ION RX-V750 Auto Setup, Introduction, Optimizer microphone setup, Optimizer microphone position

Page 28

AUTO SETUP

Introduction

This receiver employs YAMAHA Parametric Room Acoustic Optimizer (YPAO) technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments. The supplied optimizer microphone collects and analyzes the sound your speakers produce in your actual listening environment.

Notes

Please be advised that it is normal for loud test tones to be output during the auto setup procedure.

If auto setup stops and error messages appear on the screen, follow the troubleshooting on page 30.

YPAO performs the following checks and makes appropriate adjustments to give you the best possible sound from your system.

WIRING/LEVEL:

Checks which speakers are connected and the polarity of each speaker. Also checks and adjusts the sound level (volume) of each speaker so that the sound level of each speaker is the same when heard from the listening position.

DISTANCE/PHASE:

Checks the distance of each speaker from the listening position and adjusts the delay of each channel so that the sound from each speaker reaches the listening position at the same time. Also checks the phase of each speaker.

SIZE:

Checks the speakers frequency response and sets the crossover/high cut frequency for the subwoofer to improve the sound relationship between the speakers and the subwoofer.

Optimizer microphone setup

1Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel.

(RX-V750 U.S.A. model)

 

OPTIMIZER

 

 

 

 

 

 

MIC

PRESET/TUNING FM/AM

A/B/C/D/E

l PRESET/TUNING h

MEMORY

TU

 

 

EDIT

NEXT

LEVEL

MAN'L/AUTO FM

A

 

 

PROGRAM

 

 

INPUT

 

PHONES

 

 

 

 

 

 

SPEAKERS

STRAIGHT

TONE CONTROL

INPUT MODE

 

 

A

B

 

 

 

 

 

Y

EFFECT

SILENT CINEMA

Notes

After you have completed the auto setup procedure, be sure to disconnect the optimizer microphone.

The optimizer microphone is sensitive to heat.

Keep it away from direct sunlight.

Do not place it on top of this unit.

2Place the optimizer microphone on a flat level surface with the omni-directional microphone head upward, at your normal listening position.

If possible, use a tripod (etc.) to affix the optimizer mic at the same height as your ears would be when you are seated in your listening position.

