Ariston 41-116-04 installation instructions Siting the Appliance, Overall Dimensions, Clearances

Page 5

2.2 SITING THE APPLIANCE

 

 

mm400

 

 

60 mm

132

132

 

C

E

mm

 

 

300

FIG. 2.1

 

 

The appliance may be installed in any room or indoor area, although particular attention is drawn to the requirements of the current I.E.E. Wiring Regulations, and in Scotland, the electrical provisions of the Building Regulations applicable in Scotland, with respect to the installation of the appliance in a room containing a bath or shower.

Where a room-sealed appliance is installed in a room containing a bath or shower the appliance and any electrical switch or appliance control, utilising mains electricity should be situated so that it cannot be touched by a person using the bath or shower.

The location must permit adequate space for servicing and air circulation around the appliance as indicated in paragraph 2.4.

The location must permit the provision of an adequate flue and termination. For unusual locations special procedures may be necessary.

BS 6798-1987 gives detailed guidance on this aspect.

A compartment used to enclose the appliance must be designed specifically for this purpose. No specific ventilation requirements are needed for the installation within a cupboard.

This appliance is not suitable for outdoor installation.

The type C appliances (in which the combustion circuit, air vent intake and combustion chamber are air-tight with respect to the room in which the appliance is installed) can be installed in any type of room.

Secondary ventilation is not required with this boiler. The boiler must be installed on a solid, permanent wall to prevent access from the rear.

2.3OVERALL DIMENSIONS

LEGEND:

A= Central Heating Flow (3/4”)

C = Gas Inlet (3/4”)

E= Central Heating Return (3/4”) mm = Clearances

450 mm

2.4CLEARANCES

In order to allow for access to the interior of the boiler for maintenance purposes, the boiler must be installed in compliance with the minimum clearances indicated in FIG. 2.1

2.5MOUNTING THE APPLIANCE

2.6ELECTRICAL CONNECTION

Fasten the boiler in place using the template and anchors supplied with the unit. It is highly recommended that a spirit level be used to position the boiler so that it is perfectly level.

For additional information, please consult the instructions contained in the connection kit and the flue kit.

For safety purposes, have a competent person carefully check the electrical system in the property, as the manufacturer will not be held liable for damage caused by the failure to earth the appliance properly or by anomalies in the supply of power. Make sure that the residential electrical system is adequate for the maximum power absorbed by the unit, which is indicated on the rating plate. In addition, check that the section of cabling is appropriate for the power absorbed by the boiler.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Installation Instructions Type C Boilers Table of Contents General Instructions Reference Standards InstallationOverall View Siting the Appliance Overall DimensionsClearances Mounting the Appliance Electrical ConnectionWater Connections GAS ConnectionResidual Head of the Boiler Tower Flue Components Flue ConnectionsRoom Thermostat Connection RffiOn/Off Switch Electrical DiagramGAS and Water Circuits H.W. Storage Cylinder 2 Port and 3 Port Valve InstallationsModel Initial Preparation CommissioningDomestic HOT Water Priority KIT Removing the Front Panel Control PanelFume Discharge Monitoring Initial START-UP Combustion AnalysisBoiler Safety Systems Draining the System Changing the Type of GAS GAS AdjustmentsRffi Maintenance Number 41-116-04 Technical InformationServicing Instructions Type C Boilers Fault Finding To Gain General Access Replacement of PartsServicing Instructions Removing the front panelRemoving the side panels Removing the sealed chamber front coverRemoving the combustion cover Access to the Combustion ChamberRemoving the burner and jets Removing the electrodesRemoving the main heat exchanger Removing the fan Removing the air pressure switchServicing and Removal of the GAS Valve Setting the gas pressuresRffi Removing the gas valve Removing the spark generatorRemoving the safety valve Removing the pump pressure switchAccess to the Water Circuit Removing the automatic air vent 1. Unscrew valve top Z FIGRemoving the pump Removing the expansion vessel Removing the pressure gaugeRemoving the regulation thermostat Removing the overheat thermostatRemoving the frost thermostat Removing the P.C.B.s Access to the Control SystemChecking the fuse Flow -CHARTS Fault FindingFault Finding Guide YES Mbar Electrical DiagramsSF008A MicroSYSTEM 10 Rffi Ariston B063 Technical Service Hot Line 01494 23 99 84 1582

41-116-04 specifications

The Ariston 41-116-04 is a remarkable piece of technology that epitomizes modern design and performance in the home appliance sector. This innovative unit stands out for its blend of practicality and sophistication, making it a favorite among consumers seeking efficiency and elegance in their daily lives.

At the heart of the Ariston 41-116-04 lies its impressive energy efficiency. This appliance boasts an advanced A+ energy rating, ensuring minimal energy consumption while still delivering optimal performance. This not only contributes to lowering utility bills but also aligns with environmentally friendly practices, making it a responsible choice for eco-conscious consumers.

One of the key features of the Ariston 41-116-04 is its user-friendly interface. With intuitive controls and a clear digital display, users can easily navigate through various settings and options. This thoughtful design simplifies operation, allowing for a seamless experience whether you are a tech-savvy individual or someone who prefers straightforward functionality.

The versatility of the Ariston 41-116-04 is another considerable advantage. It offers multiple modes tailored for different cooking styles, ensuring that meals can be prepared to perfection regardless of the dish. Whether you need to bake, grill, or steam, this model provides an array of cooking options that cater to diverse culinary preferences.

The appliance also incorporates innovative technologies to enhance performance. For instance, the advanced heat distribution system ensures even cooking results, eliminating hotspots and guaranteeing uniformly cooked meals. The incorporation of high-quality materials in its construction offers durability and robust performance, an essential characteristic for any long-lasting appliance.

In terms of safety, the Ariston 41-116-04 is designed with multiple safety features, including an automatic shut-off and child lock functions. These elements provide peace of mind for families, knowing that safety is a priority in all operations.

In conclusion, the Ariston 41-116-04 is a stellar appliance that encompasses efficiency, user-friendliness, and advanced cooking technologies. With its emphasis on energy conservation and safety, it represents an excellent investment for any modern household looking to enhance their culinary experience while maintaining a commitment to sustainability.
Top Page Image Contents