Integra DTR-5.6 instruction manual OSD Setup, OSD Position, 12V Trigger A/B/C Setup, Lock Setup

Page 70

DTR-5.6.book Page 70 Thursday, September 22, 2005 5:07 PM

Advanced Setup—Continued

■Power On Vol / Z2 Power On Vol

With these preferences, you can specify the volume set- tings to be used in the main room and Zone 2 when the AV receiver is turned on.

When the Volume Display preference is set to Absolute, the range of “Power On Vol” is 0 to 100 (“Z2 Power On Vol” is 0 to 82). When it’s set to Relative, the range of “Power On Vol” is –∞dB, –81 dB to +18 dB (“Z2 Power On Vol” is –∞dB, –81 dB to 0 dB).

To use the same volume level as when the AV receiver was turned off, select “Last.”

The “Power On Vol” cannot be set higher than the “Max- imum Vol” setting.

■Headphones Level

With this preference, you can specify the headphone vol- ume relative to the main volume. This is useful if there’s a volume difference between your speakers and your headphones. The headphones level can be set from –12 dB to +12 dB.

OSD Setup

■Scan Mode

If the text in the onscreen setup menus flickers due to compatibility issues with your TV or projector, select Non-Interlaced.

Interlaced: Default.

Non-Interlaced:Select if the menu text flickers. With some TVs or projectors, the onscreen setup menus may not appear when “Non-Interlaced” is selected. In this case, select this setting again by using the AV receiver’s display, and select “Interlaced.”

Immediate

These settings determine how the operation details are displayed.

■Immediate Display

This preference determines whether operation details are displayed onscreen when an AV receiver function is adjusted.

On: Displayed (default).

Off: Not displayed.

Even when On is selected, operation details are not out- put if the input source is connected to a COMPONENT VIDEO IN.

■Monitor Type

With this preference, you can specify the aspect ratio of your TV so that the operation details are displayed prop- erly.

4:3: Select if your TV is 4:3 (default). 16:9: Select if your TV is 16:9.

■Display Position

OSD Position

With this preference, you can specify the position of the onscreen setup menus. This is useful with TVs or projec- tors where the menus don’t appear in the center of the screen, or part of the menu is cut off.

To set the menu position, use the arrow [ ]/[ ]/

[ ]/[ ] buttons. To set it back to its default position, press [ENTER].

12V Trigger A/B/C Setup

See page 77.

Lock Setup

■Lock

With this preference, you can protect your settings by locking the setup menus.

When the setup menus are locked, only settings on the Audio Adjust menu can be changed.

Locked: Setup menus locked. Unlocked: Setup menus not locked.

This preference determines where on the screen opera- tion details are displayed.

Bottom: Bottom of the screen (default). Top: Top of the screen.

70

Page 69 Page 71
Image 70
Page 69 Page 71
Contents DTR-5.6 Important Safety Instructions AvisPrecautions PowerSupplied Accessories Make sure you have the following accessoriesContents Features Installing the Batteries Before Using the AV receiverUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna on North American model Rear PanelComponent Video in 1, 2, IR in A/B and OUTVideo 1 IN/OUT and Video 2 IN/OUT These terminal posts are for connecting speakers in ZoneFRONT, CENTER, SURROUND, About the Remote Controller Modes Remote ControllerReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersConnecting the Speaker Cables Speaker Connection PrecautionsStrip about 5/8 Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a CD Player StepConnecting a Turntable Turntable without a Built-in Phono PreampConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Power AmplifierConnecting Components Auto Power On/StandbyConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the automatic speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsTurn on the AV receiver Put the speaker setup microPhone in the listening position Connected TVPress Enter First Time SetupDisconnect the speaker setup On completion, the following menu appearsChecking the Results Press the Setup button Component Video SetupLowed by the Setup button Press the Receiver button, folUse the Up and Down Digital Audio Input SetupSetup closes Buttons to select 2. DigitalChanging the Input Display Minimum Speaker ImpedanceHardware Setup menu appears TV Format Setup Not North American modelsAM Frequency Step Setup on some models You must specify the TV system used in your areaPlaying Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationListening to the Radio Connecting the XM AntennaSigning Up for XM Satellite Radio Selecting XM Radio Channels Channel Search modeMode button, followed by Use the Up and Down Buttons to select a channelButtons to select a chan Displaying XM Radio InformationSelecting XM Channels from the Front Panel NelPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Input ChannelCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DVDAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Sound is output by the front left and right speakersRecording Audio and Video from Separate Sources RecordingRecording the Input Source Onscreen Setup Menus About the Onscreen Setup MenusAudio Adjust Menu Adjusting the Listening ModesUsing the Cine Filter Function PL IIx and Neo6 Settings PL IIx Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexUse the Up and Down Buttons to select 5. Listening Default Listening ModesListening Mode Preset menu Appears Options for that input selector AppearSpeaker Setup menu appears Advanced SetupSpeaker Setup Speaker Config menu appearsAdvanced Setup CrossoverSpeaker Distance Subwoofer ModeSpeaker Distance menu appears Test tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameButtons to set the a. Use Set Equalizer SettingsRepeat steps 6 and 7 for each speaker Tings option toInput Setup DelayVolume Setup IntelliVolumePreferences Lock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionRemote IDs Changing the Remote Controller’s IDChanging the AV Receiver’s Remote ID That’s assigned to a digital input Digital Input Signal FormatsButtons to select an input source Opt or coax, and then pressUsing Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingControlling Zone 2 with the Remote Controller Using ZoneControlling Zone 2 from the AV Receiver Ton, and then use the Level Zone 2 Remote Mode butTo adjust Level+ buttonsDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents