Yeoman YM-CL8HB manual Adjusting Door Catch & Hinges, To adjust the door hinge plate assembly

Page 35

MAINTENANCE and SERVICING

7.ADJUSTING DOOR CATCH & HINGES

7.1To maintain the safe use of your appliance, you may need to adjust the door hinges to ensure the door closes safely and correctly.

7.2To adjust the door catch:

—Open the door to gain access to the catch.

—Use a 13mm A/F spanner to loosen the half lock nuts either side of the appliance body. This will allow the dome catch to rotate in and out (see diagram below).

Stove body

Washer

Half lock nuts

Dome catch

PR8740

—Once the desired setting has been achieved ensure the lock nuts are tightened against the appliance body.

7.3To adjust the door hinge plate assembly:

—Open door and lift free of hinge plate.

—Lay the door face down on a soft, flat surface, to protect the paintwork and glass.

—Use an M6 hexagon key to loosen the 4 x M6 screws.

M6 screws

x 4

PR8741

The hinge plate assembly is slotted so it can be moved up, down and sideways by approximately 3mm to adjust the position of the door in relation to the appliance.

—Once the desired position has been achieved ensure the screws are firmly tightened against the hinge plate assembly to maintain the position.

Organisations authorised to certify competence in the installation of domestic solid fuel appliances (Competent Persons Scheme):

APHC - Association of Plumbing and Heating

Contractors (Certification) Ltd.

www.aphc.co.uk

BESCA - Building Engineering Services Competence Accreditation Ltd.

www.besca.org.uk

HETAS - Heating Equipment Testing and Approval Scheme Ltd.

www.hetas.co.uk

NAPIT - National Association of Professional Inspectors and Testers Ltd.

www.napit.org.uk

NICEIC - NICEIC Group Ltd.

www.niceic.org.uk

HETAS Approved Chimney Sweeps:

Nacs - The National Association of Chimney Sweeps www.chimneyworks.co.uk

APICS - The Association of Master Chimney Sweeps Ltd. www.apics.org

The Guild of Master Chimney Sweeps guildofmasterchimneysweeps.co.uk

35

Image 35

Contents YM-CL8HB Yeoman CLContents Essential Information Must be completed Appliance Commissioning ChecklistInstallation Engineer Retailer appliance was purchased fromThermostat User InstructionsGeneral Points Serial NumberUse a protected gloved hand to operate Heating System controlsDo not place tool on hot surfaces e.g. top of stove Seasonal USE Using the Appliance for the First TimeCondensation Normal RunningSolid fuel Lighting the ApplianceDo not load above the log guard or base of baffle Running The applianceBurning wood Burning tips RefuellingThermostat Operation ASH Removal Over-firing can cause permanent damage to the appliance Wood burning trayExtended burning OVER-FIRINGChimney Sweeping General CleaningCleaning Glass Chimney fireCare of stove Seasonal use Troubleshooting tipsOpen up the airwash to make All or some of the radiators do not get hotYeoman TECHNICAL SPECIFICATIONStandard Features Boiler Output Chart563 572 363 105 478 153/6 449 441 225 430 224 317 Yeoman DimensionsAll dimensions are in mm 25.4mm = Cast Top Plate Incl. feet @ 6mm on undersideFlue Plate Site RequirementsFlue or Chimney Max. Draught = 2.0mm Wg Min. Draught = 1.0mm Wg U.KFlue Outlet Positions Hearth Dimensions80mm Walls Next to a HearthRequirement for the walls Flue / Chimney Size PRE-INSTALLATION ChecksFlue Without Liner System 150Changes to Document J, England & Wales, from 01/10/2010 VentilationModel Mm² 4400 Additional VentilationLegal requirements Installation InstructionsInstalling the Appliance Top flue pipe installationTo chimney connection as detailed in building regulations Secure with self tapping screw Seal the connecting jointsRear flue pipe installation Do not use a 90˚elbow to make this connectionDo not modify the baffle Fitting and Removal of the BaffleRemoval of Riddling Mechanism Ensure baffle sits On front supports Baffle In PlaceReplace in reverse order Remove Rear Bar see DiagramLift bars to remove Unscrew the bossTop Flue Rear Flue Hearth FixingCast TOP Fixing holes Hearth mountsCentral Heating System Conventional Pipe work systems Pipe work DiagramsPump Electrical SupplyFeed Expansion Cistern Controls General Link UP SystemsGive the copy of the Instructions to the customer CommissioningCommissioning Instructions for UseAnnual Service Do not use appliance without the log guard in position Removal of the LOG GuardFitting and Removal of Baffle Fitting a NEW Door GlassMid door Rope seal E Joint Fitting a new door sealDo not over tighten the clamp as this could break the glass Hetas Approved Chimney Sweeps Adjusting Door Catch & HingesTo adjust the door hinge plate assembly Spare Parts List Cast Door Service Records