Desa VSL18NT, VSL18PT installation manual Installing Heater to Wall

Page 10

INSTALLATION

Continued

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket that has been taped to back panel of heater for shipping. Remove mount- ing bracket from back panel of heater.

Figure 9 - Mounting Bracket

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes centers are 13" (33 cm) apart. Attach mounting bracket to wall in one of two ways:

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain mini- mumclearancesshowninFigure

10.If you can, provide greater clearances from floor and join- ing wall.

2.Mark screw locations on wall (see Figure 10).

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

Attaching Mounting Bracket To Wall Note: Wall anchors, mounting screws and spacers are in hardware package. The hardware package is provided with heater.

 

12"

13" (33 cm)

 

 

(30.4

 

 

 

cm)

 

 

AdjoiningWall

Min.

 

 

Only Insert Mounting

11"

Screws Through Last

(27.9 cm)

 

 

Hole On Each End

Min.

 

 

 

Floor

Figure 10 - Mounting Bracket Clearances

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 11.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls [1/2" (1.3 cm) or less], insert red key into wall anchor. Push red key to “pop” open anchor wings. IMPORTANT: Do not hammer key! For thick walls [over 1/2" (1.3 cm) thick] or solid walls, do not pop open wings.

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

Figure 11 - Folding Anchor

Figure 12 - Popping Open Anchor Wings

For Thin Walls

10

www.desatech.com

116292-01D

Image 10
Contents What to do if YOU Smell GAS Table of Contents Safety Information Product Identification Product FeaturesLocal Codes UnpackingFollowing are excerpts from National Fuel AIR for Combustion VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceCheck GAS Type InstallationVentilation AIR Ventilation Air From Inside BuildingInstalling Glass Panel Installation ItemsInstalling Ignitor Removing Front Panel of HeaterLocating Heater This heater is designed to be mounted on a wallInstalling Heater to Wall Installing Bottom Mounting Screws Connecting to GAS SupplyPlacing Heater On Mounting Bracket Checking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPa Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaOperating Heater Connecting to Electrical SupplyFor Your Safety Read Before Lighting Extension CordThermostat Control Operation Lighting InstructionsTo Turn OFF GAS To Appliance Shutting Off HeaterBurner Flame Pattern Manual Lighting ProcedureInspecting Heater Pilot Flame PatternBurner Pilot AIR Inlet Cleaning MaintenanceODS/PILOT and Burner CabinetTroubleshooting Observed Problem Possible Cause RemedyBurner orifice is clogged Clean burner see Cleaning Goes out when control knob is Control knob not pressedDelayed ignition of burner Manifold pressure is too low ODS/pilot lights but flameSlight smoke or odor during Walls or furniture Cleaners, etc. may turn intoNo power to electric outlet 60Hz outlet Air passageways on heaterMent above For purposes of input adjustment SpecificationsWiring Diagrams LSL18NT, SL18NT and VSL18NT LSL18PT, SL18PT and VSL18PTReplacement Parts AccessoriesTechnical Service Service Publications Service HintsIllustrated Parts Breakdown Models LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT and VSL18PTParts List Parts Centrals 116292-01D Warranty Information Keep this WarrantyQUÉ Hacer SI Percibe Olor a GAS Tabla DE Contenido Información DE Seguridad Desempaque Información DECódigos Locales Características DEL ProductoConstrucción inusualmente sellada Aire Para Combustión VentilaciónCómo Proveer LA Ventilación Adecuada Espacio confinado y no confinadoAire Para Ventilación Aire del interior de la construcción para ventilaciónVerifique EL Tipo DE GAS InstalaciónAire del exterior para ventilación Instalación DEL Encendedor Artículos DE InstalaciónDesmontaje DEL Panel Anterior DEL Calentador Instalación del panel de vidrioCorrientes de aire fuertes Ubicación DEL CalentadorSoporte de montaje Instalación DEL Calentador EN LA ParedDoble el anclaje de pared como se muestra en la figura Instalación de los tornillos de montaje Conexión AL Suministro DE GASColocación del calentador en el soporte de montaje InferioresLo suficientemente grande para que Permita el paso del volumen de gasRevisión DE LAS Conexiones DE GAS Adecuado al calentador. Si la tuberíaUsando aire comprimido Cierre del equipoRegule la presión del sistema de tubería de Repare todas las fugas inmediatamenteCable DE Extensión Funcionamiento DEL CalentadorConexión a LA Alimentación Eléctrica Para SU SEGURIDAD, LEA Esto Antes DE EncenderloInstrucciones DE Encendido Funcionamiento DELApague el piloto Calentador Funcionamiento DELPatrón DE LA Llama DEL Procedimiento DEEntrada DE Aire AL Piloto DEL Quemador Limpieza Y MantenimientoPiloto CON ODS Y Quemador GabineteLa posición del regulador de gas no es la correcta Solución DE ProblemasProblema Observado Causa Posible Remedio Reemplace el regulador de gasCausa Posible Remedio Línea de gas El problema desapareceráHay aire en la línea de gas Hasta que se elimine el aire Los conductos de aire en elCia anterior LSL18NT, SL18NT y VSL18NT Diagramas DE CableadoEspecificaciones LSL18PT, SL18PT y VSL18PTPublicaciones DE Servicio AccesoriosServicio Técnico Piezas DE RepuestoClasificación Ilustrada DE Piezas Modelos LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT Y VSL18PTLista DE Piezas Laporte’s Parts & Service 2444 N th Street Centrales DE PiezasNotas Información DE Garantía Guarde Esta Garantía