Yeoman YM-CL8HB manual Refuelling, Thermostat Operation, Burning tips

Page 9

USER INSTRUCTIONS

5.8De-ash the firebed before re-fuelling (see User Instructions, Section 7).

Open the Primary Air Control fully to establish a glowing bed before adding new fuel.

Burn new fuel at a high temperature (see Diagram 7) for a few minutes before adjusting the Primary Air Control to the desired setting.

Refuel little and often for clean, efficient burning.

5.9Experience establishes settings to suit personal preference.

5.10Do not burn large amounts of fuel with the Primary Air Control on a low combustion setting for long periods of time. This reduces the glass cleaning effect of the Airwash and causes tars and creosotes to build-up in the appliance and flue system.

5.11When in use, burning the appliance at a high temperature for a short period reduces tars and creosotes.

5.12Only anthracite or smokeless fuels suitable for use in closed appliances must be burned in this appliance.

5.13Do not burn bituminous coal, ‘petro-coke’ or other petroleum based fuels as this invalidates the product guarantee.

5.14Do not load fuel above the log guard and the base of the baffle at the back of the firebox (see Diagram 5).

REFUELLING

5.15De-ash the fire bed before refuelling, see Ash Removal

Open the Primary air control fully to establish a glowing bed before adding new fuel.

Do not refuel when a large amount of flame is present in the firebox as this could cause smoke or flames to spill into the room.

Close the doors immediately after refuelling.

Burn new fuel at a high temperature for a few minutes before adjusting the Primary air control to the desired setting.

Refuel little and often for clean, efficient burning.

5.16Do not re-fuel the stove above the level of the log guard or the base of the baffle.

THERMOSTAT OPERATION

5.17This appliance can be fitted with a thermostat kit to control the temperature of the boiler. See the instructions included in the kit for operation details.

6.Burning tips

6.1Fuel Quality (Wood)

Use wood with a moisture content of less than 20%. Seasoned logs have the bark beginning to lift and peel away and cracks radiating from the centre. They feel lighter than fresh cut wood of a similar size and sound hollow when struck against each other. Logs should not feel damp or have moss and fungal growths.

Symptoms related to wet wood:

Difficulty starting and keeping a fire burning well.

Smoke and small flames.

Dirty glass.

Rapid creosote build-up in the chimney.

Low heat output.

Short burn times, excessive fuel consumption and blue/grey smoke from the chimney.

Burn at a high temperature for a short period each day to avoid large build-ups of tars and creosote within the appliance and the flue system.

Use Stovax Protector chimney cleaner to reduce this problem.

6.2Fuel Quality (Solid Fuel)

Use recommended solid fuels approved for use with closed appliances.

Symptoms related to unsuitable fuels include:

Difficulty starting and keeping a fire burning well.

Smoke and small flames.

Dirty glass and/or fire bricks.

Short life span for Grate and Baffle.

Permanent staining of glass.

6.3Air inlets puffing smoke

Combustion gases can build up in the firebox and ignite as small explosions, causing smoke to puff out of the air inlets and other openings. This occurs if the air controls are shut soon after adding new fuel to a very hot fire. Stop by opening the air controls to increase combustion air and burning rate.

6.4Flue Draught

The chimney has two main functions:

1)To safely remove the smoke, gases and fumes from the house.

2)To provide a sufficient amount of draught (suction) in the appliance ensuring the fire keeps burning.

In the U.K.

*Registered on the Competent Persons Scheme (GB only) see page 35 / INFO (Republic of Ireland).

**This should be done by a HETAS registered chimney sweep, see page 35, who will issue you with a certificate.

9

Image 9
Contents YM-CL8HB Yeoman CLContents Installation Engineer Appliance Commissioning ChecklistRetailer appliance was purchased from Essential Information Must be completedGeneral Points User InstructionsSerial Number ThermostatHeating System controls Do not place tool on hot surfaces e.g. top of stoveUse a protected gloved hand to operate Condensation Using the Appliance for the First TimeNormal Running Seasonal USESolid fuel Lighting the ApplianceRunning The appliance Burning woodDo not load above the log guard or base of baffle Refuelling Thermostat OperationBurning tips ASH Removal Extended burning Wood burning trayOVER-FIRING Over-firing can cause permanent damage to the applianceCleaning Glass General CleaningChimney fire Chimney SweepingCare of stove Seasonal use Troubleshooting tipsOpen up the airwash to make All or some of the radiators do not get hotStandard Features TECHNICAL SPECIFICATIONBoiler Output Chart YeomanAll dimensions are in mm 25.4mm = Yeoman DimensionsCast Top Plate Incl. feet @ 6mm on underside 563 572 363 105 478 153/6 449 441 225 430 224 317Flue or Chimney Site RequirementsMax. Draught = 2.0mm Wg Min. Draught = 1.0mm Wg U.K Flue PlateFlue Outlet Positions Hearth DimensionsWalls Next to a Hearth Requirement for the walls80mm Flue PRE-INSTALLATION ChecksWithout Liner System 150 Flue / Chimney SizeModel VentilationMm² 4400 Additional Ventilation Changes to Document J, England & Wales, from 01/10/2010Installing the Appliance Installation InstructionsTop flue pipe installation Legal requirementsRear flue pipe installation Secure with self tapping screw Seal the connecting jointsDo not use a 90˚elbow to make this connection To chimney connection as detailed in building regulationsRemoval of Riddling Mechanism Fitting and Removal of the BaffleEnsure baffle sits On front supports Baffle In Place Do not modify the baffleLift bars to remove Remove Rear Bar see DiagramUnscrew the boss Replace in reverse orderCast TOP Hearth FixingFixing holes Hearth mounts Top Flue Rear FlueCentral Heating System Pump Pipe work DiagramsElectrical Supply Conventional Pipe work systemsFeed Expansion Cistern Controls General Link UP SystemsCommissioning CommissioningInstructions for Use Give the copy of the Instructions to the customerAnnual Service Fitting and Removal of Baffle Removal of the LOG GuardFitting a NEW Door Glass Do not use appliance without the log guard in positionFitting a new door seal Do not over tighten the clamp as this could break the glassMid door Rope seal E Joint Adjusting Door Catch & Hinges To adjust the door hinge plate assemblyHetas Approved Chimney Sweeps Spare Parts List Cast Door Service Records