Integra DTR-5.6 Remote controller doesn’t work, Can’t control other components, Can’t record

Page 86

DTR-5.6.book Page 86 Thursday, September 22, 2005 5:07 PM

Troubleshooting—Continued

Remote Controller

The remote controller doesn’t work

•Make sure that the batteries are installed with the cor- rect polarity (page 7).

•Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor (page 7).

•Make sure you’ve selected the correct remote control- ler mode (page 12).

•Make sure you’ve entered the correct remote control code (page 79).

Can’t control other components

•Make sure you’ve selected the correct remote control- ler mode (page 12).

•If you’ve connected an -capable Integra MD recorder, CD recorder, or next generation HDD-com- patible component to the TAPE IN/OUT jacks, or an Onkyo DS-A1 Remote Interactive Dock to the VIDEO 3 IN jacks, for the remote controller to work properly, you must set the input display to MD, CDR, or HDD (see page 42).

•The entered remote control code may not be correct. If more than one code is listed, try each one.

•If none of the codes work, use the Learning function to learn the commands of the other component’s remote controller (page 82).

•With some AV components, certain buttons may not work as expected, and some may not work at all.

•To control an Integra component that’s connected via

, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first (page 80).

•To control an Integra component that’s not connected

via , or another manufacturer’s component, point the remote controller at the component. Be sure to enter the appropriate remote control code first (page 79).

Can’t learn commands from another remote controller

•When learning commands, make sure that the trans- mitting ends of both remote controllers are pointing at each other.

•Are you trying to learn from a remote controller that cannot be used for learning? Some commands cannot be learned, especially those that contain several instructions.

Recording

Can’t record

•On your recorder, make sure the correct input is selected.

•To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e.g., TAPE IN to TAPE OUT, VIDEO 1 IN to VIDEO 1 OUT, or VIDEO 2 IN to VIDEO 2 OUT).

Others

The sound changes when I connect my head- phones

•When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct, in which case it stays the same.

How do I change the language of a multiplex source

•Use the “Multiplex” setting on the “Audio Adjust” menus to select “Main” or “Sub” (page 61).

The functions don’t work

•To use , you must make an connection and an analog audio connection (RCA) between the compo- nent and AV receiver, even if they are connected digi- tally (page 34).

•While Zone 2 is on, the functions do not work.

The AV receiver contains a microcomputer for signal pro- cessing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded cor- rectly.

To reset the AV receiver to its factory defaults, turn it on and, while holding down the [Video 1] button, press the [Standby/On] button. “Clear” will appear on the display and the AV receiver will enter Standby mode.

Set the AV receiver to Standby before disconnecting the power cord from the wall outlet.

86

Page 85 Page 87
Image 86
Page 85 Page 87
Contents DTR-5.6 Important Safety Instructions AvisPrecautions PowerSupplied Accessories Make sure you have the following accessoriesContents Features Using the Remote Controller Before Using the AV receiverInstalling the Batteries Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna on North American model Rear PanelComponent Video in 1, 2, IR in A/B and OUTFRONT, CENTER, SURROUND, These terminal posts are for connecting speakers in ZoneVideo 1 IN/OUT and Video 2 IN/OUT Receiver/Tape Mode Remote ControllerAbout the Remote Controller Modes Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersStrip about 5/8 Speaker Connection PrecautionsConnecting the Speaker Cables Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a CD Player StepConnecting a Turntable Turntable without a Built-in Phono PreampConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Power AmplifierConnecting Components Auto Power On/StandbyConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the automatic speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsTurn on the AV receiver Put the speaker setup microPhone in the listening position Connected TVPress Enter First Time SetupDisconnect the speaker setup On completion, the following menu appearsChecking the Results Press the Setup button Component Video SetupLowed by the Setup button Press the Receiver button, folUse the Up and Down Digital Audio Input SetupSetup closes Buttons to select 2. DigitalChanging the Input Display Minimum Speaker ImpedanceHardware Setup menu appears TV Format Setup Not North American modelsAM Frequency Step Setup on some models You must specify the TV system used in your areaPlaying Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationSigning Up for XM Satellite Radio Connecting the XM AntennaListening to the Radio Selecting XM Radio Channels Channel Search modeMode button, followed by Use the Up and Down Buttons to select a channelButtons to select a chan Displaying XM Radio InformationSelecting XM Channels from the Front Panel NelPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Input ChannelCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DVDAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Sound is output by the front left and right speakersRecording the Input Source RecordingRecording Audio and Video from Separate Sources Onscreen Setup Menus About the Onscreen Setup MenusUsing the Cine Filter Function Adjusting the Listening ModesAudio Adjust Menu PL IIx and Neo6 Settings PL IIx Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexUse the Up and Down Buttons to select 5. Listening Default Listening ModesListening Mode Preset menu Appears Options for that input selector AppearSpeaker Setup menu appears Advanced SetupSpeaker Setup Speaker Config menu appearsAdvanced Setup CrossoverSpeaker Distance menu appears Subwoofer ModeSpeaker Distance Test tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameButtons to set the a. Use Set Equalizer SettingsRepeat steps 6 and 7 for each speaker Tings option toInput Setup DelayPreferences IntelliVolumeVolume Setup Lock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionChanging the AV Receiver’s Remote ID Changing the Remote Controller’s IDRemote IDs That’s assigned to a digital input Digital Input Signal FormatsButtons to select an input source Opt or coax, and then pressUsing Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingControlling Zone 2 from the AV Receiver Using ZoneControlling Zone 2 with the Remote Controller Ton, and then use the Level Zone 2 Remote Mode butTo adjust Level+ buttonsDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Other Components Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Zone Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents