Integra DTR-5.6 Speaker Level Calibration, Repeat so that the volume, Test tone from each

Page 66

DTR-5.6.book Page 66 Thursday, September 22, 2005 5:07 PM

Advanced Setup—Continued

6

Repeat step 5 for all speakers.

 

7

Press the [Setup] button.

 

 

Setup closes.

Note:

•This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button.

Speaker Level Calibration

These settings are set automatically by the Automatic Speaker Setup function (see page 37).

With these settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listening position.

Note:

• The speakers cannot be calibrated while the output of the AV receiver is muted or a pair of headphones is connected.

1

Press the [Receiver] Remote

 

 

Mode button, followed by the

 

[Setup] button.

 

The main menu appears onscreen.

2 Use the Up and Down []/[ ] buttons to select “3. Speaker Setup,” and then press [Enter]. The Speaker Setup menu appears.

3

Use the Up and Down [ ]/[ ]

 

buttons to select “Level Calibra-

 

tion,” and then press [Enter].

 

The Level Calibration menu appears

 

and the pink noise test tone is output by

 

the front left speaker.

 

 

3-4.Level Calibration

 

------------------------

 

a.Left

:

0dB

 

b.Center

:

0dB

 

c.Right

:

0dB

 

d.Surround R

:

0dB

 

e.SurrBack R

:

0dB

 

f.SurrBack L

:

0dB

 

g.Surround L

:

0dB

 

h.Subwoofer

:

0dB

 

Note:

 

Speakers that you set to No or None on

 

the Speaker Config menu (page 63)

 

cannot be adjusted.

 

 

4

Use the Up and Down [ ]/[ ]

buttons to select each speaker, and use the Left and Right

[]/[ ] buttons to set the vol- ume.

The level can be adjusted from –12 to +12 dB in 1 dB steps (–15 to +12 dB for the subwoofer).

5

Repeat step 4 so that the volume

 

 

of the test tone from each

 

speaker is the same.

 

If you’re using a handheld sound level

 

meter, adjust the level of each speaker

 

so it reads 75 dB SPL at the listening

 

position, measured with C-weighting

 

and slow reading.

 

 

6

Press the [Setup] button.

 

 

Setup closes.

Note:

•The speaker levels can also be changed by using the dedicated buttons on the remote controller. Press the [Test Tone] button to output the test tone. Use the [CH Sel] button to select each speaker, and use the [Level–] and [Level+] buttons to adjust the level.

66

Page 65 Page 67
Image 66
Page 65 Page 67
Contents DTR-5.6 Important Safety Instructions AvisPrecautions PowerSupplied Accessories Make sure you have the following accessoriesContents Features Before Using the AV receiver Installing the BatteriesUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayXM antenna on North American model Rear PanelComponent Video in 1, 2, IR in A/B and OUTThese terminal posts are for connecting speakers in Zone Video 1 IN/OUT and Video 2 IN/OUTFRONT, CENTER, SURROUND, Remote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersSpeaker Connection Precautions Connecting the Speaker CablesStrip about 5/8 Connecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor AM Antenna Connecting AntennaConnecting an Outdoor FM Antenna Using a TV/FM Antenna SplitterOptical Digital Jacks Connecting Your ComponentsAbout AV Connections AV Connection Color CodingWhich Connections Should I Use? Connecting Your ComponentsConnecting Audio and Video Signals to the AV Receiver Video Connection FormatsAudio Connection Connecting a TV or ProjectorVideo Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a CD Player StepConnecting a Turntable Turntable without a Built-in Phono PreampConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Power AmplifierConnecting Components Auto Power On/StandbyConnecting the Power Cord Connecting the Power Cords of Other ComponentsConnecting the RS232 Port Standby indicator lights upTurning On and Standby Do the automatic speaker setup-this is essentialTurning On the AV Receiver Smooth Operation in a Few Easy StepsTurn on the AV receiver Put the speaker setup microPhone in the listening position Connected TVPress Enter First Time SetupDisconnect the speaker setup On completion, the following menu appearsChecking the Results Press the Setup button Component Video SetupLowed by the Setup button Press the Receiver button, folUse the Up and Down Digital Audio Input SetupSetup closes Buttons to select 2. DigitalChanging the Input Display Minimum Speaker ImpedanceHardware Setup menu appears TV Format Setup Not North American modelsAM Frequency Step Setup on some models You must specify the TV system used in your areaPlaying Your AV Components Select a listening mode and enjoySee Using the Listening Modes on Basic AV Receiver OperationListening to AM/FM Stations Tuning into AM/FM Radio StationsListening to the Radio Displaying AM/FM Radio InformationConnecting the XM Antenna Listening to the RadioSigning Up for XM Satellite Radio Selecting XM Radio Channels Channel Search modeMode button, followed by Use the Up and Down Buttons to select a channelButtons to select a chan Displaying XM Radio InformationSelecting XM Channels from the Front Panel NelPositioning the XM Antenna XM Radio MessagesDeleting Presets Presetting AM/FM StationsSelecting Presets XM ChannelsMultichannel DVD Input Settings Using the Multichannel DVD InputUsing the Multichannel DVD Input Input ChannelCommon Functions Adjusting Speaker LevelsSetting the Display Brightness Muting the AV ReceiverCommon Functions Using the Sleep TimerUsing Headphones Displaying Source InformationSelecting the Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DVDAbout the Listening Modes Use this mode with any stereo or TV, DVD, VHSUse this mode with any stereo movie e.g., TV, DVD, VHS Sound is output by the front left and right speakersRecording Recording Audio and Video from Separate SourcesRecording the Input Source Onscreen Setup Menus About the Onscreen Setup MenusAdjusting the Listening Modes Audio Adjust MenuUsing the Cine Filter Function PL IIx and Neo6 Settings PL IIx Music 2 ch only Adjusting the Listening ModesTone Control Settings Neo6 MusicLFE Level Setting Dolby Digital SettingsMono/Multiplex Settings MultiplexUse the Up and Down Buttons to select 5. Listening Default Listening ModesListening Mode Preset menu Appears Options for that input selector AppearSpeaker Setup menu appears Advanced SetupSpeaker Setup Speaker Config menu appearsAdvanced Setup CrossoverSubwoofer Mode Speaker DistanceSpeaker Distance menu appears Test tone from each Repeat so that the volumeSpeaker Level Calibration Speaker is the sameButtons to set the a. Use Set Equalizer SettingsRepeat steps 6 and 7 for each speaker Tings option toInput Setup DelayIntelliVolume Volume SetupPreferences Lock Setup OSD Setup12V Trigger A/B/C Setup OSD PositionChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID That’s assigned to a digital input Digital Input Signal FormatsButtons to select an input source Opt or coax, and then pressUsing Only Speakers in Zone Connecting ZoneUsing Another Amp in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV Receiver Ton, and then use the Level Zone 2 Remote Mode butTo adjust Level+ buttonsDelay Using the 12V Triggers in Zone 2 and the Main RoomRepeat this step as necessary for each setting 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Mode Buttons Resetting the Remote ControllerRemote Control Codes for Integra Components Connected via Controlling Other ComponentsPrev CH On, Standby, TVCH +/-, TV CH + TV InputLearning Commands from Other Remote Controllers Running Macros Using MacrosMaking Macros Deleting MacrosTroubleshooting Troubleshooting Sound changes when I connect my head- phones Remote controller doesn’t workCan’t learn commands from another remote controller Can’t control other componentsGeneral SpecificationAmplifier Section Video Section3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents