Integra DTR-5.6 instruction manual Troubleshooting

Page 84

DTR-5.6.book Page 84 Thursday, September 22, 2005 5:07 PM

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased.

Power

Can’t turn on the AV receiver

Make sure that the power cord is plugged into the wall outlet properly.

Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.

The AV receiver turns off as soon as it’s turned on

The amp protection circuit has been activated. Remove the power cord from the wall outlet immedi- ately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord discon- nected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact the dealer from whom you purchased.

Audio

There’s no sound or it’s very quiet

Make sure that the digital input source is selected properly (page 41).

Make sure that all audio connecting plugs are pushed in all the way (page 22).

Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with metal part of each speaker terminal (page 19)

Make sure that the speaker cables are not shorting.

Check the volume (page 44). The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment.

If the MUTING indicator is shown on the display, press the remote controller’s [Muting] button to unmute the AV receiver (page 52).

While a pair of headphones is connected to the Phones jack, no sound is output by the speakers (page 53).

Check the digital audio output settings on the con- nected device. On some games consoles, such as those that can play DVDs, the default setting is off.

With some DVD-Video discs, you need to select an audio format from a menu.

If your turntable doesn’t have a built-in phono preamp, you must connect one between it and the AV receiver. If your turntable uses an MC cartridge, you must con- nect an MC head amp, or an MC transformer

(page 32).

Check the speaker settings (pages 63–67).

The input signal format is set to PCM or DTS. Set it to Auto (page 72).

84

Only the front speakers produce sound

When the Stereo listening mode is selected, only the front speakers and subwoofer produce sound.

In the Mono listening mode, only the front speakers output sound when the Output Sp setting is set to Front (page 61).

Make sure the speakers are configured correctly (pages 63, 65).

Only the center speaker produces sound

If you use the Pro Logic IIx Movie or Pro Logic IIx Music listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

In the Mono listening mode, only the center speaker outputs sound when the Output Sp setting is set to Center (page 61).

Make sure the speakers are configured correctly (pages 63, 65).

The surround speakers produce no sound

When the Stereo or Mono listening mode is selected, the surround speakers produce no sound.

Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.

Make sure the speakers are configured correctly (pages 63, 65).

The center speaker produces no sound

When the Stereo listening mode is selected, the center speaker produces no sound.

In the Mono listening mode, only the front speakers output sound when the Output Sp setting is set to Front (page 61).

Make sure the speakers are configured correctly (pages 63, 65).

The surround back speakers produce no sound

The surround back speakers are not used with all lis- tening modes. Select another listening mode

(page 54).

Not much sound may be produced by the surround back speakers with some sources.

Make sure the speakers are configured correctly (pages 63, 65).

When the ZONE 2 SPEAKERS terminals are used, playback in the main room is reduced to 5.1-channels, and the surround back speakers produce no sound (page 73).

The subwoofer produces no sound

When you play source material that contains no infor- mation in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly (pages 63, 65).

