Eagle Home Products Eagle Series instruction manual Maintenance, Displaying the Battery Voltage

Page 52

Maintenance

Displaying the Battery Voltage

Check the battery voltage periodically. Replace or recharge the batteries before the voltage drops to 4.5 V.

WARNING: Take the Eagle to a non-hazardous location before replacing or recharging the batteries.

To display the battery voltage:

1.From the normal screen, press the DISP/ADJ button to enter display mode.

2.Press the DISP/ADJ button until the Battery Voltage screen displays.

3.To exit display mode, press the DISP/ADJ button until the normal screen displays.

Replacing Alkaline Batteries

1.Turn off the Eagle.

2.Unscrew the two large screws on the top of the case, then carefully lift the top of the case and lay it aside.

3.Remove the batteries and verify that the battery compartment and electrical contacts are clean.

4.Insert fresh batteries following the label on the inside of the case.

5.Place the top of the case in its original position, then secure it with the large screws you loosened in step 1.

Recharging Ni-Cd Batteries

1.Turn off the Eagle.

2.Plug the cord from the charger into the Eagle’s battery charger connector.

3.Plug in the AC line cord or 12 VDC supply to the charger. A full charge takes approximately 8 to 12 hours.

4.Unplug the supply and the charger before using the Eagle. See the charger label for directions.

46 • Maintenance

Eagle Instruction Manual

Image 52

Contents

Portable Multi-Gas Detector RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510Warranty WarrantyTable of Contents Display Mode Table of ContentsCalibration Appendix F Eagle Tank Tester Model Overview IntroductionIntroduction About this Manual Speciﬁcations SpecificationsEagle Speciﬁcations Combustible Oxygen Standard Sensor SpeciﬁcationsCarbon Description CaseControl Panel ButtonsAlarm Lights Battery Charger ConnectorInterface Port BuzzerSensors CAL/SETUP Switch Methane Elimination SwitchCircuit Boards Starting Up the Eagle OperationOperation Operation Normal Operation Monitoring Combustible Gas in the PPM RangeMonitoring Combustible Gases Other than Methane Full Response Mode Conversion Factors Methane CalibrationTarget Gas LEL Factor Setting User Access Turning Off the EagleAlarm Indications AlarmsAlarms Stel alarm toxics only Low ﬂow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms Display Mode Display ModeUser and Station ID Screen Elapsed Time Screen Peak ScreenTo enter a user and station ID TWA/STEL Screen Battery Voltage ScreenDate/Time Screen Remaining Log Time Screen Clear Data Logger ScreensTo clear the data log Tips for Using Setup Mode Setup ModeSetup Mode Entering Setup Mode Updating the Battery Type SettingUpdating Channel Settings Setting a custom target gas label Fullscale PPM Readings Equivalent to 100% LEL Target GasUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Lunch Break Setting Updating the Eagle’s Serial NumberUpdating the Alarm Latching Setting Updating the Alarm Silence SettingUpdating the Auto Calibration Settings Turning the User ID Function On or OffUpdating the Back Light Setting Turning the Auto Fresh Air Function On or OffUpdating the Interval Time Setting data log option Updating Log Data Over Write Setting data log optionUpdating the Time Calibration Setting data log option Updating the Date and Time Settings data log optionUpdating the Conﬁrmation Beep Setting Updating the Zero Follow SettingsReturning to Default Settings To reset all default alarm point settings To reset all default settingsTo reset the oxygen zero setting Calibration Calibration Supplies and EquipmentPreparing for Calibration Calibration Calibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Maintenance Displaying the Battery VoltageTo display the battery voltage Replacing Alkaline BatteriesReplacing Sensors To replace the combustibles sensorTo replace the oxygen sensor To replace the H2S or CO sensor Appendix a Parts List Parts ListAppendix a Parts List Part Number DescriptionPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Appendix C Non-Standard Toxic Gas Sensors SpeciﬁcationsDescription Non-Standard Toxic Gas Sensors SpeciﬁcationsCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Parts List Non-Standard Toxic Gas SensorsAlarm TWA Alarm Stel Alarm Appendix D Carbon Dioxide SensorsCarbon Dioxide Sensor Speciﬁcations Appendix D Carbon Dioxide SensorsNormal Operation of Carbon Dioxide Sensors Demand Zero for Carbon Dioxide SensorsCalibrating Carbon Dioxide Sensors Carbon Dioxide Fresh Air ReadingsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Carbon Dioxide Sensors Range Alarm TWA Alarm Stel Alarm Appendix E Infrared Methane SensorsTarget Gases Infrared Methane Sensor SpeciﬁcationsCalibrating Infrared Methane Sensors Sensor Analog PCB SocketParts List Infrared Methane Sensors Replacing Infrared Methane SensorsTo use the ﬂoat probe assembly Appendix F Eagle Tank Tester ModelAlarms To eliminate an oxygen alarm that is not being usedTo attach the dilution ﬁtting Appendix F Eagle Tank Tester ModelParts List Eagle Tank Tester Model CalibrationDisplaying Additional Channels Appendix G Five-Gas and Six-Gas ModelsAppendix G Five-Gas and Six-Gas Models Calibration, Display, and Setup Modes Appendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board