Burnham FM01FD00B manual MPC4 & MPC5

Page 56

v.Connect opposite end of T991A Modulating Control harness to right side junction box cover ‘A’, hole location #4 as shown in Figure 40.

vi.Locate mating connector labeled “LO-HI-

LO/MOD” inside right junction box, see Figure 40. Join mating connectors which are polarized and lock together. Lightly tug on connectors to make sure they are secure.

vii.If no other controls are being installed at this time, secure Cover ‘A’ and Cover ‘B’ to jacket rear top panel with two (2) #8 x 1/2” lg. hex head SMS per cover. Install 7/8” knockout plugs (provided) to all unused holes, refer to Figure 40.

T.Install Flue Outlet Damper Assembly, see Figure 46.

1.Locate flue outlet damper carton, as applicable (see Table below). Open carton remove a flue outlet damper assembly, a flue outlet damper gasket and mounting hardware bag (12 pcs each 5/16 -18 x 7.8” hex head plated cap screws and 1/4” USS plated washers).

2.Assemble two cap screw/washer combinations, then, insert cap screws/washers through a flue outlet damper assembly-mounting ring at 3 o’clock and

9 o’clock positions. Place the flue outlet damper gasket onto cap screws and position damper with gasket onto boiler rear flue collector, aligning screws with flue collector threaded holes.

3.Thread the screws at 3 o’clock and 9 o’clock positions into flue collector threaded holes hand tight.

4.Assemble remaining cap screw/washer combinations, then, insert cap screws/washers through a flue outlet damper assembly-mounting ring/gasket and thread the screws into flue collector threaded holes hand tight.

5.Alternately tighten the screws with an open end or socket head wrench to complete the assembly.

Boiler Model

Flue Outlet Damper

Flue Outlet

Recommended Vent

Carton Part Number

Damper Diameter

Connection Size

 

MPC4 & MPC5

102473-01

7” Dia.

7” Dia.

MPC6 thru MPC8

102473-02

8” Dia.

8” Dia.

MPC9 thru MPC12

102473-03

10” Dia.

10” Dia.

MPC13 thru MPC18

102473-04

12” Dia.

12” Dia.

