Integra DTR-5.3 instruction manual DTR-6.3 only, From connecting block, Other component

Page 30

Operating components not reached by the remote controller signals (IR IN) (DTR-6.3/5.3)

In order to use the remote controller to control the DTR-6.3/5.3 from a remote location, you will need to prepare a multi-room kit (sold separately) such as one of those given below:

•Onkyo’s Multi-Room System kit (IR Remote Controller Extension System)

•Multiroom A/V distribution and control system such as those from Niles® and Xantech®

If the remote controller signal does not reach the DTR-6.3/5.3 remote sensor

If the DTR-6.3/5.3 is located inside a cabinet or other enclosure where the infrared rays from the remote controller cannot enter, then operation with the remote controller will not be possible. In such a case, it will be necessary to install a remote sensor at a location outside of the cabinet where the infrared rays from the controller can reach.

DTR-6.3 only:

With this connection, select “Main” at “Preference” → “IR IN Position” (see page 56).

Make the connections as shown below. Do not plug in any equipment to the power outlet until all the connections are complete.

From connecting block

Mini plug cable

REMOTE

CONTROL

IR

OUT

IN

DTR-6.3

If the remote controller signal does not reach other components

IR IN

DTR-6.3/5.3

Connecting

IR Receiver

block

 

Remote Controller

In this situation, you will need to use a commercially available IR emitter. Connect the mini plug of the IR emitter to the IR OUT terminal on the DTR-6.3/5.3 and then place the IR emitter on the remote sensor of the component or facing it. When the IR emitter is connected, only the signal input to the IR IN terminal is output to the IR OUT terminal. The signal input from the remote sensor on the front of the DTR-6.3/5.3 will not be output to the IR OUT terminal.

In the cabinet

Connecting block

IR IN

IR Receiver

DTR-6.3/5.3

: Signal flow

DTR-6.3 only:

The IR IN input allows you to control the DTR-6.3 from the remote zone (Zone 2) with the remote controller even though the remote zone may be on the other side of the building from the main zone. The diagram below shows how to make the proper connections for the remote zone.

With this connection, select “Zone 2” at “Preference” → “IR IN Position” (see page 56).

To IR IN

IR Receiver

DTR-6.3

Connecting block

Remote controller

Main room

Zone 2 room

: Signal flow

IR OUT

IR Emitter

Remote Controller

other component

: Signal flow

other component

Remote control sensor

Emitter

: Signal flow

Mini plug cable

Mini plug

REMOTE

CONTROL

IR

OUT

IN

IR Emitter

DTR-6.3/5.3

 

