.3/5.3DTR-6.3/5.3 12V Trigger OUT A/B DTR-6.3 only 12V Trigger OUT ZONE2Power off function Power on/ready functionDirect change function DTR-6.3 only From connecting blockOther component Connecting speakers Standard speaker setup for surround soundMinimum speaker configuration for surround sound playback Speaker placementConnecting speakers Connecting speakersConnecting a subwoofer Connecting to the Speakers B terminals DTR-5.3 onlySubwoofer Surround Front Center Right Speaker LeftRight Back Left Speaker Turning on the power from the remote controller Connecting the powerTurning on the power Connecting antennas Connecting the AM antenna cableConnecting the included antennas Assembling the AM loop antennaConnecting antennas Connecting an FM outdoor antennaConnecting an AM outdoor antenna Directional linkageSpeaker Configuration Configuring the speakersDisplaying the Main Menu Configuring the speakers Adjustable Crossover 80/100/120 Hz for Bass ManagementCalibrating the speaker levels Feet Select if you will enter the distances in feetMeters Select if you will enter the distances in meters Use the and cursor buttons to select LeftPress the Test button to complete the procedure Using the remote controller Press the Test buttonButtons used for navigating through the menus Listening to a stereo radio station FM mode Tuning into a radio stationFM Mode Tuning Tuner Listening to Radio BroadcastsPresetting a radio station Selecting a preset radio stationErasing a preset radio station Listening to Radio BroadcastsAdjust the volume to an appropriate level Selecting an Audio ComponentBasic operation DTR-6.3 Press the desired input sourceSelecting an Audio Component Basic operation DTR-5.3Selecting speakers Speakers A, B DTR-5.3 only Speakers A/BTemporarily changing the speaker output levels Selecting the type of audio input signalTo change the display of the input source from Tape to MD Using the sleep time remote controller only Listening with headphonesSleep Audio Adjust Enjoying DVD multichannel audio playbackSwitching the display Temporarily turning off the soundListening Modes Listening Modes Selecting a listening mode Rcvr Mode Listening mode buttonsTip While playing back Dolby Digital 2-channel sourcesPress the Cine Fltr button on the remote controller Original filter CinemaFILTER loading for moviesReturn Menu Input source buttons Return Setup Input SetupInput Selector buttons Input Setup Digital InputDigital Format MultichannelIntelliVolume Analog/PCM SourcePCM fs96kHz Source Digital Format SourceOSD Setup and Other Settings OSD SetupTo display the OSD Setup menu PreferenceAudio Adjust Setup Procedure Press the Audio Adjust buttonSetting Values Initial value Bass, TrebleAudio Adjust Settings possible for each listening mode LateUsing the buttons on the DTR-6.3 Adjusting the volume for the remote zoneEx. When the CD button is pressed Adjusting the volume using the remote controllerRec Out Off Input source buttons Recording a source DTR-6.3Start recording at the recording component as desired Recording a source DTR-5.3 Using remote controller Calling up a preset radio stationRcvr Mode VOL Muting Controlling an Onkyo cassette tape deckPress the CD Mode button Using remote controllerControlling an Integra/Onkyo CD player Press the DVD Mode button Top Menu Audio SEL Angle Standby DVD Mode SetupControlling an Integra/Onkyo DVD player Controlling an Integra/Onkyo MD recorder Press the MD Mode buttonTo 9, 0, --/--- Numeric keys Learning a pre-programming code Entering a pre-programming codeWithin 30 seconds, enter the 3-digit code number Entering a pre-programming code Pre-programming codesOperating your programmed remote controller DVD Mode DVD Player ModeVCR Mode VCR Mode TV Mode TV ModeProgramming procedure Indicator Mode buttons EnterSend/Learn To 6 inches To 15 cmPage Erasing the programmed command from one button Erasing all the commands programmed under a Mode buttonSend/Learn indicator Mode buttons Enter Press and release the same Mode button againProgramming the macro Using the macro functionExecuting the macro Erasing all commands and macros that have been programmed Using the macro functionErasing a macro from the Macro 1 or 2 button Macro mode programming memo MacroTroubleshooting guide Troubleshooting guide Video and AudioIf one of the messages shown below appears Specifications DTR-6.3 Amplifier SectionSpecifications DTR-5.3 Onkyo U.S.A. Corporation
Top Page Image Contents