Yeoman YM-CL8HB manual Lift bars to remove, Remove Rear Bar see Diagram, Unscrew the boss

Page 25

INSTALLATION INSTRUCTIONS

7

Lift bars to remove

PR8867

—Remove Rear Bar (see Diagram 8).

8

PR8868

To remove the Riddling Boss:

—Use the 5mm hex key as shown in Diagram 9.

9

 

 

5mm

Fixing

Hex Key

 

Bolt

 

Riddling

 

Boss

PR8870

 

—Unscrew the boss.

 

—Remove Riddling Cam Bar (see Diagram 10).

 

10

PR8875

To remove Multi-fuel frames:

—Lift frames from the front.

—Remove right hand side first through the front of the stove.

—Repeat for the left hand side.

11

PR8876

—Replace in reverse order.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents YM-CL8HB Yeoman CLContents Installation Engineer Appliance Commissioning ChecklistRetailer appliance was purchased from Essential Information Must be completedGeneral Points User InstructionsSerial Number ThermostatDo not place tool on hot surfaces e.g. top of stove Heating System controlsUse a protected gloved hand to operate Condensation Using the Appliance for the First TimeNormal Running Seasonal USESolid fuel Lighting the ApplianceBurning wood Running The applianceDo not load above the log guard or base of baffle Thermostat Operation RefuellingBurning tips ASH Removal Extended burning Wood burning trayOVER-FIRING Over-firing can cause permanent damage to the applianceCleaning Glass General CleaningChimney fire Chimney SweepingCare of stove Seasonal use Troubleshooting tipsOpen up the airwash to make All or some of the radiators do not get hotStandard Features TECHNICAL SPECIFICATIONBoiler Output Chart YeomanAll dimensions are in mm 25.4mm = Yeoman DimensionsCast Top Plate Incl. feet @ 6mm on underside 563 572 363 105 478 153/6 449 441 225 430 224 317Flue or Chimney Site RequirementsMax. Draught = 2.0mm Wg Min. Draught = 1.0mm Wg U.K Flue PlateFlue Outlet Positions Hearth DimensionsRequirement for the walls Walls Next to a Hearth80mm Flue PRE-INSTALLATION ChecksWithout Liner System 150 Flue / Chimney SizeModel VentilationMm² 4400 Additional Ventilation Changes to Document J, England & Wales, from 01/10/2010Installing the Appliance Installation InstructionsTop flue pipe installation Legal requirementsRear flue pipe installation Secure with self tapping screw Seal the connecting jointsDo not use a 90˚elbow to make this connection To chimney connection as detailed in building regulationsRemoval of Riddling Mechanism Fitting and Removal of the BaffleEnsure baffle sits On front supports Baffle In Place Do not modify the baffleLift bars to remove Remove Rear Bar see DiagramUnscrew the boss Replace in reverse orderCast TOP Hearth FixingFixing holes Hearth mounts Top Flue Rear FlueCentral Heating System Pump Pipe work DiagramsElectrical Supply Conventional Pipe work systemsFeed Expansion Cistern Controls General Link UP SystemsCommissioning CommissioningInstructions for Use Give the copy of the Instructions to the customerAnnual Service Fitting and Removal of Baffle Removal of the LOG GuardFitting a NEW Door Glass Do not use appliance without the log guard in positionDo not over tighten the clamp as this could break the glass Fitting a new door sealMid door Rope seal E Joint To adjust the door hinge plate assembly Adjusting Door Catch & HingesHetas Approved Chimney Sweeps Spare Parts List Cast Door Service Records
Top Page Image Contents