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents DTR-6.3/5.3 Important Safeguards AvisPrecautions Contents Contents Features DTR-6.3 Amplifier FeaturesInstalling the remote controller batteries Supplied accessoriesBefore using this unit Using the remote controllerFront panel facilities DTR-6.3 DTR-5.3Front panel facilities Speakers A/B buttons DTR-5.3 only Tuning indicators Muting indicatorListening mode or digital input format indicators Sleep indicatorRemote controller Remote controller Connections Connections Connecting a turntable Phono Connecting your audio componentsConnecting a compact disc player CD Signal flowFlow of the video signals is as follows Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Connections DTR-6.3Connecting a DVD Player with 2-Channel L/R Audio Output Connecting a DVD player DVDConnecting a video cassette recorder Video VideoConnecting a television monitor or projector Monitor OUT Monitor OUTFront right speaker Connecting video camera, etc. Video 4 InputPower amplifier Front left speaker Center speakerWhen using the Zone 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 PRE OUT terminals When using the Zone 2 OUT terminalsConnections DTR-5.3 CD player CDConnections DTR-5.3 Video outputConnections DTR-5.3 Video 2/3 Video output Digital output Optical DTR-6.3/5.3 12V Trigger OUT A/B Power cord supplied To an AC wall outletConnections DTR-6.3/5.3 DTR-6.3 only 12V Trigger OUT ZONE2Power on/ready function Power off functionDirect change function From connecting block DTR-6.3 onlyOther component Minimum speaker configuration for surround sound playback Connecting speakersStandard speaker setup for surround sound Speaker placementConnecting a subwoofer Connecting speakersConnecting speakers Connecting to the Speakers B terminals DTR-5.3 onlyFront Center Right Speaker Left Subwoofer SurroundRight Back Left Speaker Connecting the power Turning on the power from the remote controllerTurning on the power Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageConfiguring the speakers Speaker ConfigurationDisplaying the Main Menu Configuring the speakers Adjustable Crossover 80/100/120 Hz for Bass ManagementMeters Select if you will enter the distances in meters Calibrating the speaker levelsFeet Select if you will enter the distances in feet Use the and cursor buttons to select LeftUsing the remote controller Press the Test button Press the Test button to complete the procedureButtons used for navigating through the menus FM Mode Tuning Tuner Listening to a stereo radio station FM modeTuning into a radio station Listening to Radio BroadcastsErasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsBasic operation DTR-6.3 Adjust the volume to an appropriate levelSelecting an Audio Component Press the desired input sourceSelecting speakers Speakers A, B DTR-5.3 only Selecting an Audio ComponentBasic operation DTR-5.3 Speakers A/BSelecting the type of audio input signal Temporarily changing the speaker output levelsTo change the display of the input source from Tape to MD Sleep Audio Adjust Using the sleep time remote controller onlyListening with headphones Enjoying DVD multichannel audio playbackSwitching the display Temporarily turning off the soundListening Modes Listening Modes Tip Selecting a listening modeRcvr Mode Listening mode buttons While playing back Dolby Digital 2-channel sourcesPress the Cine Fltr button on the remote controller Original filter CinemaFILTER loading for moviesInput Setup Return Menu Input source buttons Return SetupInput Selector buttons Digital Format Input SetupDigital Input MultichannelPCM fs96kHz Source IntelliVolumeAnalog/PCM Source Digital Format SourceTo display the OSD Setup menu OSD Setup and Other SettingsOSD Setup PreferenceSetting Values Initial value Audio AdjustSetup Procedure Press the Audio Adjust button Bass, TrebleAudio Adjust Settings possible for each listening mode LateEx. When the CD button is pressed Using the buttons on the DTR-6.3Adjusting the volume for the remote zone Adjusting the volume using the remote controllerRecording a source DTR-6.3 Rec Out Off Input source buttonsStart recording at the recording component as desired Recording a source DTR-5.3 Rcvr Mode VOL Muting Using remote controllerCalling up a preset radio station Controlling an Onkyo cassette tape deckUsing remote controller Press the CD Mode buttonControlling an Integra/Onkyo CD player Top Menu Audio SEL Angle Standby DVD Mode Setup Press the DVD Mode buttonControlling an Integra/Onkyo DVD player Press the MD Mode button Controlling an Integra/Onkyo MD recorderTo 9, 0, --/--- Numeric keys Entering a pre-programming code Learning a pre-programming codeWithin 30 seconds, enter the 3-digit code number Entering a pre-programming code Pre-programming codesVCR Mode VCR Mode Operating your programmed remote controllerDVD Mode DVD Player Mode TV Mode TV ModeSend/Learn Programming procedureIndicator Mode buttons Enter To 6 inches To 15 cmPage Send/Learn indicator Mode buttons Enter Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againUsing the macro function Programming the macroExecuting the macro Using the macro function Erasing all commands and macros that have been programmedErasing a macro from the Macro 1 or 2 button Macro mode programming memo MacroTroubleshooting guide Troubleshooting guide Video and AudioIf one of the messages shown below appears Specifications DTR-6.3 Amplifier SectionSpecifications DTR-5.3 Onkyo U.S.A. Corporation
Top Page Image Contents