ION DSP-AX750SE, RX-V750 Speaker connections, Connecting to Presence speaker terminals, 10 mm

Page 15

Speaker connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

•If you will use 6 ohm speakers, be sure to set this unit’s speaker impedance setting to 6 ohms before using (see page 24).

•Before connecting the speakers, make sure that the power of this unit is off.

•Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

•Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor.

A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red) terminals on this unit and your speaker. Connect the plain cable to the “–” (black) terminals.

10 mm

1

2

1Remove approximately 10 mm of insulation from the end of each speaker cable.

2Twist the exposed wires of the cable together to prevent short circuits.

3Unscrew the knob.

SPEAKER SETUP

5 Tighten the knob to secure the wire.

3

4

5

Red: positive (+)

Black: negative (–)

■Connecting to PRESENCE speaker terminals

2 1 3

1Open the tab.

2Insert one bare wire into the hole of each terminal.

3Return the tab to secure the wire.

PREPARATION

4Insert one bare wire into the hole in the side of each terminal.

English

13

Image 15

Contents DSP-AX750SE AV Amplifier Special Instructions for U.K. Model For U.K. customersContents Other features FeaturesBuilt-in 7-channel power amplifier Sound field featuresPlease check that you received all of the following parts Supplied accessoriesInstalling batteries in the remote control Getting StartedFront panel Controls and FunctionsFM/AM RX-V750 RX-V750 Europe model onlyVideo AUX jacks Phones Silent Cinema jackRemote control RDS tuning buttons Select k/nVOL -/+ Handling the remote control Using the remote controlFront panel display Input channel indicators Optimizer indicator96/24 indicator LFE indicatorRear panel Speaker placement Speaker Setup10 mm Connecting to Presence speaker terminalsTighten the knob to secure the wire Speaker connectionsRight Left Surround back Speakers Front speakers a Subwoofer System Presence speakersRight Left RX-V750 Right Left FrontSUB Woofer jack Front terminalsCenter terminals Surround terminalsDigital jacks ConnectionsCable indications Analog jacksMonitor Connecting video componentsConnections for DVD playback DVD playerConnecting to the Multi CH Input jacks For 6-channel input RX-V750For 8-channel input RX-V750 Connections for other video components Video AUX jacks on the front panelUse these jacks to connect any video source, such as a Connections for audio components Connecting audio componentsConnecting a turntable Connecting a tunerConnecting to an external amplifier Ground GND terminal Connecting the AM loop antennaFrequency Step switch Asia and General models only Indoor FM antenna Included AM loop antenna includedConnecting the power supply cord Connecting the AC power cordMemory back-up Impedance Selector switch Impedance Selector switchFront panel Turning on the powerTurn on the video monitor connected to this unit RX-V750 U.S.A. modelOptimizer microphone position Auto SetupOptimizer microphone setup IntroductionStarting the setup ResultwiringAutomenu Resultexit ErrorError E-5 If an error screen appearsPress u / d to select Result LIST, then press Select When you are finished, press SelectResultwiring screen appears If a warning screen appearsTroubleshooting for auto setup procedure Before auto setupErrors during auto setup Start playback or select a broadcast station Adjust the volume to the desired output levelPlayback Select the input sourceSelect a sound field program if desired To listen with headphones Silent CinemaTo adjust the tone Press Mute on the remote control Mute indicator blinksFront panel operation Selecting sound field programsMulti CH Input Selecting Multi CH InputPLIIxMusic Remote control operationEnjoying multi-channel software Decoders select with jPRO Logic SUR. Enhanced Press q/DTS on the remote control to select the decoderEnjoying 2-channel software PRO Logic SUR. StandardPress Pure Direct to activate pure direct To cancel, press Pure Direct againListening to high fidelity stereo sound Night listening modesDownmixing to 2 channels Listening to unprocessed input signalsSelecting input modes StraightPress u / d to display the following Information about the input signalDisplaying information about the input SourceTuning RX-V750 Automatic and manual tuningAutomatic tuning Press FM/AM to select the FM band Presetting stationsManual tuning Automatically presetting FM stationsManually presetting stations Automatic preset tuning optionsPress A/B/C/D/E to select the preset station group Selecting preset stationsWhen performing this operation with the remote Control, first press Tuner to set the remote to tuner modeSee Selecting preset stations Press PRESET/TUNING Edit againCT Clock Time mode PS Program Service name modePTY Program Type mode RT Radio Text modePTY Seek function To cancel this functionPress PTY Seek Mode to set this unit PTY Seek modeEON function Recording Special considerations when recording DTS softwareFor movie/video sources Sound Field Program DescriptionsSUR. Standard Dolby DigitalSUR. Standard Dolby Digital SUR. EnhancedSUR. Standard PRO Logic PRO LogicRock Concert For music sourcesConcert Hall Jazz ClubP08 Movie Theater Selecting the OSD mode Using the sleep timerSetting the sleep timer Advanced OperationsSleep OFF Canceling the sleep timerPress j / i to adjust the speaker output level Press Select when you have completed your adjustmentUsing the test tone Outputting the test tone from the Presence speakersPress AMP Press Test SET Menu To exit, press SET Menu when finished Using SET MenuPress u / d to select Manual Setup Press Select to enter Manual SetupSurr L/R SP Sound Menu 1/2Center SP Front SPCross Over Surr B L/R SPPresence SP LFE/BASS OUT02ASUBWOOFER Phase CSP DistanceSpeaker distance CSP Distance Gaudio SET Dcenter GEQElfe Level Fdynamic RangeOptical OUT HPR/SB SelectInput Menu CMPNT-V InputFor Coaxial Input jacks 5 Binput ModeCoaxial Cinput RenameOption MENU1/2 Adisplay SETBmemory Guard Speaker B set SP B CPARAM. INIDzone SET Parameter initialization CPARAM. INIControlling this unit Remote Control FeaturesControl area Advd DVDManufacturer Setting manufacturer codesPress Learn again to exit from the setup mode MD/CD Controlling other componentsLearn is displayed Programming codes from other remote controlsPress Learn using a ballpoint pen or similar object Press an input selector button to select a source componentChanging source names in the display window Clearing function sets Press Clear by using a ballpoint pen or similar objectPress u / d to select the clear mode Press Clear to exit from the clearing modeClearing individual functions Clearing a learned functionSelected component name appears in the display window What is a sound field Changing parameter settings Editing Sound Field ParametersElements of a sound field Press u / d to select the parameters Resetting parameters to the factory presetsTo reset a certain parameter To reset all parametersINIT. DLY Initial delay Sound Field Parameter DescriptionsRoom SIZE/P. Room Size Room size Liveness Surround liveness INIT. DLY Surround initial delaySB INIT. DLY Surround back initial delay Room Size Surround room sizeREV.DELAY Reverberation delay REV.TIME Reverberation timeREV. Level Reverberation level For DTS Neo6 Music Image Center image DIALG.LIFT Dialog liftFor 7ch Stereo CT Width Center widthGeneral TroubleshootingOne side can be Sound suddenlyGoes off Only the speaker onDolby Digital or DTS Or DTS indicator onVolume level is Record Volume levelTuner RX-V750 Does not learn new Remote controlDoes not work nor Function properlyPress Straight Effect to select the desired setting Resetting the Factory PresetsBe sure this unit is in standby mode Factory Preset appears in the front panel displayAudio formats GlossaryPCM Linear PCM Sound field programsAudio information LFE 0.1 channelVideo signal Video signal informationComponent video signal Composite video signalAudio Section SpecificationsWC85520