Integra DTR-5.6 instruction manual Using the 12V Triggers in Zone 2 and the Main Room, Delay

Page 77

DTR-5.6.book Page 77 Thursday, September 22, 2005 5:07 PM

Zone 2—Continued

Using the 12V Triggers in Zone 2 and the Main Room

When the AV receiver’s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V trigger input on a con- nected component, you can specify whether or not a 12- volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either.

Hookup

• Use a miniplug cable to connect the AV receiver’s 12 V TRIGGER OUT A, B, or C jack to the 12 V trig- ger input on the connected component.

1

Press the [Receiver] Remote

 

 

Mode button, followed by the

 

[Setup] button.

 

The main menu appears onscreen.

2

Use the Up and Down [ ]/[ ]

buttons to select “7. Preference,” and then press [Enter].

The Preference menu appears.

3 Use the Up and Down []/[ ] buttons to select “12V Trigger Setup” A, B, or C, and then press [Enter].

4 Use the Up and Down []/[ ] buttons to select “Delay” or an input source, and use the Left and Right []/[ ] buttons to change the setting.

Repeat this step as necessary for each setting.

5

Press the [Setup] button.

 

 

Setup closes.

■Delay

When several components are turned on simultaneously via the 12-volt triggers, depending on the type of compo- nents, a large amount of current may be drawn momen- tarily. To prevent this, you can delay the trigger signals output by the AV receiver. In addition, by delaying the trigger signal for your power amplifier so that it’s the last component to be turned on, you can avoid the “thump” noise that’s sometimes heard when a source component is turned on.

The delay setting determines how long after the input source is changed on the AV receiver the trigger signal is output. It can be set to 0 sec, 1 sec, 2 sec, or 3 sec. When set to 0 sec, the trigger signal is output as soon as the input source is changed.

■12V Trigger Setting for Each Input Source

By default, all input sources on the 12V Trigger A Setup menu are set to Main, those on the 12V Trigger B Setup menu are set to Main/Zone 2, and those on the 12V Trig- ger C Setup menu are set to Zone2.

Off: No trigger signal is output.

Main: Select this if you want to output a 12-volt trig- ger signal when a connected component is selected as the source for the main room.

Zone2: Select this if you want to output a 12-volt trig- ger signal when a connected component is selected as the source for Zone 2.

Main/Zone2: Select this if you want to output a 12-volt trigger signal when a connected component is selected as the source for either the main room or Zone 2.

