Integra instruction manual Specifications DTR-5.3

Page 79
Continuous power output (DIN) Maximum power output (EIAJ) Dynamic power output (stereo)
Total harmonic distortion: IM distortion:
Damping factor:
Input sensitivity and impedance LINE (CD, TAPE, DVD, VIDEO 1-4):
MULTICHANNEL INPUT (FRONT L/C/R, SURROUND L/R):
(SUBWOOFER):
COAXIAL (DIGITAL):
DVD, VIDEO 1, 2, 3, 4:
COMPONENT VIDEO 1, 2:
Output level and impedance Rec out (TAPE, VIDEO 1): Pre out:
VIDEO (VIDEO 1,
MONITOR OUT):
COMPONENT VIDEO OUT: Frequency response:
Tone control Bass: Treble:
Signal-to-noise ratio (stereo) CD/Tape:
Muting:

Specifications (DTR-5.3)

AMPLIFIER SECTION

Continuous average power output (FTC)

All channels:80 W per channel min. RMS at 8 Ω, 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion.

105 W min. RMS at 6 Ω, 2 channels driven from 1 kHz with no more than 0.1% total harmonic distortion. 115 W at 6 Ω

145 W at 6 Ω

2 ⋅ 215 W at 3 Ω

2 ⋅ 160 W at 4 Ω

2 ⋅ 95 W at 8 Ω

0.08% at rated power

0.08% at 1 W output

0.08% at rated power

0.08% at 1 W output

60 at 8 Ω

200 mV, 47 kΩ

200 mV, 47 kΩ

36 mV, 47 kΩ

0.5 Vp-p, 75 Ω

1 Vp-p, 75 Ω

1 Vp-p, 75 Ω (Y)

0.28 Vp-p, 75 Ω (C)

1 Vp-p, 75 Ω (Y)

0.7 Vp-p, 75 Ω (PB, PR)

200 mV, 470 Ω

1 V, 470 Ω

1 Vp-p, 75 Ω

1 Vp-p, 75 Ω (Y)

0.28 p-p, 75 Ω (C)

1 Vp-p, 75 Ω (Y)

0.7 Vp-p, 75 Ω (PB, PR)

10 Hz to 100 kHz : +1/–3 dB (CD in Direct mode)

TUNER SECTION

FM

Tuning range:

Usable sensitivity

Mono:

Stereo:

50 dB quieting sensitivity Mono:

Stereo: Capture ratio:

Image rejection ratio: IF rejection ratio: Signal-to-noise ratio

Mono:

Stereo:

Alternate channel attenuation: Selectivity:

AM suppression ratio: Total harmonic distortion

Mono:

Stereo: Frequency response: Stereo separation:

AM

Tuning range: Usable sensitivity: Image rejection ratio: IF rejection ratio: Signal-to-noise ratio: Total harmonic distortion:

GENERAL

Power supply: Power consumption: Dimensions (W ⋅ H ⋅ D): Weight:

REMOTE CONTROLLER

Transmitter:

Signal range:

Power supply:

87.5–108.0 MHz (50-kHz steps)

11.2dBf, 1.0 µV (75 Ω IHF)

0.9µV (75 Ω DIN)

17.2dBf, 2.0 µV (75 Ω IHF) 23 µV (75 Ω DIN)

17.2dBf, 2.0 µV (75 Ω)

37.2dBf, 20 µV (75 Ω)

2.0dB 40 dB 90 dB

76dB

70dB

55dB

50dB (DIN)

50dB

0.2%

0.3%

30Hz–15 kHz, ±1.0 dB

45dB at 1 kHz

30dB at 100 Hz–10 kHz

530to 1,710 kHz (10-kHz steps)

30µV

40dB

40dB

40dB 0.7%

AC 120 V, 60 Hz 5.5 A

17-1/8" ⋅ 6-7/8" ⋅ 17"

24.3 lbs.

Infrared

Approx. 16 ft., 5 meters

Two “AA” batteries (1.5 V ⋅ 2)

±12 dB at 50 Hz ±12 dB at 20,000 Hz

100 dB (IHF A, 0.5 V input)

–50 dB

Specifications and features are subject to change without notice.