Image 84
Contents DTR-5.6 Important Safety Instructions AvisPrecautions PowerSupplied Accessories Make sure you have the following accessoriesContents Features Before Using the AV receiver Installing the BatteriesUsing the Remote Controller Getting to Know the AV Receiver Front PanelGetting to Know the AV Receiver DisplayRear Panel Component Video in 1, 2,XM antenna on North American model IR in A/B and OUTThese terminal posts are for connecting speakers in Zone Video 1 IN/OUT and Video 2 IN/OUTFRONT, CENTER, SURROUND, Remote Controller About the Remote Controller ModesReceiver/Tape Mode Remote Controller DVD Mode CD, MD, and CDR Modes HDD Mode Connecting Your Speakers Enjoying Home TheaterConnecting Your Speakers Connecting Your SpeakersSpeaker Connection Precautions Connecting the Speaker CablesStrip about 5/8 Connecting Antenna Connecting the AM Loop AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shown American ModelConnecting Antenna Connecting an Outdoor FM AntennaConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterConnecting Your Components About AV ConnectionsOptical Digital Jacks AV Connection Color CodingConnecting Your Components Connecting Audio and Video Signals to the AV ReceiverWhich Connections Should I Use? Video Connection FormatsConnecting a TV or Projector Video ConnectionAudio Connection HintConnecting a DVD player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Connecting a CD Player StepConnecting a Turntable Turntable without a Built-in Phono PreampConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Power AmplifierConnecting Components Auto Power On/StandbyConnecting the Power Cords of Other Components Connecting the RS232 PortConnecting the Power Cord Standby indicator lights upDo the automatic speaker setup-this is essential Turning On the AV ReceiverTurning On and Standby Smooth Operation in a Few Easy StepsPut the speaker setup micro Phone in the listening positionTurn on the AV receiver Connected TVFirst Time Setup Disconnect the speaker setupPress Enter On completion, the following menu appearsChecking the Results Component Video Setup Lowed by the Setup buttonPress the Setup button Press the Receiver button, folDigital Audio Input Setup Setup closesUse the Up and Down Buttons to select 2. DigitalChanging the Input Display Minimum Speaker ImpedanceTV Format Setup Not North American models AM Frequency Step Setup on some modelsHardware Setup menu appears You must specify the TV system used in your areaSelect a listening mode and enjoy See Using the Listening Modes onPlaying Your AV Components Basic AV Receiver OperationTuning into AM/FM Radio Stations Listening to the RadioListening to AM/FM Stations Displaying AM/FM Radio InformationConnecting the XM Antenna Listening to the RadioSigning Up for XM Satellite Radio Channel Search mode Mode button, followed bySelecting XM Radio Channels Use the Up and Down Buttons to select a channelDisplaying XM Radio Information Selecting XM Channels from the Front PanelButtons to select a chan NelPositioning the XM Antenna XM Radio MessagesPresetting AM/FM Stations Selecting PresetsDeleting Presets XM ChannelsUsing the Multichannel DVD Input Using the Multichannel DVD InputMultichannel DVD Input Settings Input ChannelAdjusting Speaker Levels Setting the Display BrightnessCommon Functions Muting the AV ReceiverUsing the Sleep Timer Using HeadphonesCommon Functions Displaying Source InformationUsing the Listening Modes Selecting with the Remote ControllerSelecting the Listening Modes Selecting on the AV ReceiverUsing the Listening Modes DVDUse this mode with any stereo or TV, DVD, VHS Use this mode with any stereo movie e.g., TV, DVD, VHSAbout the Listening Modes Sound is output by the front left and right speakersRecording Recording Audio and Video from Separate SourcesRecording the Input Source Onscreen Setup Menus About the Onscreen Setup MenusAdjusting the Listening Modes Audio Adjust MenuUsing the Cine Filter Function Adjusting the Listening Modes Tone Control SettingsPL IIx and Neo6 Settings PL IIx Music 2 ch only Neo6 MusicDolby Digital Settings Mono/Multiplex SettingsLFE Level Setting MultiplexDefault Listening Modes Listening Mode Preset menu AppearsUse the Up and Down Buttons to select 5. Listening Options for that input selector AppearAdvanced Setup Speaker SetupSpeaker Setup menu appears Speaker Config menu appearsAdvanced Setup CrossoverSubwoofer Mode Speaker DistanceSpeaker Distance menu appears Repeat so that the volume Speaker Level CalibrationTest tone from each Speaker is the sameEqualizer Settings Repeat steps 6 and 7 for each speakerButtons to set the a. Use Set Tings option toInput Setup DelayIntelliVolume Volume SetupPreferences OSD Setup 12V Trigger A/B/C SetupLock Setup OSD PositionChanging the Remote Controller’s ID Remote IDsChanging the AV Receiver’s Remote ID Digital Input Signal Formats Buttons to select an input sourceThat’s assigned to a digital input Opt or coax, and then pressConnecting Zone Using Another Amp in ZoneUsing Only Speakers in Zone ZonePowered Zone 2 Setting Zone 2 Out SettingUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV Receiver Zone 2 Remote Mode but To adjustTon, and then use the Level Level+ buttonsUsing the 12V Triggers in Zone 2 and the Main Room Repeat this step as necessary for each settingDelay 12V Trigger Setting for Each Input SourceUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneUsing a Multiroom Kit with Other Components Entering Remote Control Codes Controlling Other ComponentsResetting the Remote Controller Remote Control Codes for Integra Components Connected viaResetting the Remote Mode Buttons Controlling Other ComponentsOn, Standby, TV CH +/-, TV CH +Prev CH TV InputLearning Commands from Other Remote Controllers Using Macros Making MacrosRunning Macros Deleting MacrosTroubleshooting Troubleshooting Remote controller doesn’t work Can’t learn commands from another remote controllerSound changes when I connect my head- phones Can’t control other componentsSpecification Amplifier SectionGeneral Video Section3 4 4 1 0

DTR-5.6 specifications

The Integra DTR-5.6 is a high-performance AV receiver that exemplifies the blend of cutting-edge technology and audiophile-grade quality. With a focus on delivering stellar sound performance and versatility, the DTR-5.6 achieves this through a combination of features that enhance both convenience and audio fidelity.

One of the standout features of the DTR-5.6 is its multichannel audio processing capability. Supporting Dolby TrueHD and DTS-HD Master Audio, this receiver can decode high-resolution audio formats that are standard in modern home theater systems. This ensures that users experience soundtracks as intended by their creators, with immersive clarity and depth. Additionally, it incorporates Audyssey MultEQ XT, a sophisticated room calibration technology. This feature analyzes the acoustics of your listening environment, automatically adjusting speaker settings to optimize sound quality based on the specific audio landscape of your room.

Connectivity is another strong point of the Integra DTR-5.6. It provides multiple HDMI inputs, supporting 1080p and 4K video pass-through. This allows users to connect various high-definition devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. The receiver also features built-in Wi-Fi and Ethernet connections, enabling seamless access to streaming services and internet radio. With support for services like Spotify, Pandora, and others, users can easily enjoy their favorite music without needing additional equipment.

The DTR-5.6 is designed with a robust multi-zone capability, allowing users to enjoy different audio content in different rooms simultaneously. This feature provides flexibility and convenience for larger homes. For audiophiles, the receiver is also equipped with high-current amplifiers that ensure dynamic sound reproduction and sufficient power output for driving demanding speakers.

For user convenience, the Integra DTR-5.6 comes with an intuitive on-screen interface and an easy-to-use remote control. The receiver’s sleek design and user-friendly layout make it a great addition to any entertainment setup. Furthermore, it supports various streaming protocols, including Apple AirPlay and Miracast, enhancing its versatility for modern multimedia needs.

In sum, the Integra DTR-5.6 is a powerhouse of an AV receiver, boasting advanced audio processing technologies, versatile connectivity options, and smart features that cater to both casual listeners and serious audiophiles alike. Its combination of performance, flexibility, and ease of use makes it an excellent choice for anyone looking to elevate their home entertainment experience.