Burnham FM01FD00B manual Install Low Fire Hold Control

Page 55

Figure 43: Install Low Fire Hold Control

c.Connect opposite end of L4006B Low Fire Hold Control harness to right side junction box cover ‘A’, hole location #2 as shown in Figure 40.

d.Locate mating connector labeled “Low Fire

Hold” inside right junction box. Join mating connectors which are polarized and lock together. Lightly tug on connectors to make sure they are secure.

e.Proceed to next appropriate control option listed below for installation details. If no other controls are being installed at this time, secure Cover ‘A’ and Cover ‘B’ to jacket rear top panel with two (2) #8 x 1/2” lg. hex head SMS per cover. Install 7/8” knockout plugs (provided) to all unused holes, refer to Figure 40.

4.Install Low/High/Low Control or Modulating Control

a.Install Low/High/Low Control as follows (for modulating control, proceed to Step b):

i.Apply thread sealant to 3/4” immersion well and install in Tapping ‘H’ as shown in Figure 38. Wrench well until water tight.

ii.Locate L4006A Low/High/Low Control and remove knockout on casing closest to mounting hole. Connect end of harness with forked terminals to casing knockout. Connect black and gray wires to terminals on Low/High/Low Control, wires are interchangeable. Refer to Figure 44.

iii.Connect opposite end of L4006A Low/High/ Low Control harness to junction box cover ‘A’, hole location #4 as shown in Figure 40.

iv.Locate mating connector labeled “LO-HI-

LO/MOD” inside right junction box. Join mating connectors which are polarized and lock together. Lightly tug on connectors to make sure they are secure.

v.Proceed to next appropriate control option listed below for installation details. If no other controls are being installed at this time, secure Cover ‘A’ and Cover ‘B’ to jacket rear top panel with two (2) #8 x 1/2”

lg. hex head SMS per cover. Install 7/8” knockout plugs (provided) to all unused holes, refer to Figure 40.

b. Install Modulating Control as follows:

i. Apply thread sealant to 3/4” immersion well and install in Tapping ‘H’ as shown in Figure 38. Wrench well until water tight.

ii.Locate T991A Modulation control and remove knockout on casing closest to temperature control knob. Connect end of harness with forked terminals to casing knockout.

Figure 44: Install Low/High/Low Control

Connect wires to terminals as follows:

B Terminal - Black Wire w/White Tracer

W Terminal - Gray Wire

R Terminal - Red Wire w/White Tracer

iii.Install Remote Sensing Bulb into control well and secure with retaining clip. Coil excess sensor tubing as shown in Figure 45.

iv.Mount T991A Control to rear panel on left side of return manifold with two (2) self drilling #8 x 1/2” lg. hex head SMS (provided) as shown in Figure 45.