Figure 46: Install Flue Outlet Damper Assembly

56

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Price $5.00 101786-01R5-11/10Ialcastiron.com Parts Cartons Castings Shipped Loose Field AssemblyKnockdown Boiler Equipment Check List On Bar Number Carton Qty. Req’d. Per Boiler Size Important Information Page Page Table of Contents Section VI Service Instructions Section VII Burner SpecificationsSection Viii Repair Parts Rear CoverDimensional Information Table I Dimensional Information Section I General InformationTable II Ratings/Data Model MPC Boilers CombustionTable III Recommended Rear Service Clearance Section I General InformationBoiler Foundation MPC with Rear Outlet Vent Faulty Boiler Burner Operation Section II Cast Iron Block Assembly Instructions Hydrostatic Test Manual or Hydraulic Draw-up Section Assembly Vertical Bracing of Rear Section Page MPC4 DRAW-UP Page Section III Boiler Assembly Instructions Knockdown Boiler Section III Boiler Assembly Instructions KD Boiler Page Table VII Modular Return Water Mixing Tube Rwmt RC Return Water Mixing Tube RC Assembly and Installation Hand Form Support Channel Bracket Secure Brackets to Horizontal Channel Table Viii Frame/Bracket Mounting LocationsRear Section Horizontal Channel Assembly w/Mounting Hardware Mount Rear Section Horizontal Channel to Block Assembly Attachment of Lower Rear Section Bracket to Casting Leg Page Lower Tie Bar Installation Heat Exchanger Insulation One Piece and Modular Wrappers Internal Wiring Harness Components Page Internal Wiring Harness Components Install Protective Edging Table IX Internal Wiring Harness Adjustment ‘B’ ‘C’ ‘D’Page Step Table X Jacket Top Corner / Intermediate Panel ArrangementInstall Top Corner / Intermediate Panels Jacket Split Rear Panel Detail Installing Jacket Top Panels Viewed From Front Table XI Jacket Top Panel ArrangementInstall Jacket Top Panels Viewed From Rear Avoid Breathing Fiber Particulates and Dust Install 2nd Pass Flueway Baffles Secure Burner Swing Door for Tight Perimeter Seal Beckett ‘CG’ Series Burner Adapter Plate Power Flame ‘JR’ Series Burner Adapter PlateBeckett ‘CF’ Series Burner Adapter Plate Purpose of Tappings in Supply Manifold Install Standard Trim Operating Control Install Probe Low Water Cut Off Install Low Fire Hold Control MPC4 & MPC5 Install Jacket Panels for Optional Burner Swing Door Cover Section IV Installation Instructions Packaged Boiler Shipping InformationRecommended MPC Minimum Piping Single Boiler Application Recommended MPC Minimum Piping Multiple Boiler Application Alternate MPC Minimum Piping Single Boiler Application Alternate MPC Minimum Piping Multiple Boiler Application Parallel Piping Conversion Discharge Piping for Pressure Relief Valve Section V Operating Instructions Test Controls Frequent Water Addition Section VI Service Instructions Maintenance of LOW Water Cutoff Devices Operation Fuel Valves Combustion Safety ControlsFrequency Accomplished by Remarks Table XII Recommended Periodic Testing Check List Section VII Burner Specifications Table XIIIb Beckett Gas Burner SpecificationsTable XIVa Power Flame #2 Oil Burner Specifications Table XIVb Power Flame Gas Burner Specifications500 C1-GO-10 16 / Closed Section Viii Repair Parts Repair Parts Cast Iron Section Assembly MPC Common Bare Boiler Components Repair Parts Common Bare Boiler Components MPC Common Bare Boiler Components Repair Parts Common Bare Boiler Components Oil BurnerGas Burner Oil, Gas, Gas/Oil Combo BurnerMPC Front & Center Section Frame Rail Assembly Repair Parts Front & Center Section Frame Rail Assembly MPC Rear Section Frame Rail Assembly Repair Parts Rear Section Frame Rail Assembly MPC Return Water Mixing Tube RC Assembly Repair Parts Return Water Mixing Tube RC Assembly RequiredMPC Heat Exchanger Insulation Wrapper Repair Parts Heat Exchanger Insulation Wrapper MPC Internal Wiring Harness Components Repair Parts Internal Wiring Harness Components MPC Jacket Panel Assembly Repair Parts Jacket Panel Assembly MPC Jacket Panel Assembly Repair Parts Jacket Panel Assembly MPC 2nd and 3rd Pass Flueway Baffles Repair Parts MPC 2ND and 3RD Pass Flueway Baffles Page Description 100 101 Optional Working Pressure Trim102 Repair Parts Common Optional Controls Appendix a Figures Description 106 Appendix B Tables Limited Warranty

FM01FD00B specifications

The Burnham FM01FD00B is a remarkable heating solution that combines efficiency, reliability, and advanced technology to meet the demands of modern homes and commercial spaces. Standing out in the crowded market of heating systems, the FM01FD00B is designed for those who prioritize both performance and energy savings.

One of the most significant features of the Burnham FM01FD00B is its advanced combustion technology. The system utilizes a high-efficiency burner that maximizes fuel usage, resulting in lower operating costs and reduced environmental impact. The unit is engineered to provide consistent heat distribution, ensuring that every corner of a room reaches a comfortable temperature quickly and effectively.

In addition to its efficient burning capabilities, the FM01FD00B is compatible with multiple heating mediums, allowing it to adapt to various fuel types, including natural gas and propane. This versatility makes it an excellent choice for homeowners looking for flexible heating options that can cater to their specific needs.

The FM01FD00B also comes equipped with a state-of-the-art control system that offers precise temperature management. Users can easily program their desired heating schedule, ensuring optimal comfort at all times. The intuitive interface allows for easy adjustments, making it simple to maintain a cozy environment whether at home or away.

Another key characteristic is the unit's robust construction. Built with high-quality materials, the Burnham FM01FD00B is designed to withstand harsh conditions and provide lasting performance. The durable exterior is resistant to corrosion, further enhancing its longevity and reliability.

Moreover, the system features built-in safety mechanisms that protect against overheating and other potential hazards, ensuring peace of mind for users. This focus on safety extends to its low emissions, making it an eco-friendly choice for those looking to reduce their carbon footprint.

In conclusion, the Burnham FM01FD00B is a high-efficiency heating solution that excels in performance, adaptability, and safety. Its advanced technologies, robust construction, and user-friendly features make it an ideal choice for anyone seeking a dependable and efficient heating system for their home or business. Whether you prioritize energy savings, reliability, or comfort, the FM01FD00B stands out as a top contender in the heating market.
Top Page Image Contents