Integra DTR-5.6 Advanced Setup, Speaker Setup menu appears, Speaker Config menu appears

Page 63

DTR-5.6.book Page 63 Thursday, September 22, 2005 5:07 PM

Advanced Setup

Speaker Setup

2

This section explains how to check the speaker settings and how to set them manually, which is useful if you change a speaker after performing the automatic speaker setup.

Some speaker settings are set automatically by the Auto- matic Speaker Setup function (see page 37).

Use the Up and Down []/[ ] buttons to select “3. Speaker Setup,” and then press [Enter].

The Speaker Setup menu appears.

Receiver

Enter

Speaker Configuration

3

Setup

4

Use the Up and Down []/[ ] buttons to select “Speaker Con- figuration,” and then press [Enter].

The Speaker Config menu appears.

3-2.Speaker Config

------------------------

a.Subwoofer

:Yes

b.Front

:Large

c.Center

:Small

d.Surround

:Small

e.SurroundBack :Small

f.SurrBack Ch

:2ch

g.Crossover

:100Hz

h.Subwoofer Mode :-------------

Use the Up and Down []/[ ] buttons to select “a. Subwoofer,” and then use the Left and Right []/[ ] buttons to select:

This setting is set automatically by the Automatic Speaker Setup function (see page 37).

Here you can specify which speakers are connected and

their individual sizes.

5

 

For speakers with a cone diameter

 

over 6-1/2 inches (16 cm), specify

 

large, and for those with a diameter

 

below this, specify small.

 

 

Cone diameter

 

1

Press the [Receiver] Remote

 

 

 

 

Mode button, followed by the

 

 

[Setup] button.

 

The main menu appears onscreen.

Yes: Select if a subwoofer is con- nected.

No: Select if no subwoofer is con- nected.

Use the Up and Down []/[ ] buttons to select “b. Front,” and then use the Left and Right

[]/[ ] buttons to select:

Small: Select if the front speakers are small.

Large: Select if the front speakers are large.

Note:

•If the Subwoofer setting in step 4 is set to No, this setting is fixed at Large.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents DTR-5.6 Avis Important Safety InstructionsPower PrecautionsMake sure you have the following accessories Supplied AccessoriesContents Features Before Using the AV receiver Installing the BatteriesUsing the Remote Controller Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverIR in A/B and OUT Rear PanelComponent Video in 1, 2, XM antenna on North American modelThese terminal posts are for connecting speakers in Zone Video 1 IN/OUT and Video 2 IN/OUTFRONT, CENTER, SURROUND, Remote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Enjoying Home Theater Connecting Your SpeakersConnecting Your Speakers Connecting Your SpeakersSpeaker Connection Precautions Connecting the Speaker CablesStrip about 5/8 Attach the FM antenna, as shown American Model Connecting AntennaConnecting the AM Loop Antenna Connecting the Indoor FM AntennaUsing a TV/FM Antenna Splitter Connecting AntennaConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaAV Connection Color Coding Connecting Your ComponentsAbout AV Connections Optical Digital JacksVideo Connection Formats Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Which Connections Should I Use?Hint Connecting a TV or ProjectorVideo Connection Audio ConnectionConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Step Connecting a CD PlayerTurntable without a Built-in Phono Preamp Connecting a TurntableConnecting a Power Amplifier Connecting a Cassette, CDR, MiniDisc, or DAT RecorderAuto Power On/Standby Connecting ComponentsStandby indicator lights up Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Connecting the Power CordSmooth Operation in a Few Easy Steps Do the automatic speaker setup-this is essentialTurning On the AV Receiver Turning On and StandbyConnected TV Put the speaker setup microPhone in the listening position Turn on the AV receiverOn completion, the following menu appears First Time SetupDisconnect the speaker setup Press EnterChecking the Results Press the Receiver button, fol Component Video SetupLowed by the Setup button Press the Setup buttonButtons to select 2. Digital Digital Audio Input SetupSetup closes Use the Up and DownMinimum Speaker Impedance Changing the Input DisplayYou must specify the TV system used in your area TV Format Setup Not North American modelsAM Frequency Step Setup on some models Hardware Setup menu appearsBasic AV Receiver Operation Select a listening mode and enjoySee Using the Listening Modes on Playing Your AV ComponentsDisplaying AM/FM Radio Information Tuning into AM/FM Radio StationsListening to the Radio Listening to AM/FM StationsConnecting the XM Antenna Listening to the RadioSigning Up for XM Satellite Radio Use the Up and Down Buttons to select a channel Channel Search modeMode button, followed by Selecting XM Radio ChannelsNel Displaying XM Radio InformationSelecting XM Channels from the Front Panel Buttons to select a chanXM Radio Messages Positioning the XM AntennaXM Channels Presetting AM/FM StationsSelecting Presets Deleting PresetsInput Channel Using the Multichannel DVD InputUsing the Multichannel DVD Input Multichannel DVD Input SettingsMuting the AV Receiver Adjusting Speaker LevelsSetting the Display Brightness Common FunctionsDisplaying Source Information Using the Sleep TimerUsing Headphones Common FunctionsSelecting on the AV Receiver Using the Listening ModesSelecting with the Remote Controller Selecting the Listening ModesDVD Using the Listening ModesSound is output by the front left and right speakers Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS About the Listening ModesRecording Recording Audio and Video from Separate SourcesRecording the Input Source About the Onscreen Setup Menus Onscreen Setup MenusAdjusting the Listening Modes Audio Adjust MenuUsing the Cine Filter Function Neo6 Music Adjusting the Listening ModesTone Control Settings PL IIx and Neo6 Settings PL IIx Music 2 ch onlyMultiplex Dolby Digital SettingsMono/Multiplex Settings LFE Level SettingOptions for that input selector Appear Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningSpeaker Config menu appears Advanced SetupSpeaker Setup Speaker Setup menu appearsCrossover Advanced SetupSubwoofer Mode Speaker DistanceSpeaker Distance menu appears Speaker is the same Repeat so that the volumeSpeaker Level Calibration Test tone from eachTings option to Equalizer SettingsRepeat steps 6 and 7 for each speaker Buttons to set the a. Use SetDelay Input SetupIntelliVolume Volume SetupPreferences OSD Position OSD Setup12V Trigger A/B/C Setup Lock SetupChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID Opt or coax, and then press Digital Input Signal FormatsButtons to select an input source That’s assigned to a digital inputZone Connecting ZoneUsing Another Amp in Zone Using Only Speakers in ZoneZone 2 Out Setting Powered Zone 2 SettingUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV Receiver Level+ buttons Zone 2 Remote Mode butTo adjust Ton, and then use the Level12V Trigger Setting for Each Input Source Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting DelayUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Controlling Other Components Entering Remote Control CodesControlling Other Components Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Resetting the Remote Mode ButtonsTV Input On, Standby, TVCH +/-, TV CH + Prev CHLearning Commands from Other Remote Controllers Deleting Macros Using MacrosMaking Macros Running MacrosTroubleshooting Troubleshooting Can’t control other components Remote controller doesn’t workCan’t learn commands from another remote controller Sound changes when I connect my head- phonesVideo Section SpecificationAmplifier Section General3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents