Desa VSL18NT, VSL18PT Inspecting Heater, Manual Lighting Procedure, Burner Flame Pattern

Page 16

OPERATING HEATER

Continued

Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet. This may not always agree with room tem- perature (depending on housing construction, installation location, room size, open air tem- peratures, etc.). Frequent use of your heater will let you determine your own comfort levels.

Thermocouple

Yellow Flame

Pilot

Burner

MANUAL LIGHTING PROCEDURE

Figure 25 - Incorrect Pilot Flame Pattern

BURNER FLAME PATTERN

1.Remove front panel (see Figure 4, page 8).

2.Follow steps 1 through 7 under Lighting Instructions, page 15.

3.With control knob pressed in, strike match. Hold match to pilot until pilot lights.

4.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 9, under Lighting Instructions, page 15.

5.Replace front panel.

INSPECTING HEATER

Check pilot flame pattern and burner flame pat- tern often.

PILOT FLAME PATTERN

Figure 24 shows a correct pilot flame pattern. Figure 25 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 25

WARNING: If yellow tipping occurs, your heater could pro- duce increased levels of carbon monoxide.

NOTICE: Do not mistake orange flames with yellow tipping. Dirt or other fine particles enter the heater and burn causing brief patches of orange flame.

Figure 26 shows a correct burner flame pattern. Figure 27 shows an incorrect burner flame pattern. The incorrect burner flame pattern shows yellow tipping of the flame. It also shows the flame higher than 1/2 the deflector panel height.

If burner flame pattern is incorrect, as shown in Figure 27

turn heater off (see To Turn Off Gas To Appli- ance, page 15)

see Troubleshooting, page 18

turn heater off (see To Turn Off

Gas to Appliance,

Blue

Flame

 

page 15)

 

 

 

1/2

see Troubleshooting, page 18

 

Note: The pilot flame on natural gas units will

Deflector

Height

have a slight curve, but flame should be blue and

Figure 26 - Correct Burner Flame Pattern

have no yellow or orange color.

 

Blue Flame

Thermocouple

Pilot

Burner

Yellow

Tipping

1

/2

 

Deflector

Height

Figure 27 - Incorrect Burner Flame

Pattern

Figure 24 - Correct Pilot Flame Pattern

16

www.desatech.com

116292-01D

Image 16
Contents What to do if YOU Smell GAS Table of Contents Safety Information Product Features Local CodesProduct Identification UnpackingAIR for Combustion Ventilation Providing Adequate VentilationFollowing are excerpts from National Fuel Unusually Tight ConstructionDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceInstallation Ventilation AIRCheck GAS Type Ventilation Air From Inside BuildingInstallation Items Installing IgnitorInstalling Glass Panel Removing Front Panel of HeaterLocating Heater This heater is designed to be mounted on a wallInstalling Heater to Wall Installing Bottom Mounting Screws Connecting to GAS SupplyPlacing Heater On Mounting Bracket Checking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPa Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaConnecting to Electrical Supply For Your Safety Read Before LightingOperating Heater Extension CordLighting Instructions To Turn OFF GAS To ApplianceThermostat Control Operation Shutting Off HeaterManual Lighting Procedure Inspecting HeaterBurner Flame Pattern Pilot Flame PatternCleaning Maintenance ODS/PILOT and BurnerBurner Pilot AIR Inlet CabinetTroubleshooting Observed Problem Possible Cause RemedyGoes out when control knob is Control knob not pressed Delayed ignition of burner Manifold pressure is too lowBurner orifice is clogged Clean burner see Cleaning ODS/pilot lights but flameWalls or furniture Cleaners, etc. may turn into No power to electric outlet 60Hz outletSlight smoke or odor during Air passageways on heaterMent above Specifications Wiring DiagramsFor purposes of input adjustment LSL18NT, SL18NT and VSL18NT LSL18PT, SL18PT and VSL18PTAccessories Technical ServiceReplacement Parts Service Publications Service HintsIllustrated Parts Breakdown Models LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT and VSL18PTParts List Parts Centrals 116292-01D Warranty Information Keep this WarrantyQUÉ Hacer SI Percibe Olor a GAS Tabla DE Contenido Información DE Seguridad Información DE Códigos LocalesDesempaque Características DEL ProductoAire Para Combustión Ventilación Cómo Proveer LA Ventilación AdecuadaConstrucción inusualmente sellada Espacio confinado y no confinadoAire Para Ventilación Aire del interior de la construcción para ventilaciónVerifique EL Tipo DE GAS InstalaciónAire del exterior para ventilación Artículos DE Instalación Desmontaje DEL Panel Anterior DEL CalentadorInstalación DEL Encendedor Instalación del panel de vidrioCorrientes de aire fuertes Ubicación DEL CalentadorSoporte de montaje Instalación DEL Calentador EN LA ParedDoble el anclaje de pared como se muestra en la figura Conexión AL Suministro DE GAS Colocación del calentador en el soporte de montajeInstalación de los tornillos de montaje InferioresPermita el paso del volumen de gas Revisión DE LAS Conexiones DE GASLo suficientemente grande para que Adecuado al calentador. Si la tuberíaCierre del equipo Regule la presión del sistema de tubería deUsando aire comprimido Repare todas las fugas inmediatamenteFuncionamiento DEL Calentador Conexión a LA Alimentación EléctricaCable DE Extensión Para SU SEGURIDAD, LEA Esto Antes DE EncenderloInstrucciones DE Encendido Funcionamiento DELApague el piloto Funcionamiento DEL Patrón DE LA Llama DELCalentador Procedimiento DELimpieza Y Mantenimiento Piloto CON ODS Y QuemadorEntrada DE Aire AL Piloto DEL Quemador GabineteSolución DE Problemas Problema Observado Causa Posible RemedioLa posición del regulador de gas no es la correcta Reemplace el regulador de gasCausa Posible Remedio El problema desaparecerá Hay aire en la línea de gas Hasta que se elimine el aireLínea de gas Los conductos de aire en elCia anterior Diagramas DE Cableado EspecificacionesLSL18NT, SL18NT y VSL18NT LSL18PT, SL18PT y VSL18PTAccesorios Servicio TécnicoPublicaciones DE Servicio Piezas DE RepuestoClasificación Ilustrada DE Piezas Modelos LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT Y VSL18PTLista DE Piezas Laporte’s Parts & Service 2444 N th Street Centrales DE PiezasNotas Información DE Garantía Guarde Esta Garantía