Hearth and Home Technologies SOHO-CE manual Framing and Clearances, Selecting Appliance Location

Page 6

3 Framing and Clearances

Note:

•Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY.

•Illustrations/diagrams are not drawn to scale.

•Actual installation may vary due to individual design preference.

A.Selecting Appliance Location

When selecting a location for your appliance it is important to consider the required clearances to walls (see Figure 3.1).

WARNING

Fire Risk

Provide adequate clearance:

•Around air openings

•To combustibles

• For service access

Locate appliance away from trafﬁc areas.

NOTE: For actual appliance dimensions refer to Sec- tion 16.

1.3cm

TOP VENT, ONE 90º ELBOW

ALCOVE

INSTALLATION

MINIMUM

	A	B	C	D
Centimeters	84.1	74.0	118.7	89.2

In addition to these framing dimensions, also reference the following sections:

•Clearances and Mantel Projections (Sections 3.C and 11.B).

•Flue Clearances and Framing (Section 6).

Figure 3.1 Appliance Locations

6	Heat & Glo • Soho-CE • 2111-900 Rev. D • 6/07

Image 6

Contents Model Soho-CE What to do if you smell gasCongratulations Homeowner Reference Information Table of Contents Non-Combustible Materials Speciﬁcation Listing and Code ApprovalsAppliance Certiﬁcation Combustible Materials SpeciﬁcationInspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededFraming and Clearances Selecting Appliance Location84.1 74.0 118.7 89.2 Constructing the Appliance Chase ClearancesSee .4 for speciﬁc clearances Termination LocationsFlue Termination Minimum Clearances Cm minimum in snow regionsAlcove Applications Use of Elbows Flue Information and DiagramsFlue Table Key Measuring Standards+ H Maximum = 11.9 m Maximum = 4.6 m Flue Diagrams Horizontal Termination One Elbow Two ElbowsOne Elbow Minimum Maximum Two Elbows Minimum + H 2 Maximum Elbow only Not AllowedHorizontal Termination Three Elbows Three Elbows Minimum Maximum+ V 2 + H = Maximum = 11.9 m + H 2 Maximum = 4.6 m Two Elbows V1 Minimum Maximum Vertical Termination No Elbow Two ElbowsV1 = 11.8 m Maximum V1 + V2 + H Maximum = 11.9 mVertical Termination Three Elbows Three Elbows V1 Minimum H1 + H2 Maximum+ V2 + H1 + H2 Maximum = 11.9 m Maximum = 4.3 m Wall Penetration Framing Flue Clearances and FramingPipe Clearances to Combustibles Combustible Wall PenetrationInstalling the Ceiling Firestop Installing Attic ShieldVertical Penetration Framing Appliance Preparation Securing and Leveling the ApplianceInstall Support Brackets Installing Flue PipeAssembly of Flue Sections Attach the First Flue Component to Starting CollarsInstalling Firestops and Horizontal Termination Cap Installing the Horizontal Termination CapFor Horizontal Runs Wall shield ﬁrestops are Required Install Roof Flashing and Vertical Termination Cap Assembling and Installing Storm Collar Sharp EdgesGas Connection Gas InformationGas Pressure Requirements Natural Gas Propane Butane G20 G31 G30 G25Electronic Ignition System Wiring Electrical InformationMantel Projections FinishingFacing Material See for combustible/non-combustible deﬁnitionsAccessories Appliance SetupClean the Appliance Ember PlacementLog Assembly LOGS-SOHOCE Positioning the LogsGlass Assembly Removing Glass AssemblyReplacing Glass Assembly Operating Instructions Before Lighting ApplianceLighting the Fireplace Electronic IgnitionFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Electronic Ignition System TroubleshootingSymptom Possible Causes Corrective Actions No transmission, motor Receiver mustMaintenance Tasks Maintaining and Servicing ApplianceVerify no obstructions to airﬂow through the louvers Inspect Maintenance TasksRecommend addition of screen if one is not present Operating properly. Replace as necessaryReference Materials Appliance Dimension DiagramAppliance Dimensions Table Location CentimeterService Parts List Log Set Assembly108 SOHO-CE Service Parts SOHO-CELimited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information Important operating