Eagle Home Products Eagle Series instruction manual Appendix F Eagle Tank Tester Model

Page 73

Appendix F: Eagle Tank Tester Model

The Eagle Tank Tester model is intended for checking tanks or vessels that may contain residual hydrocarbon vapors or water or may have been purged of oxygen. You can also use this model as a standard Eagle gas monitor by connecting the standard hose and probe and updating the oxygen alarms to the default settings.

Description

The tank tester model has an additional socket on the front on the housing to accommodate connection of the float probe assembly. This model includes the following non-standard components.

Float probe assembly

The float probe assembly helps prevent liquid from being drawn into the Eagle. The float probe assembly is 12-feet long. A quick disconnect fitting at one end of the assembly connects to the Eagle’s inlet fitting. The same end of the probe also includes a short wire that terminates in a jack. This jack connects to the float probe socket that is adjacent to the Eagle’s inlet fitting. The float probe switch at the opposite end of the 12-foot cable shuts off the pump if the probe begins to be submerged into a liquid.

To use the float probe assembly:

CAUTION:Drawing water, gasoline, or other liquids into the Eagle will cause damage.

1.Attach the quick disconnect fitting to the Eagle’s standard inlet fitting.

2.Attach the jack to the socket that is adjacent to the inlet fitting.

3.Lower the probe into the tank or vessel. Lower the probe very slowly to allow the float switch to activate if necessary.

Eagle Instruction Manual

Appendix F: Eagle Tank Tester Model • 67

Page 72 Page 74
Image 73
Page 72 Page 74
Contents RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510 Portable Multi-Gas DetectorWarranty WarrantyTable of Contents Table of Contents Display ModeCalibration Appendix F Eagle Tank Tester Model Overview IntroductionIntroduction About this Manual Specifications SpecificationsEagle Specifications Combustible Oxygen Standard Sensor SpecificationsCarbon Case DescriptionControl Panel ButtonsBattery Charger Connector Alarm LightsInterface Port BuzzerSensors CAL/SETUP Switch Methane Elimination SwitchCircuit Boards Starting Up the Eagle OperationOperation Operation Monitoring Combustible Gas in the PPM Range Normal OperationMonitoring Combustible Gases Other than Methane Full Response Mode Conversion Factors Methane CalibrationTarget Gas LEL Factor Turning Off the Eagle Setting User AccessAlarm Indications AlarmsAlarms Stel alarm toxics only Low flow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms Display Mode Display ModeUser and Station ID Screen Elapsed Time Screen Peak ScreenTo enter a user and station ID TWA/STEL Screen Battery Voltage ScreenDate/Time Screen Remaining Log Time Screen Clear Data Logger ScreensTo clear the data log Tips for Using Setup Mode Setup ModeSetup Mode Updating the Battery Type Setting Entering Setup ModeUpdating Channel Settings Setting a custom target gas label Target Gas Fullscale PPM Readings Equivalent to 100% LELUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Eagle’s Serial Number Updating the Lunch Break SettingUpdating the Alarm Silence Setting Updating the Alarm Latching SettingTurning the User ID Function On or Off Updating the Auto Calibration SettingsTurning the Auto Fresh Air Function On or Off Updating the Back Light SettingUpdating Log Data Over Write Setting data log option Updating the Interval Time Setting data log optionUpdating the Date and Time Settings data log option Updating the Time Calibration Setting data log optionUpdating the Confirmation Beep Setting Updating the Zero Follow SettingsReturning to Default Settings To reset all default alarm point settings To reset all default settingsTo reset the oxygen zero setting Calibration Supplies and Equipment CalibrationPreparing for Calibration CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Displaying the Battery Voltage MaintenanceTo display the battery voltage Replacing Alkaline BatteriesTo replace the combustibles sensor Replacing SensorsTo replace the oxygen sensor To replace the H2S or CO sensor Parts List Appendix a Parts ListAppendix a Parts List Part Number DescriptionPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Specifications Appendix C Non-Standard Toxic Gas SensorsDescription Non-Standard Toxic Gas Sensors SpecificationsCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Non-Standard Toxic Gas Sensors Parts ListAppendix D Carbon Dioxide Sensors Alarm TWA Alarm Stel AlarmCarbon Dioxide Sensor Specifications Appendix D Carbon Dioxide SensorsDemand Zero for Carbon Dioxide Sensors Normal Operation of Carbon Dioxide SensorsCalibrating Carbon Dioxide Sensors Carbon Dioxide Fresh Air ReadingsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Carbon Dioxide Sensors Appendix E Infrared Methane Sensors Range Alarm TWA Alarm Stel AlarmTarget Gases Infrared Methane Sensor SpecificationsSensor Analog PCB Socket Calibrating Infrared Methane SensorsReplacing Infrared Methane Sensors Parts List Infrared Methane SensorsAppendix F Eagle Tank Tester Model To use the float probe assemblyTo eliminate an oxygen alarm that is not being used AlarmsTo attach the dilution fitting Appendix F Eagle Tank Tester ModelCalibration Parts List Eagle Tank Tester ModelDisplaying Additional Channels Appendix G Five-Gas and Six-Gas ModelsAppendix G Five-Gas and Six-Gas Models Calibration, Display, and Setup Modes Appendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board

Eagle Series specifications

Eagle Home Products has established itself as a leader in the home appliance market with the introduction of the Eagle Series. Designed to meet the evolving demands of modern households, the Eagle Series offers a perfect blend of performance, efficiency, and innovation. This series encompasses a wide range of products, from kitchen appliances to home cleaning equipment, showcasing technologies that enhance user experience while promoting sustainability.

One of the standout features of the Eagle Series is its emphasis on energy efficiency. Each appliance is designed with advanced energy-saving technologies that comply with international energy standards. This not only helps consumers reduce their energy bills but also contributes to a greener environment. The appliances are constructed using eco-friendly materials, ensuring that they are safe for both users and the planet.

In terms of performance, the Eagle Series integrates smart technology into its appliances. Many models are equipped with Wi-Fi connectivity, enabling users to control and monitor their devices remotely through mobile applications. This feature enhances convenience, allowing users to schedule operations, receive alerts, and optimize energy usage from anywhere in their homes.

Another hallmark of the Eagle Series is its commitment to user-friendly design. Appliances in this series come with intuitive interfaces and clear displays that make operation straightforward for users of all ages. Whether it's a refrigerator with adjustable shelving or a vacuum cleaner with multiple cleaning modes, every product is designed to cater to the needs of the end-user.

Durability is also a key characteristic of the Eagle Series. Each product is built with high-quality materials that ensure longevity and reliability. Rigorous testing during the manufacturing process guarantees that these appliances can withstand the rigors of daily use, giving consumers peace of mind with their investment.

The Eagle Series also prioritizes safety, incorporating features such as automatic shut-off systems and child safety locks in various appliances. These additions provide an extra layer of protection, especially in homes with children or pets.

In summary, the Eagle Home Products Eagle Series stands out in the market for its innovative features, smart technologies, energy efficiency, user-friendly design, durability, and safety. As the demand for sustainable and efficient home appliances grows, the Eagle Series is well positioned to meet the needs of modern consumers while aligning with eco-friendly practices. Whether upgrading existing appliances or outfitting a new home, the Eagle Series proves to be a wise choice for those seeking quality and innovation.
Top Page Image Contents