Eagle Home Products Eagle Series instruction manual Calibration Supplies and Equipment

Page 47

Calibration

Calibrate the Eagle when you replace a sensor. Also calibrate the Eagle periodically to assure proper sensor response.

You can program the Eagle to notify you when it is due for calibration (see “Updating the Time Calibration Setting” on page 38). The frequency of calibration depends upon the amount and type of use. A typical calibration frequency is once per month.

Calibration Supplies and Equipment

To calibrate the Eagle, you need:

•Known calibrating samples of combustible and the appropriate toxic gases. The samples should have concentrations in approximately the middle of the range of detection.

•An oxygen-free source, such as 100% nitrogen or CO in a nitrogen balance

•A demand-flow regulator to provide adequate sample gas flow

For one-source, auto-calibration, you can use the RKI Four-Gas Cylinder to adjust all the sensors at the same time, automatically, with no need for a zero-oxygen source. This section includes instructions for calibration with the demand-flow regulator and RKI Four-Gas Cylinder. This section also includes instructions for calibration with individual gas sources.

Preparing for Calibration

1.Take the Eagle to a non-hazardous location with fresh-air conditions.

2.Turn on the Eagle and allow one minute for warm up.

3.Press and hold the AIR/▲ button until a tone sounds.

The Eagle automatically sets the combustible gas and toxics circuits to zero and the oxygen circuit to 20.9%.

4.Screw the regulator to the calibration cylinder.

5.Connect the calibration tubing to the regulator.

Eagle Instruction Manual

Calibration • 41

Page 46 Page 48
Image 47
Page 46 Page 48
Contents RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510 Portable Multi-Gas DetectorWarranty WarrantyTable of Contents Table of Contents Display ModeCalibration Appendix F Eagle Tank Tester Model Introduction IntroductionOverview About this Manual Eagle Specifications SpecificationsSpecifications Carbon Standard Sensor SpecificationsCombustible Oxygen Buttons DescriptionCase Control PanelBuzzer Alarm LightsBattery Charger Connector Interface PortSensors Circuit Boards Methane Elimination SwitchCAL/SETUP Switch Operation OperationStarting Up the Eagle Operation Monitoring Combustible Gas in the PPM Range Normal OperationTarget Gas LEL Factor Full Response Mode Conversion Factors Methane CalibrationMonitoring Combustible Gases Other than Methane Turning Off the Eagle Setting User AccessAlarms AlarmsAlarm Indications Stel alarm toxics only Low flow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms User and Station ID Screen Display ModeDisplay Mode To enter a user and station ID Peak ScreenElapsed Time Screen Date/Time Screen Battery Voltage ScreenTWA/STEL Screen To clear the data log Clear Data Logger ScreensRemaining Log Time Screen Setup Mode Setup ModeTips for Using Setup Mode Updating the Battery Type Setting Entering Setup ModeUpdating Channel Settings Setting a custom target gas label Target Gas Fullscale PPM Readings Equivalent to 100% LELUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Eagle’s Serial Number Updating the Lunch Break SettingUpdating the Alarm Silence Setting Updating the Alarm Latching SettingTurning the User ID Function On or Off Updating the Auto Calibration SettingsTurning the Auto Fresh Air Function On or Off Updating the Back Light SettingUpdating Log Data Over Write Setting data log option Updating the Interval Time Setting data log optionUpdating the Date and Time Settings data log option Updating the Time Calibration Setting data log optionReturning to Default Settings Updating the Zero Follow SettingsUpdating the Confirmation Beep Setting To reset the oxygen zero setting To reset all default settingsTo reset all default alarm point settings Calibration CalibrationCalibration Supplies and Equipment Preparing for CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Replacing Alkaline Batteries MaintenanceDisplaying the Battery Voltage To display the battery voltageTo replace the combustibles sensor Replacing SensorsTo replace the oxygen sensor To replace the H2S or CO sensor Part Number Description Appendix a Parts ListParts List Appendix a Parts ListPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Non-Standard Toxic Gas Sensors Specifications Appendix C Non-Standard Toxic Gas SensorsSpecifications DescriptionCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Non-Standard Toxic Gas Sensors Parts ListAppendix D Carbon Dioxide Sensors Alarm TWA Alarm Stel AlarmAppendix D Carbon Dioxide Sensors Carbon Dioxide Sensor SpecificationsCarbon Dioxide Fresh Air Readings Normal Operation of Carbon Dioxide SensorsDemand Zero for Carbon Dioxide Sensors Calibrating Carbon Dioxide SensorsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Carbon Dioxide Sensors Infrared Methane Sensor Specifications Range Alarm TWA Alarm Stel AlarmAppendix E Infrared Methane Sensors Target GasesSensor Analog PCB Socket Calibrating Infrared Methane SensorsReplacing Infrared Methane Sensors Parts List Infrared Methane SensorsAppendix F Eagle Tank Tester Model To use the float probe assemblyAppendix F Eagle Tank Tester Model AlarmsTo eliminate an oxygen alarm that is not being used To attach the dilution fittingCalibration Parts List Eagle Tank Tester ModelAppendix G Five-Gas and Six-Gas Models Appendix G Five-Gas and Six-Gas ModelsDisplaying Additional Channels Calibration, Display, and Setup Modes Appendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board

Eagle Series specifications

Eagle Home Products has established itself as a leader in the home appliance market with the introduction of the Eagle Series. Designed to meet the evolving demands of modern households, the Eagle Series offers a perfect blend of performance, efficiency, and innovation. This series encompasses a wide range of products, from kitchen appliances to home cleaning equipment, showcasing technologies that enhance user experience while promoting sustainability.

One of the standout features of the Eagle Series is its emphasis on energy efficiency. Each appliance is designed with advanced energy-saving technologies that comply with international energy standards. This not only helps consumers reduce their energy bills but also contributes to a greener environment. The appliances are constructed using eco-friendly materials, ensuring that they are safe for both users and the planet.

In terms of performance, the Eagle Series integrates smart technology into its appliances. Many models are equipped with Wi-Fi connectivity, enabling users to control and monitor their devices remotely through mobile applications. This feature enhances convenience, allowing users to schedule operations, receive alerts, and optimize energy usage from anywhere in their homes.

Another hallmark of the Eagle Series is its commitment to user-friendly design. Appliances in this series come with intuitive interfaces and clear displays that make operation straightforward for users of all ages. Whether it's a refrigerator with adjustable shelving or a vacuum cleaner with multiple cleaning modes, every product is designed to cater to the needs of the end-user.

Durability is also a key characteristic of the Eagle Series. Each product is built with high-quality materials that ensure longevity and reliability. Rigorous testing during the manufacturing process guarantees that these appliances can withstand the rigors of daily use, giving consumers peace of mind with their investment.

The Eagle Series also prioritizes safety, incorporating features such as automatic shut-off systems and child safety locks in various appliances. These additions provide an extra layer of protection, especially in homes with children or pets.

In summary, the Eagle Home Products Eagle Series stands out in the market for its innovative features, smart technologies, energy efficiency, user-friendly design, durability, and safety. As the demand for sustainable and efficient home appliances grows, the Eagle Series is well positioned to meet the needs of modern consumers while aligning with eco-friendly practices. Whether upgrading existing appliances or outfitting a new home, the Eagle Series proves to be a wise choice for those seeking quality and innovation.
Top Page Image Contents