79

Page 78 Page 80
Image 79
Page 78 Page 80
Contents DTR-6.3/5.3 Avis Important SafeguardsPrecautions Contents Contents DTR-6.3 Amplifier Features FeaturesUsing the remote controller Supplied accessoriesBefore using this unit Installing the remote controller batteriesDTR-6.3 DTR-5.3 Front panel facilitiesFront panel facilities Speakers A/B buttons DTR-5.3 only Sleep indicator Muting indicatorListening mode or digital input format indicators Tuning indicatorsRemote controller Remote controller Connections Connections Signal flow Connecting your audio componentsConnecting a compact disc player CD Connecting a turntable PhonoConnections DTR-6.3 Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Flow of the video signals is as followsConnecting a DVD player DVD Connecting a DVD Player with 2-Channel L/R Audio OutputVideo Connecting a video cassette recorder VideoMonitor OUT Connecting a television monitor or projector Monitor OUTFront left speaker Center speaker Connecting video camera, etc. Video 4 InputPower amplifier Front right speakerWhen using the Zone 2 OUT terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 PRE OUT terminals When using the Zone 2 Speakers terminalsCD player CD Connections DTR-5.3Video output Connections DTR-5.3Connections DTR-5.3 Video 2/3 Video output Digital output Optical DTR-6.3 only 12V Trigger OUT ZONE2 Power cord supplied To an AC wall outletConnections DTR-6.3/5.3 DTR-6.3/5.3 12V Trigger OUT A/BPower off function Power on/ready functionDirect change function DTR-6.3 only From connecting blockOther component Speaker placement Connecting speakersStandard speaker setup for surround sound Minimum speaker configuration for surround sound playbackConnecting to the Speakers B terminals DTR-5.3 only Connecting speakersConnecting speakers Connecting a subwooferSubwoofer Surround Front Center Right Speaker LeftRight Back Left Speaker Turning on the power from the remote controller Connecting the powerTurning on the power Assembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaSpeaker Configuration Configuring the speakersDisplaying the Main Menu Adjustable Crossover 80/100/120 Hz for Bass Management Configuring the speakersUse the and cursor buttons to select Left Calibrating the speaker levelsFeet Select if you will enter the distances in feet Meters Select if you will enter the distances in metersPress the Test button to complete the procedure Using the remote controller Press the Test buttonButtons used for navigating through the menus Listening to Radio Broadcasts Listening to a stereo radio station FM modeTuning into a radio station FM Mode Tuning TunerListening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationPress the desired input source Adjust the volume to an appropriate levelSelecting an Audio Component Basic operation DTR-6.3Speakers A/B Selecting an Audio ComponentBasic operation DTR-5.3 Selecting speakers Speakers A, B DTR-5.3 onlyTemporarily changing the speaker output levels Selecting the type of audio input signalTo change the display of the input source from Tape to MD Enjoying DVD multichannel audio playback Using the sleep time remote controller onlyListening with headphones Sleep Audio AdjustTemporarily turning off the sound Switching the displayListening Modes Listening Modes While playing back Dolby Digital 2-channel sources Selecting a listening modeRcvr Mode Listening mode buttons TipOriginal filter CinemaFILTER loading for movies Press the Cine Fltr button on the remote controllerReturn Menu Input source buttons Return Setup Input SetupInput Selector buttons Multichannel Input SetupDigital Input Digital FormatDigital Format Source IntelliVolumeAnalog/PCM Source PCM fs96kHz SourcePreference OSD Setup and Other SettingsOSD Setup To display the OSD Setup menuBass, Treble Audio AdjustSetup Procedure Press the Audio Adjust button Setting Values Initial valueAudio Adjust Late Settings possible for each listening modeAdjusting the volume using the remote controller Using the buttons on the DTR-6.3Adjusting the volume for the remote zone Ex. When the CD button is pressedRec Out Off Input source buttons Recording a source DTR-6.3Start recording at the recording component as desired Recording a source DTR-5.3 Controlling an Onkyo cassette tape deck Using remote controllerCalling up a preset radio station Rcvr Mode VOL MutingPress the CD Mode button Using remote controllerControlling an Integra/Onkyo CD player Press the DVD Mode button Top Menu Audio SEL Angle Standby DVD Mode SetupControlling an Integra/Onkyo DVD player Controlling an Integra/Onkyo MD recorder Press the MD Mode buttonTo 9, 0, --/--- Numeric keys Learning a pre-programming code Entering a pre-programming codeWithin 30 seconds, enter the 3-digit code number Pre-programming codes Entering a pre-programming codeTV Mode TV Mode Operating your programmed remote controllerDVD Mode DVD Player Mode VCR Mode VCR ModeTo 6 inches To 15 cm Programming procedureIndicator Mode buttons Enter Send/LearnPage Press and release the same Mode button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Send/Learn indicator Mode buttons EnterProgramming the macro Using the macro functionExecuting the macro Erasing all commands and macros that have been programmed Using the macro functionErasing a macro from the Macro 1 or 2 button Macro Macro mode programming memoTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Amplifier Section Specifications DTR-6.3Specifications DTR-5.3 Onkyo U.S.A. Corporation
Top Page Image Contents