Figure 45: Install Modulation Control

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Ialcastiron.com 101786-01R5-11/10Price $5.00 Knockdown Boiler Equipment Check List Castings Shipped Loose Field AssemblyParts Cartons On Bar Number Carton Qty. Req’d. Per Boiler Size Important Information Page Page Table of Contents Rear Cover Section VI Service InstructionsSection VII Burner Specifications Section Viii Repair PartsDimensional Information Section I General Information Table I Dimensional InformationCombustion Table II Ratings/Data Model MPC BoilersSection I General Information Table III Recommended Rear Service ClearanceBoiler Foundation MPC with Rear Outlet Vent Faulty Boiler Burner Operation Section II Cast Iron Block Assembly Instructions Hydrostatic Test Manual or Hydraulic Draw-up Section Assembly Vertical Bracing of Rear Section Page MPC4 DRAW-UP Page Section III Boiler Assembly Instructions Knockdown Boiler Section III Boiler Assembly Instructions KD Boiler Page Table VII Modular Return Water Mixing Tube Rwmt RC Return Water Mixing Tube RC Assembly and Installation Hand Form Support Channel Bracket Table Viii Frame/Bracket Mounting Locations Secure Brackets to Horizontal ChannelRear Section Horizontal Channel Assembly w/Mounting Hardware Mount Rear Section Horizontal Channel to Block Assembly Attachment of Lower Rear Section Bracket to Casting Leg Page Lower Tie Bar Installation Heat Exchanger Insulation One Piece and Modular Wrappers Internal Wiring Harness Components Page Internal Wiring Harness Components Install Protective Edging ‘B’ ‘C’ ‘D’ Table IX Internal Wiring Harness AdjustmentPage Table X Jacket Top Corner / Intermediate Panel Arrangement StepInstall Top Corner / Intermediate Panels Jacket Split Rear Panel Detail Table XI Jacket Top Panel Arrangement Installing Jacket Top Panels Viewed From FrontInstall Jacket Top Panels Viewed From Rear Avoid Breathing Fiber Particulates and Dust Install 2nd Pass Flueway Baffles Secure Burner Swing Door for Tight Perimeter Seal Beckett ‘CF’ Series Burner Adapter Plate Power Flame ‘JR’ Series Burner Adapter PlateBeckett ‘CG’ Series Burner Adapter Plate Purpose of Tappings in Supply Manifold Install Standard Trim Operating Control Install Probe Low Water Cut Off Install Low Fire Hold Control MPC4 & MPC5 Install Jacket Panels for Optional Burner Swing Door Cover Packaged Boiler Shipping Information Section IV Installation InstructionsRecommended MPC Minimum Piping Single Boiler Application Recommended MPC Minimum Piping Multiple Boiler Application Alternate MPC Minimum Piping Single Boiler Application Alternate MPC Minimum Piping Multiple Boiler Application Parallel Piping Conversion Discharge Piping for Pressure Relief Valve Section V Operating Instructions Test Controls Frequent Water Addition Section VI Service Instructions Maintenance of LOW Water Cutoff Devices Operation Frequency Accomplished by Remarks Combustion Safety ControlsFuel Valves Table XII Recommended Periodic Testing Check List Table XIIIb Beckett Gas Burner Specifications Section VII Burner SpecificationsTable XIVb Power Flame Gas Burner Specifications Table XIVa Power Flame #2 Oil Burner Specifications500 C1-GO-10 16 / Closed Section Viii Repair Parts Repair Parts Cast Iron Section Assembly MPC Common Bare Boiler Components Repair Parts Common Bare Boiler Components MPC Common Bare Boiler Components Oil, Gas, Gas/Oil Combo Burner Repair Parts Common Bare Boiler ComponentsOil Burner Gas BurnerMPC Front & Center Section Frame Rail Assembly Repair Parts Front & Center Section Frame Rail Assembly MPC Rear Section Frame Rail Assembly Repair Parts Rear Section Frame Rail Assembly MPC Return Water Mixing Tube RC Assembly Required Repair Parts Return Water Mixing Tube RC AssemblyMPC Heat Exchanger Insulation Wrapper Repair Parts Heat Exchanger Insulation Wrapper MPC Internal Wiring Harness Components Repair Parts Internal Wiring Harness Components MPC Jacket Panel Assembly Repair Parts Jacket Panel Assembly MPC Jacket Panel Assembly Repair Parts Jacket Panel Assembly MPC 2nd and 3rd Pass Flueway Baffles Repair Parts MPC 2ND and 3RD Pass Flueway Baffles Page Description 100 Optional Working Pressure Trim 101102 Repair Parts Common Optional Controls Appendix a Figures Description 106 Appendix B Tables Limited Warranty

FM01FD00B specifications

The Burnham FM01FD00B is a remarkable heating solution that combines efficiency, reliability, and advanced technology to meet the demands of modern homes and commercial spaces. Standing out in the crowded market of heating systems, the FM01FD00B is designed for those who prioritize both performance and energy savings.

One of the most significant features of the Burnham FM01FD00B is its advanced combustion technology. The system utilizes a high-efficiency burner that maximizes fuel usage, resulting in lower operating costs and reduced environmental impact. The unit is engineered to provide consistent heat distribution, ensuring that every corner of a room reaches a comfortable temperature quickly and effectively.

In addition to its efficient burning capabilities, the FM01FD00B is compatible with multiple heating mediums, allowing it to adapt to various fuel types, including natural gas and propane. This versatility makes it an excellent choice for homeowners looking for flexible heating options that can cater to their specific needs.

The FM01FD00B also comes equipped with a state-of-the-art control system that offers precise temperature management. Users can easily program their desired heating schedule, ensuring optimal comfort at all times. The intuitive interface allows for easy adjustments, making it simple to maintain a cozy environment whether at home or away.

Another key characteristic is the unit's robust construction. Built with high-quality materials, the Burnham FM01FD00B is designed to withstand harsh conditions and provide lasting performance. The durable exterior is resistant to corrosion, further enhancing its longevity and reliability.

Moreover, the system features built-in safety mechanisms that protect against overheating and other potential hazards, ensuring peace of mind for users. This focus on safety extends to its low emissions, making it an eco-friendly choice for those looking to reduce their carbon footprint.

In conclusion, the Burnham FM01FD00B is a high-efficiency heating solution that excels in performance, adaptability, and safety. Its advanced technologies, robust construction, and user-friendly features make it an ideal choice for anyone seeking a dependable and efficient heating system for their home or business. Whether you prioritize energy savings, reliability, or comfort, the FM01FD00B stands out as a top contender in the heating market.
Top Page Image Contents