Integra DTR-5.6 Specification, Amplifier Section, General, Video Section, Tuner Section

Page 87

DTR-5.6.book Page 87 Thursday, September 22, 2005 5:07 PM

Specification

Amplifier Section

Power Output

2 channels driven:

90 W + 90 W (8 Ω, 20 Hz–20 kHz, FTC)

 

155 W + 155 W (6 Ω, 1 kHz, JEITA)

Dynamic Power

225 W + 225 W (3 Ω, Front)

 

170 W + 170 W (4 Ω, Front)

 

105 W + 105 W (8 Ω, Front)

THD (Total Harmonic

 

Distortion)

0.08% (Power Rated)

Damping Factor

60 (Front, 1 kHz, 8Ω)

Input Sensitivity and

200 mV/ 47 kΩ (LINE)

Impedance

Output Level and

200 mV/ 470 Ω (REC OUT)

Impedance

Frequency Response

5 Hz–100 kHz/ +1 dB-3 dB (LINE)

Tone Control

±10 dB, 50 Hz (BASS)

 

±10 dB, 20 kHz (TREBLE)

Signal to Noise Ratio

100 dB (LINE, IHF-A)

Speaker Impedance

4Ω– or 6Ω–

General

Power Supply

North American: AC 120 V, 60 Hz

 

Australian: AC 230-240 V, 50 Hz

Power Consumption

North American: 6.7 A

 

Australian: 570 W

Standby Power

 

Consumption

North American: 0.1 W

 

Australian: 0.5 W

Dimensions

 

(W ⋅ H ⋅ D)

435 ⋅ 173.5 ⋅ 428.5 mm

 

17-1/8" ⋅ 6-13/16" ⋅ 16-7/8"

Weight

11.9 kg

 

26.2 lbs.

■Video Inputs

Component

IN1, IN2, IN3

S-Video

DVD, VIDEO1, VIDEO2, VIDEO3,

 

VIDEO4

Composite

DVD, VIDEO1, VIDEO2, VIDEO3,

 

VIDEO4

Video Section

Input Sensitivity/Output

Level and Impedance 1 Vp-p /75Ω(Component and S-Video Y)

0.7Vp-p /75Ω(Component Pb/Cb,Pr/Cr)

0.28Vp-p /75Ω(S-Video C) 1 Vp-p /75Ω(Composite)

Component Video

 

Frequency Response

5 Hz – 100 MHz

Tuner Section

■FM

Tuning Frequency Range North American: 87.5 MHz– 107.9 MHz

 

Australian: 87.5 MHz– 108.0 MHz

Usable Sensitivity

Stereo: 22.2 dBf (75Ω IHF)

 

Mono: 15.2 dBf (75Ω IHF)

Signal to Noise Ratio

Stereo: 67 dB (IHF-A)

 

Mono: 73 dB (IHF-A)

THD

Stereo: 0.5% (1 kHz)

 

Mono:0.3% (1 kHz)

Frequency Response

30 Hz–15 kHz / ±1 dB

Stereo Separation

40 dB (1 kHz)

■AM

Tuning Frequency Range North American: 530 kHz–1710 kHz

 

Australian: 522/530 kHz–1611/1710 kHz

Usable Sensitivity

300 µV/m

Signal to Noise Ratio

40 dB

THD

0.70%

■Video Outputs

Component

OUT

S-Video

MONITOR OUT, VIDEO1, VIDEO2

Composite

MONITOR OUT, VIDEO1, VIDEO2

■Audio Inputs

Digital Inputs

Optical: 4 (1 on Front Panel)

 

Coaxial: 2

Analog Inputs

DVD (MULTICHANNEL), VIDEO1,

 

VIDEO2, VIDEO3, VIDEO4, TAPE, CD

Multichannel Input

7.1 ch (DVD)

■Audio Outputs

Digital Output

Optical: 1

Analog Outputs

TAPE, VIDEO1, VIDEO2, ZONE2 L/R

Multichannel Pre

 

Outputs

7.1 ch

Speaker Outputs

L, R, C, SL, SR, SBL, SBR

 

ZONE2 (L, R)

Phones

1

RS232

1

IR Input/Output

2/1

12 V Trigger Out

A, B, C

Specifications and features are subject to change without notice.

