Eagle Home Products Eagle Series instruction manual To replace the H2S or CO sensor

Page 55

To replace the H2S or CO sensor:

1.Take the Eagle to a non-hazardous location, and turn the power off.

2.Unscrew the two large screws on the top of the case, then carefully lift the top of the case and lay it aside.

3.Locate the toxic gas sensor you intend to replace. With the batteries closest to you, the sensor for Channel 3 is at the top right corner of the sensor block, and the sensor for Channel 4 is at the bottom right corner of the sensor block. Note the color of the leads extending from the sensor you intend to replace.

4.Unplug the appropriate sensor connector from the circuit board. Use the color of the leads to determine the appropriate connector.

5.Remove the sensor from the sensor block. If necessary, wiggle the sensor to work it out of the seal.

6.Install the replacement sensor in reverse order.

CAUTION:Verify that you install the H2S or CO sensor in the appropriate flow block position. The Eagle will display inaccurate H2S and

CO readings if the sensors are not installed in the correct flow block positions.

The Eagle continues to display H2S and CO readings in the

same channels as it did previously regardless of which socket (EC1 or EC2) the sensor is wired to or into which flow block position the sensor is installed. However, the H2S and CO

reading will be inaccurate due to the charcoal filter installed before the CO flow block position.

Eagle Instruction Manual

Maintenance • 49

Page 54 Page 56
Image 55
Page 54 Page 56
Contents RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510 Portable Multi-Gas DetectorWarranty WarrantyTable of Contents Table of Contents Display ModeCalibration Appendix F Eagle Tank Tester Model Overview IntroductionIntroduction About this Manual Specifications SpecificationsEagle Specifications Combustible Oxygen Standard Sensor SpecificationsCarbon Buttons DescriptionCase Control PanelBuzzer Alarm LightsBattery Charger Connector Interface PortSensors CAL/SETUP Switch Methane Elimination SwitchCircuit Boards Starting Up the Eagle OperationOperation Operation Monitoring Combustible Gas in the PPM Range Normal OperationMonitoring Combustible Gases Other than Methane Full Response Mode Conversion Factors Methane CalibrationTarget Gas LEL Factor Turning Off the Eagle Setting User AccessAlarm Indications AlarmsAlarms Stel alarm toxics only Low flow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms Display Mode Display ModeUser and Station ID Screen Elapsed Time Screen Peak ScreenTo enter a user and station ID TWA/STEL Screen Battery Voltage ScreenDate/Time Screen Remaining Log Time Screen Clear Data Logger ScreensTo clear the data log Tips for Using Setup Mode Setup ModeSetup Mode Updating the Battery Type Setting Entering Setup ModeUpdating Channel Settings Setting a custom target gas label Target Gas Fullscale PPM Readings Equivalent to 100% LELUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Eagle’s Serial Number Updating the Lunch Break SettingUpdating the Alarm Silence Setting Updating the Alarm Latching SettingTurning the User ID Function On or Off Updating the Auto Calibration SettingsTurning the Auto Fresh Air Function On or Off Updating the Back Light SettingUpdating Log Data Over Write Setting data log option Updating the Interval Time Setting data log optionUpdating the Date and Time Settings data log option Updating the Time Calibration Setting data log optionUpdating the Confirmation Beep Setting Updating the Zero Follow SettingsReturning to Default Settings To reset all default alarm point settings To reset all default settingsTo reset the oxygen zero setting Calibration CalibrationCalibration Supplies and Equipment Preparing for CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Replacing Alkaline Batteries MaintenanceDisplaying the Battery Voltage To display the battery voltageTo replace the combustibles sensor Replacing SensorsTo replace the oxygen sensor To replace the H2S or CO sensor Part Number Description Appendix a Parts ListParts List Appendix a Parts ListPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Non-Standard Toxic Gas Sensors Specifications Appendix C Non-Standard Toxic Gas SensorsSpecifications DescriptionCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Non-Standard Toxic Gas Sensors Parts ListAppendix D Carbon Dioxide Sensors Alarm TWA Alarm Stel AlarmAppendix D Carbon Dioxide Sensors Carbon Dioxide Sensor SpecificationsCarbon Dioxide Fresh Air Readings Normal Operation of Carbon Dioxide SensorsDemand Zero for Carbon Dioxide Sensors Calibrating Carbon Dioxide SensorsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Carbon Dioxide Sensors Infrared Methane Sensor Specifications Range Alarm TWA Alarm Stel AlarmAppendix E Infrared Methane Sensors Target GasesSensor Analog PCB Socket Calibrating Infrared Methane SensorsReplacing Infrared Methane Sensors Parts List Infrared Methane SensorsAppendix F Eagle Tank Tester Model To use the float probe assemblyAppendix F Eagle Tank Tester Model AlarmsTo eliminate an oxygen alarm that is not being used To attach the dilution fittingCalibration Parts List Eagle Tank Tester ModelDisplaying Additional Channels Appendix G Five-Gas and Six-Gas ModelsAppendix G Five-Gas and Six-Gas Models Calibration, Display, and Setup Modes Appendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board

Eagle Series specifications

Eagle Home Products has established itself as a leader in the home appliance market with the introduction of the Eagle Series. Designed to meet the evolving demands of modern households, the Eagle Series offers a perfect blend of performance, efficiency, and innovation. This series encompasses a wide range of products, from kitchen appliances to home cleaning equipment, showcasing technologies that enhance user experience while promoting sustainability.

One of the standout features of the Eagle Series is its emphasis on energy efficiency. Each appliance is designed with advanced energy-saving technologies that comply with international energy standards. This not only helps consumers reduce their energy bills but also contributes to a greener environment. The appliances are constructed using eco-friendly materials, ensuring that they are safe for both users and the planet.

In terms of performance, the Eagle Series integrates smart technology into its appliances. Many models are equipped with Wi-Fi connectivity, enabling users to control and monitor their devices remotely through mobile applications. This feature enhances convenience, allowing users to schedule operations, receive alerts, and optimize energy usage from anywhere in their homes.

Another hallmark of the Eagle Series is its commitment to user-friendly design. Appliances in this series come with intuitive interfaces and clear displays that make operation straightforward for users of all ages. Whether it's a refrigerator with adjustable shelving or a vacuum cleaner with multiple cleaning modes, every product is designed to cater to the needs of the end-user.

Durability is also a key characteristic of the Eagle Series. Each product is built with high-quality materials that ensure longevity and reliability. Rigorous testing during the manufacturing process guarantees that these appliances can withstand the rigors of daily use, giving consumers peace of mind with their investment.

The Eagle Series also prioritizes safety, incorporating features such as automatic shut-off systems and child safety locks in various appliances. These additions provide an extra layer of protection, especially in homes with children or pets.

In summary, the Eagle Home Products Eagle Series stands out in the market for its innovative features, smart technologies, energy efficiency, user-friendly design, durability, and safety. As the demand for sustainable and efficient home appliances grows, the Eagle Series is well positioned to meet the needs of modern consumers while aligning with eco-friendly practices. Whether upgrading existing appliances or outfitting a new home, the Eagle Series proves to be a wise choice for those seeking quality and innovation.
Top Page Image Contents