77

Page 76 Page 78
Image 77
Page 76 Page 78
Contents DTR-5.6 Avis Important Safety InstructionsPower PrecautionsMake sure you have the following accessories Supplied AccessoriesContents Features Using the Remote Controller Before Using the AV receiverInstalling the Batteries Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverComponent Video in 1, 2, Rear PanelXM antenna on North American model IR in A/B and OUTFRONT, CENTER, SURROUND, These terminal posts are for connecting speakers in ZoneVideo 1 IN/OUT and Video 2 IN/OUT Receiver/Tape Mode Remote ControllerAbout the Remote Controller Modes Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Enjoying Home Theater Connecting Your SpeakersConnecting Your Speakers Connecting Your SpeakersStrip about 5/8 Speaker Connection PrecautionsConnecting the Speaker Cables Connecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor FM Antenna Connecting AntennaConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingConnecting Audio and Video Signals to the AV Receiver Connecting Your ComponentsWhich Connections Should I Use? Video Connection FormatsVideo Connection Connecting a TV or ProjectorAudio Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Step Connecting a CD PlayerTurntable without a Built-in Phono Preamp Connecting a TurntableConnecting a Power Amplifier Connecting a Cassette, CDR, MiniDisc, or DAT RecorderAuto Power On/Standby Connecting ComponentsConnecting the RS232 Port Connecting the Power Cords of Other ComponentsConnecting the Power Cord Standby indicator lights upTurning On the AV Receiver Do the automatic speaker setup-this is essentialTurning On and Standby Smooth Operation in a Few Easy StepsPhone in the listening position Put the speaker setup microTurn on the AV receiver Connected TVDisconnect the speaker setup First Time SetupPress Enter On completion, the following menu appearsChecking the Results Lowed by the Setup button Component Video SetupPress the Setup button Press the Receiver button, folSetup closes Digital Audio Input SetupUse the Up and Down Buttons to select 2. DigitalMinimum Speaker Impedance Changing the Input DisplayAM Frequency Step Setup on some models TV Format Setup Not North American modelsHardware Setup menu appears You must specify the TV system used in your areaSee Using the Listening Modes on Select a listening mode and enjoyPlaying Your AV Components Basic AV Receiver OperationListening to the Radio Tuning into AM/FM Radio StationsListening to AM/FM Stations Displaying AM/FM Radio InformationSigning Up for XM Satellite Radio Connecting the XM AntennaListening to the Radio Mode button, followed by Channel Search modeSelecting XM Radio Channels Use the Up and Down Buttons to select a channelSelecting XM Channels from the Front Panel Displaying XM Radio InformationButtons to select a chan NelXM Radio Messages Positioning the XM AntennaSelecting Presets Presetting AM/FM StationsDeleting Presets XM ChannelsUsing the Multichannel DVD Input Using the Multichannel DVD InputMultichannel DVD Input Settings Input ChannelSetting the Display Brightness Adjusting Speaker LevelsCommon Functions Muting the AV ReceiverUsing Headphones Using the Sleep TimerCommon Functions Displaying Source InformationSelecting with the Remote Controller Using the Listening ModesSelecting the Listening Modes Selecting on the AV ReceiverDVD Using the Listening ModesUse this mode with any stereo movie e.g., TV, DVD, VHS Use this mode with any stereo or TV, DVD, VHSAbout the Listening Modes Sound is output by the front left and right speakersRecording the Input Source RecordingRecording Audio and Video from Separate Sources About the Onscreen Setup Menus Onscreen Setup MenusUsing the Cine Filter Function Adjusting the Listening ModesAudio Adjust Menu Tone Control Settings Adjusting the Listening ModesPL IIx and Neo6 Settings PL IIx Music 2 ch only Neo6 MusicMono/Multiplex Settings Dolby Digital SettingsLFE Level Setting MultiplexListening Mode Preset menu Appears Default Listening ModesUse the Up and Down Buttons to select 5. Listening Options for that input selector AppearSpeaker Setup Advanced SetupSpeaker Setup menu appears Speaker Config menu appearsCrossover Advanced SetupSpeaker Distance menu appears Subwoofer ModeSpeaker Distance Speaker Level Calibration Repeat so that the volumeTest tone from each Speaker is the sameRepeat steps 6 and 7 for each speaker Equalizer SettingsButtons to set the a. Use Set Tings option toDelay Input SetupPreferences IntelliVolumeVolume Setup 12V Trigger A/B/C Setup OSD SetupLock Setup OSD PositionChanging the AV Receiver’s Remote ID Changing the Remote Controller’s IDRemote IDs Buttons to select an input source Digital Input Signal FormatsThat’s assigned to a digital input Opt or coax, and then pressUsing Another Amp in Zone Connecting ZoneUsing Only Speakers in Zone ZoneZone 2 Out Setting Powered Zone 2 SettingControlling Zone 2 from the AV Receiver Using ZoneControlling Zone 2 with the Remote Controller To adjust Zone 2 Remote Mode butTon, and then use the Level Level+ buttonsRepeat this step as necessary for each setting Using the 12V Triggers in Zone 2 and the Main RoomDelay 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with Other Components Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Zone Controlling Other Components Entering Remote Control CodesRemote Control Codes for Integra Components Connected via Resetting the Remote ControllerResetting the Remote Mode Buttons Controlling Other ComponentsCH +/-, TV CH + On, Standby, TVPrev CH TV InputLearning Commands from Other Remote Controllers Making Macros Using MacrosRunning Macros Deleting MacrosTroubleshooting Troubleshooting Can’t learn commands from another remote controller Remote controller doesn’t workSound changes when I connect my head- phones Can’t control other componentsAmplifier Section SpecificationGeneral Video Section3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents