Hearth and Home Technologies SOHO-CE manual Maintaining and Servicing Appliance, Maintenance Tasks

Page 32

15 Maintaining and Servicing Appliance

A. Maintenance Tasks

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-up at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

•Turn off gas.

•Turn off electricity to appliance.

•Disable remote control, if one is present.

•Ensure appliance is completely cooled.

After servicing:

•Replace any screen or barrier that was removed.

•Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

•Condition of doors, surrounds and fronts.

•Condition of glass, glass assembly and glass seal.

•Obstructions of combustion and ventilation air.

•Condition of logs.

•Condition of firebox.

•Burner ignition and operation.

•Burner air shutter adjustment

•Gas connections and fittings.

•Obstructions of termination cap.

Clean:

• Glass

•Air passageways, control compartment

•Burner, burner ports

Risk of:

•Fire

•Delayed ignition or explosion

•Exposure to combustion fumes

•Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial 3-4 hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

•Avoid striking, scratching or slamming glass.

•Do NOT use abrasive cleaners.

•Use a hard water deposit glass cleaner on white film.

•Do NOT clean glass when hot.

•Turn off appliance after 3-4 hours of operation and

ALLOW TO COOL.

•Remove and clean glass assembly.

•Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external flue cap regularly.

•Ensure no debris blocks cap.

•Combustible materials blocking cap may ignite.

•Restricted air flow affects burner operation.

32

Heat & Glo • Soho-CE • 2111-900 Rev. D • 6/07

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Model Soho-CE What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Appliance CertificationNon-Combustible Materials Specification Combustible Materials SpecificationDesign and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies Needed84.1 74.0 118.7 89.2 Framing and ClearancesSelecting Appliance Location Constructing the Appliance Chase ClearancesTermination Locations Flue Termination Minimum ClearancesSee .4 for specific clearances Cm minimum in snow regionsAlcove Applications Flue Information and Diagrams Flue Table KeyUse of Elbows Measuring StandardsFlue Diagrams Horizontal Termination One Elbow Two Elbows One Elbow Minimum Maximum+ H Maximum = 11.9 m Maximum = 4.6 m Two Elbows Minimum + H 2 Maximum Elbow only Not Allowed+ V 2 + H = Maximum = 11.9 m + H 2 Maximum = 4.6 m Horizontal Termination Three ElbowsThree Elbows Minimum Maximum Vertical Termination No Elbow Two Elbows V1 = 11.8 m MaximumTwo Elbows V1 Minimum Maximum V1 + V2 + H Maximum = 11.9 m+ V2 + H1 + H2 Maximum = 11.9 m Maximum = 4.3 m Vertical Termination Three ElbowsThree Elbows V1 Minimum H1 + H2 Maximum Flue Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Appliance Preparation Securing and Leveling the ApplianceInstalling Flue Pipe Assembly of Flue SectionsInstall Support Brackets Attach the First Flue Component to Starting CollarsFor Horizontal Runs Wall shield firestops are Required Installing Firestops and Horizontal Termination CapInstalling the Horizontal Termination Cap Install Roof Flashing and Vertical Termination Cap Assembling and Installing Storm Collar Sharp EdgesGas Information Gas Pressure RequirementsGas Connection Natural Gas Propane Butane G20 G31 G30 G25Electronic Ignition System Wiring Electrical InformationFinishing Facing MaterialMantel Projections See for combustible/non-combustible definitionsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Assembly LOGS-SOHOCE Positioning the LogsReplacing Glass Assembly Glass AssemblyRemoving Glass Assembly Operating Instructions Before Lighting ApplianceLighting the Fireplace Electronic IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Troubleshooting Symptom Possible Causes Corrective ActionsElectronic Ignition System No transmission, motor Receiver mustMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Recommend addition of screen if one is not presentVerify no obstructions to airflow through the louvers Operating properly. Replace as necessaryAppliance Dimension Diagram Appliance Dimensions TableReference Materials Location Centimeter108 Service Parts ListLog Set Assembly SOHO-CE Service Parts SOHO-CELimited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Important operating

SOHO-CE specifications

Hearth and Home Technologies (HHT) has long been a leader in the design and manufacturing of innovative hearth products, and their SOHO-CE model is no exception. This sleek and modern electric fireplace represents a perfect synthesis of aesthetic appeal and functional engineering, specifically tailored for small office/home office (SOHO) settings.

One of the standout features of the SOHO-CE is its Clean Edge design, which allows for a seamless installation that blends effortlessly into any room. This contemporary electric fireplace has a minimalist frame available in various finishes, making it versatile enough to complement different interior styles, from modern to rustic. Its elegant look is well-suited for both residential and commercial spaces, providing an inviting ambiance that enhances the room's overall atmosphere.

The SOHO-CE employs state-of-the-art LED technology to create realistic flame effects. These flames can be adjusted to suit individual preferences, giving users control over the intensity and color. This customization is essential in creating the ideal mood for any occasion, whether it’s a productive workday or a cozy evening at home. In addition, the electric fireplace boasts a safe and efficient heat source with adjustable heat settings, ensuring comfort without compromising safety.

Smart technology integration is another significant characteristic of the SOHO-CE. It can be controlled via a user-friendly app, allowing for remote operation right from a smartphone or tablet. This feature is particularly beneficial for those who want to set the fireplace to a specific schedule, ensuring their space is warm and inviting upon arrival.

In terms of energy efficiency, the SOHO-CE stands out with its eco-friendly operation. As an electric fireplace, it eliminates the need for venting and reduces the emission of pollutants, making it a responsible choice for the environment. It also offers the convenience of heating only when necessary, reducing energy consumption.

Durability is built into the SOHO-CE’s design, featuring high-quality materials that ensure longevity and performance. This electric fireplace is also easy to maintain, with no need for chimneys or flue cleaning. Overall, Hearth and Home Technologies' SOHO-CE is a remarkable addition to any SOHO setting, marrying functionality with style for an exceptional user experience. Whether for work or leisure, this electric fireplace elevates any space.
Top Page Image Contents