Optimizer microphone position

26

Image 28
Contents DSP-AX750SE AV Amplifier For U.K. customers Special Instructions for U.K. ModelContents Features Built-in 7-channel power amplifierSound field features Other featuresSupplied accessories Installing batteries in the remote controlGetting Started Please check that you received all of the following partsControls and Functions Front panelRX-V750 Europe model only Video AUX jacksPhones Silent Cinema jack FM/AM RX-V750Remote control Select k/n RDS tuning buttonsVOL -/+ Using the remote control Handling the remote controlFront panel display Optimizer indicator 96/24 indicatorLFE indicator Input channel indicatorsRear panel Speaker Setup Speaker placementConnecting to Presence speaker terminals Tighten the knob to secure the wireSpeaker connections 10 mmSubwoofer System Presence speakers Right LeftRX-V750 Right Left Front Right Left Surround back Speakers Front speakers aFront terminals Center terminalsSurround terminals SUB Woofer jackConnections Cable indicationsAnalog jacks Digital jacksConnecting video components Connections for DVD playbackDVD player MonitorFor 6-channel input RX-V750 Connecting to the Multi CH Input jacksFor 8-channel input RX-V750 Video AUX jacks on the front panel Connections for other video componentsUse these jacks to connect any video source, such as a Connecting audio components Connecting a turntableConnecting a tuner Connections for audio componentsConnecting to an external amplifier Connecting the AM loop antenna Frequency Step switch Asia and General models onlyIndoor FM antenna Included AM loop antenna included Ground GND terminalConnecting the AC power cord Connecting the power supply cordMemory back-up Impedance Selector switch Impedance Selector switchTurning on the power Turn on the video monitor connected to this unitRX-V750 U.S.A. model Front panelAuto Setup Optimizer microphone setupIntroduction Optimizer microphone positionResultwiring Starting the setupAutomenu Error Error E-5If an error screen appears ResultexitWhen you are finished, press Select Resultwiring screen appearsIf a warning screen appears Press u / d to select Result LIST, then press SelectBefore auto setup Troubleshooting for auto setup procedureErrors during auto setup Adjust the volume to the desired output level PlaybackSelect the input source Start playback or select a broadcast stationTo listen with headphones Silent Cinema To adjust the tonePress Mute on the remote control Mute indicator blinks Select a sound field program if desiredSelecting sound field programs Multi CH InputSelecting Multi CH Input Front panel operationRemote control operation Enjoying multi-channel softwareDecoders select with j PLIIxMusicPress q/DTS on the remote control to select the decoder Enjoying 2-channel softwarePRO Logic SUR. Standard PRO Logic SUR. EnhancedTo cancel, press Pure Direct again Listening to high fidelity stereo soundNight listening modes Press Pure Direct to activate pure directListening to unprocessed input signals Selecting input modesStraight Downmixing to 2 channelsInformation about the input signal Displaying information about the inputSource Press u / d to display the followingAutomatic and manual tuning Tuning RX-V750Automatic tuning Presetting stations Manual tuningAutomatically presetting FM stations Press FM/AM to select the FM bandAutomatic preset tuning options Manually presetting stationsSelecting preset stations When performing this operation with the remoteControl, first press Tuner to set the remote to tuner mode Press A/B/C/D/E to select the preset station groupPress PRESET/TUNING Edit again See Selecting preset stationsPS Program Service name mode PTY Program Type modeRT Radio Text mode CT Clock Time modeTo cancel this function Press PTY Seek Mode to set this unitPTY Seek mode PTY Seek functionEON function Special considerations when recording DTS software RecordingSound Field Program Descriptions For movie/video sourcesDolby Digital SUR. Standard Dolby DigitalSUR. Enhanced SUR. StandardPRO Logic SUR. Standard PRO LogicFor music sources Concert HallJazz Club Rock ConcertSelecting the OSD mode Using the sleep timer Setting the sleep timerAdvanced Operations P08 Movie TheaterCanceling the sleep timer Press j / i to adjust the speaker output levelPress Select when you have completed your adjustment Sleep OFFOutputting the test tone from the Presence speakers Using the test tonePress AMP Press Test SET Menu Using SET Menu Press u / d to select Manual SetupPress Select to enter Manual Setup To exit, press SET Menu when finishedSound Menu 1/2 Center SPFront SP Surr L/R SPSurr B L/R SP Presence SPLFE/BASS OUT Cross OverCSP Distance 02ASUBWOOFER PhaseSpeaker distance CSP Distance Dcenter GEQ Elfe LevelFdynamic Range Gaudio SETHPR/SB Select Input MenuCMPNT-V Input Optical OUTBinput Mode CoaxialCinput Rename For Coaxial Input jacks 5Adisplay SET Option MENU1/2Bmemory Guard CPARAM. INI Dzone SETParameter initialization CPARAM. INI Speaker B set SP BRemote Control Features Control areaAdvd DVD Controlling this unitSetting manufacturer codes ManufacturerPress Learn again to exit from the setup mode Controlling other components MD/CDProgramming codes from other remote controls Press Learn using a ballpoint pen or similar objectPress an input selector button to select a source component Learn is displayedChanging source names in the display window Press Clear by using a ballpoint pen or similar object Press u / d to select the clear modePress Clear to exit from the clearing mode Clearing function setsClearing a learned function Clearing individual functionsSelected component name appears in the display window Editing Sound Field Parameters What is a sound field Changing parameter settingsElements of a sound field Resetting parameters to the factory presets To reset a certain parameterTo reset all parameters Press u / d to select the parametersSound Field Parameter Descriptions INIT. DLY Initial delayRoom SIZE/P. Room Size Room size INIT. DLY Surround initial delay SB INIT. DLY Surround back initial delayRoom Size Surround room size Liveness Surround livenessREV.TIME Reverberation time REV.DELAY Reverberation delayREV. Level Reverberation level DIALG.LIFT Dialog lift For 7ch StereoCT Width Center width For DTS Neo6 Music Image Center imageTroubleshooting GeneralSound suddenly Goes offOnly the speaker on One side can beOr DTS indicator on Volume level isRecord Volume level Dolby Digital or DTSTuner RX-V750 Remote control Does not work norFunction properly Does not learn newResetting the Factory Presets Be sure this unit is in standby modeFactory Preset appears in the front panel display Press Straight Effect to select the desired settingGlossary Audio formatsSound field programs Audio informationLFE 0.1 channel PCM Linear PCMVideo signal information Component video signalComposite video signal Video signalSpecifications Audio SectionWC85520