87

Page 86 Page 88
Image 87
Page 86 Page 88
Contents DTR-5.6 Avis Important Safety InstructionsPower PrecautionsMake sure you have the following accessories Supplied AccessoriesContents Features Before Using the AV receiver Installing the BatteriesUsing the Remote Controller Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverIR in A/B and OUT Rear PanelComponent Video in 1, 2, XM antenna on North American modelThese terminal posts are for connecting speakers in Zone Video 1 IN/OUT and Video 2 IN/OUTFRONT, CENTER, SURROUND, Remote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Enjoying Home Theater Connecting Your SpeakersConnecting Your Speakers Connecting Your SpeakersSpeaker Connection Precautions Connecting the Speaker CablesStrip about 5/8 Attach the FM antenna, as shown American Model Connecting AntennaConnecting the AM Loop Antenna Connecting the Indoor FM AntennaUsing a TV/FM Antenna Splitter Connecting AntennaConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaAV Connection Color Coding Connecting Your ComponentsAbout AV Connections Optical Digital JacksVideo Connection Formats Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Which Connections Should I Use?Hint Connecting a TV or ProjectorVideo Connection Audio ConnectionConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Step Connecting a CD PlayerTurntable without a Built-in Phono Preamp Connecting a TurntableConnecting a Power Amplifier Connecting a Cassette, CDR, MiniDisc, or DAT RecorderAuto Power On/Standby Connecting ComponentsStandby indicator lights up Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Connecting the Power CordSmooth Operation in a Few Easy Steps Do the automatic speaker setup-this is essentialTurning On the AV Receiver Turning On and StandbyConnected TV Put the speaker setup microPhone in the listening position Turn on the AV receiverOn completion, the following menu appears First Time SetupDisconnect the speaker setup Press EnterChecking the Results Press the Receiver button, fol Component Video SetupLowed by the Setup button Press the Setup buttonButtons to select 2. Digital Digital Audio Input SetupSetup closes Use the Up and DownMinimum Speaker Impedance Changing the Input DisplayYou must specify the TV system used in your area TV Format Setup Not North American modelsAM Frequency Step Setup on some models Hardware Setup menu appearsBasic AV Receiver Operation Select a listening mode and enjoySee Using the Listening Modes on Playing Your AV ComponentsDisplaying AM/FM Radio Information Tuning into AM/FM Radio StationsListening to the Radio Listening to AM/FM StationsConnecting the XM Antenna Listening to the RadioSigning Up for XM Satellite Radio Use the Up and Down Buttons to select a channel Channel Search modeMode button, followed by Selecting XM Radio ChannelsNel Displaying XM Radio InformationSelecting XM Channels from the Front Panel Buttons to select a chanXM Radio Messages Positioning the XM AntennaXM Channels Presetting AM/FM StationsSelecting Presets Deleting PresetsInput Channel Using the Multichannel DVD InputUsing the Multichannel DVD Input Multichannel DVD Input SettingsMuting the AV Receiver Adjusting Speaker LevelsSetting the Display Brightness Common FunctionsDisplaying Source Information Using the Sleep TimerUsing Headphones Common FunctionsSelecting on the AV Receiver Using the Listening ModesSelecting with the Remote Controller Selecting the Listening ModesDVD Using the Listening ModesSound is output by the front left and right speakers Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS About the Listening ModesRecording Recording Audio and Video from Separate SourcesRecording the Input Source About the Onscreen Setup Menus Onscreen Setup MenusAdjusting the Listening Modes Audio Adjust MenuUsing the Cine Filter Function Neo6 Music Adjusting the Listening ModesTone Control Settings PL IIx and Neo6 Settings PL IIx Music 2 ch onlyMultiplex Dolby Digital SettingsMono/Multiplex Settings LFE Level SettingOptions for that input selector Appear Default Listening ModesListening Mode Preset menu Appears Use the Up and Down Buttons to select 5. ListeningSpeaker Config menu appears Advanced SetupSpeaker Setup Speaker Setup menu appearsCrossover Advanced SetupSubwoofer Mode Speaker DistanceSpeaker Distance menu appears Speaker is the same Repeat so that the volumeSpeaker Level Calibration Test tone from eachTings option to Equalizer SettingsRepeat steps 6 and 7 for each speaker Buttons to set the a. Use SetDelay Input SetupIntelliVolume Volume SetupPreferences OSD Position OSD Setup12V Trigger A/B/C Setup Lock SetupChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID Opt or coax, and then press Digital Input Signal FormatsButtons to select an input source That’s assigned to a digital inputZone Connecting ZoneUsing Another Amp in Zone Using Only Speakers in ZoneZone 2 Out Setting Powered Zone 2 SettingUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV Receiver Level+ buttons Zone 2 Remote Mode butTo adjust Ton, and then use the Level12V Trigger Setting for Each Input Source Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting DelayUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Controlling Other Components Entering Remote Control CodesControlling Other Components Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Resetting the Remote Mode ButtonsTV Input On, Standby, TVCH +/-, TV CH + Prev CHLearning Commands from Other Remote Controllers Deleting Macros Using MacrosMaking Macros Running MacrosTroubleshooting Troubleshooting Can’t control other components Remote controller doesn’t workCan’t learn commands from another remote controller Sound changes when I connect my head- phonesVideo Section SpecificationAmplifier Section General3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents