Heatiator Log Set Assembly LOGS-NDI30 Models NDI30, NDI30-SP, Install the Log Assembly, LOG #5

Page 31

G. Install the Log Assembly

Log Set Assembly: LOGS-NDI30

Models: NDI30, NDI30-SP

CAUTION: Logs are fragile, handle with care.

PILOT

LOG SHELF

BRACKET

 

LOG PINS

GRATE BAR

GRATE

TINES

Figure 1.

SRV2226-701

 

SRV2226-705

 

 

SRV2226-704

 

SRV2226-706

SRV2226-703

 

SRV2226-702

 

FLAT SPOT FOR

FLAT SPOT FOR

LOG #5

FLAT SPOT FOR

 

LOG #6

LOG #4

 

 

 

 

1

 

LOG

 

 

NOTCH

 

 

Figure 2. Install Log #1

 

 

Log #1 (SRV2226-701)Position Log #1 as shown in Figure 2. Note additional placement instructions in Figure 1. Set the rear log (Log #1) on the log shelf. Position the log against the back of the firebox. Center the log notch over the pilot bracket.

FLAT SPOT FOR

FLAT SPOT

LOG #5

FOR LOG #6

2

MATE LOG

LOG

PIN WITH

TOUCHES

LOG SLOT

GRATE TINE

Figure 3. Place Log #2

SLOT

Figure 4. Log #2

Log #2 (SRV2226-702): Position Log #2 as shown in Figure 3. Refer to Figure 1 and Figure 4 for additional details. Mate the slot located on the bottom of Log #2 with the log pin located on the right side of the burner. Move the right end of Log #2 forward until it comes into contact with the grate tine.

Heatilator • NDI30, NDI30-SP, NDI35, NDI35-SP, NDI30-SPFK, NDI35-SPFK2226-900 Rev. G • 4/11

31

Image 31
Contents What to do if you smell gas ModelsHOT Surfaces Homeowner Reference Information CongratulationsXxxxxxxx User Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Before Lighting Fireplace Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear SpaceGAS Valve Lighting Instructions IPIFinal inspection by What to do if YOU Smell GASLighting Instructions Standing Pilot For Your Safety Read Before Lighting Lighting InstructionsIssue Solutions Frequently Asked QuestionsAfter Appliance is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingStanding Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components NDI35 NDI30 Fireplace Size RequirementsMinimum Fireplace Opening TOP View Front View Side View Minimum Fireplace SizeSide View TOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent Limitsfi replace opening Placing, Securing and Leveling the Appli- anceDamper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsStanding Pilot Ignition System Wiring IntelliFire Ignition System WiringRED Pilot Assembly Thermocouple ThermopileValve WHT Blower Plug 120V Existing Outlet Temperature Sensor Switch Optional Accessories RequirementsInstallation for Fan Optional Clearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup LOG #6 Log Set Assembly LOGS-NDI30 Models NDI30, NDI30-SPInstall the Log Assembly LOG #5LOG Log Set Installed Log Set Assembly LOGS-NDI35 Models NDI35, NDI35-SPGrate Tine Slot Air Shutter Settings Air Shutter SettingNDI30 NDI35 Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Ignition System Ues to spark, and main Model Dimensions Appliance Dimension DiagramReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsContact Information