Eagle Home Products Eagle Series Alarm Lights, Battery Charger Connector, Interface Port, Buzzer

Page 12

Alarm Lights

Two ultra-bright, red, light-emitting diodes (LEDs) provide visual alarms for gas concentrations and malfunctions. They are mounted on the top rear of the case for greatest visibility.

Battery Charger Connector

The battery charger connector is mounted on the top right rear of the case. The external battery charger connects to this connector to recharge nickel-cadmium (Ni-Cd) batteries. The continuous operation adapter also connects to the battery charger connector.

Interface Port

The interface port is for the optional data logging or remote buzzer. The port is mounted on the top left rear of the case. When the Data Logging option is installed, the Eagle records gas concentrations at programmed intervals and stores data on gas detected. You can download these measurements through the interface port to a PC- compatible computer for use in data analysis programs. Data retrieval requires the Eagle Data Downloader Kit (with PC connection cable and software).

The optional remote buzzer also connects to the interface port. The remote buzzer is for use in applications where a remote alarm indication is required.

Buzzer

A solid-state electronic buzzer is mounted inside the top of the case. The buzzer sounds for gas alarms, malfunction, low battery voltage, and as an indicator during use of the Eagle’s many display and adjustment options.

Sample-Drawing System

The sample-drawing system includes the pump, sensor block and connections, internal ﬁlter and charcoal scrubber, and the external hose, probe, and hydrophobic ﬁlter. This system provides continuous ﬂow of sampled air to the sensors while keeping out liquids and dust.

With proper setup, the system can draw a sample ﬂow from up to 100 feet away from the Eagle. Consult RKI Instruments, Inc., for sample ﬂow distances longer than 100 feet.

6 • Description

Eagle Instruction Manual

Image 12

Contents

Portable Multi-Gas Detector RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510Warranty WarrantyTable of Contents Display Mode Table of ContentsCalibration Appendix F Eagle Tank Tester Model Introduction OverviewIntroduction About this Manual Specifications SpeciﬁcationsEagle Speciﬁcations Standard Sensor Speciﬁcations Combustible OxygenCarbon Description CaseControl Panel ButtonsAlarm Lights Battery Charger ConnectorInterface Port BuzzerSensors Methane Elimination Switch CAL/SETUP SwitchCircuit Boards Operation Starting Up the EagleOperation Operation Normal Operation Monitoring Combustible Gas in the PPM RangeFull Response Mode Conversion Factors Methane Calibration Monitoring Combustible Gases Other than MethaneTarget Gas LEL Factor Setting User Access Turning Off the EagleAlarms Alarm IndicationsAlarms Stel alarm toxics only Low ﬂow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms Display Mode Display ModeUser and Station ID Screen Peak Screen Elapsed Time ScreenTo enter a user and station ID Battery Voltage Screen TWA/STEL ScreenDate/Time Screen Clear Data Logger Screens Remaining Log Time ScreenTo clear the data log Setup Mode Tips for Using Setup ModeSetup Mode Entering Setup Mode Updating the Battery Type SettingUpdating Channel Settings Setting a custom target gas label Fullscale PPM Readings Equivalent to 100% LEL Target GasUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Lunch Break Setting Updating the Eagle’s Serial NumberUpdating the Alarm Latching Setting Updating the Alarm Silence SettingUpdating the Auto Calibration Settings Turning the User ID Function On or OffUpdating the Back Light Setting Turning the Auto Fresh Air Function On or OffUpdating the Interval Time Setting data log option Updating Log Data Over Write Setting data log optionUpdating the Time Calibration Setting data log option Updating the Date and Time Settings data log optionUpdating the Zero Follow Settings Updating the Conﬁrmation Beep SettingReturning to Default Settings To reset all default settings To reset all default alarm point settingsTo reset the oxygen zero setting Calibration Calibration Supplies and EquipmentPreparing for Calibration CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Maintenance Displaying the Battery VoltageTo display the battery voltage Replacing Alkaline BatteriesReplacing Sensors To replace the combustibles sensorTo replace the oxygen sensor To replace the H2S or CO sensor Appendix a Parts List Parts ListAppendix a Parts List Part Number DescriptionPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Appendix C Non-Standard Toxic Gas Sensors SpeciﬁcationsDescription Non-Standard Toxic Gas Sensors SpeciﬁcationsCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Parts List Non-Standard Toxic Gas SensorsAlarm TWA Alarm Stel Alarm Appendix D Carbon Dioxide SensorsCarbon Dioxide Sensor Speciﬁcations Appendix D Carbon Dioxide SensorsNormal Operation of Carbon Dioxide Sensors Demand Zero for Carbon Dioxide SensorsCalibrating Carbon Dioxide Sensors Carbon Dioxide Fresh Air ReadingsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Carbon Dioxide Sensors Range Alarm TWA Alarm Stel Alarm Appendix E Infrared Methane SensorsTarget Gases Infrared Methane Sensor SpeciﬁcationsCalibrating Infrared Methane Sensors Sensor Analog PCB SocketParts List Infrared Methane Sensors Replacing Infrared Methane SensorsTo use the ﬂoat probe assembly Appendix F Eagle Tank Tester ModelAlarms To eliminate an oxygen alarm that is not being usedTo attach the dilution ﬁtting Appendix F Eagle Tank Tester ModelParts List Eagle Tank Tester Model CalibrationAppendix G Five-Gas and Six-Gas Models Displaying Additional ChannelsAppendix G Five-Gas and Six-Gas Models Calibration, Display, and Setup Modes Appendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board